Sonance Landscape LS4T SAT Manual

Sonance Højttaler Landscape LS4T SAT

Læs gratis den danske manual til Sonance Landscape LS4T SAT (5 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Sonance Landscape LS4T SAT, eller vil du spørge andre brugere om produktet?

Side 1/5
SATELLITE SPEAKERS
I N S T R U C T I O N M A N U A L
LS4T SAT | LS6T SAT
Figure 2
Figure 1: Placement
Introduction
Thank you for purchasing SLS Speakers. When properly installed,
these speakers will provide you with years of outdoor entertainment
pleasure. To get the most out of your new speakers, please read
this manual thoroughly before you begin installation.
Satellite Placement
The SLS system is designed to deliver a seamless, evenly
dispersed sound eld in an ‘open air’ environment. An array of
multiple Satellite speakers and Subwoofers should be strategically
placed to minimize ‘hot spots’ and ‘nulls’ as you move around the
outdoor entertainment area. Recommended placement of the SLS
Satellite models is every 8-10 feet around the area of coverage.
The shorter spacing is recommended for higher SPL and closer
listening applications. After every 4-5 satellites, install one SLS
Subwoofer of choice within the speaker wire chain. This will
allow the output of the satellite speakers and subwoofer to blend
together more seamlessly. See Figure 1.
Use care to select satellite locations that are equally distant from
the main listening area. When possible, use high and low locations
to centralize the acoustic stage. See Figure 2.
Sonamp DSP 2-750 Amplier Power Planning
The maximum number of satellites and subwoofers that can be
used in a system will depend on the amplier power. It is important
to calculate the amplier power your installation will require before
you begin. Multiple ampliers may be required in large installations.
Refer to the SLS wattage calculator on the Sonance website:
www.sonance.com/outdoor/new-sls/satellite-speakers.
1
Adjustable Tap
This Sonance Landscape Series product features a wide bandwidth
Sonance Laminated Core Transformer (SLCT) with an adjustable
tap, allowing the system to be congured for 70V/100V or 8 ohm.
If using this SLS product in an 8 ohm application, ensure the tap
switch is positioned to the 8 ohm setting. If using this product in
a 70V/100V system, ensure the tap is positioned to one of the
70V/100V settings.
Some 70V/100V system designs will require variations of higher
and lower output in dierent areas of the landscaping. The SLCT
adjustable tap allows each satellite or subwoofer to be individually
dialed to the desired output. Adjusting the tap settings will impact
your wattage calculations. Please review the Wattage Calculator
on the Sonance website: www.sonance.com/outdoor/new-sls/
satellite-speakers for more information.
NOTE: AS A GENERAL GUIDELINE, (1) SATELLITE WILL COVER ABOUT 250
SQUARE FEET OF LISTENING AREA
Box Contents
(1) Satellite Speaker
(2) Silicone lled wire nuts
LS4T SAT
Landscape Series Satellite Speaker
NOTE: THIS PRODUCT SHIPS WITH THE SLCT ADJUSTABLE TAP SET
TO 40W. ADJUSTMENTS CAN BE MADE TO THE TAP SWITCH ONCE ALL
THE SATELLITES AND SUBWOOFERS ARE CONNECTED TO ACHIEVE THE
APPROPRIATE OUTPUT LEVEL.
NOTE: ENSURE THAT ALL SATELLITES AND SUBWOOFERS ARE SET TO
EITHER 70V/100V OR 8 OHM TAP SETTINGS TO AVOID ANY DAMAGE TO
YOUR AMPLIFIER. DO NOT COMBINE PRODUCTS SET TO ANY OF THE
70V/100V SETTINGS WITH PRODUCTS SET TO THE 8 OHM SETTING ON A
SINGLE AMPLIFIER.


Produkt Specifikationer

Mærke: Sonance
Kategori: Højttaler
Model: Landscape LS4T SAT

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonance Landscape LS4T SAT stil et spørgsmål nedenfor, og andre brugere vil svare dig