Sonance Visual Performance Extreme VPXT8R Manual

Sonance Højttaler Visual Performance Extreme VPXT8R

Læs gratis den danske manual til Sonance Visual Performance Extreme VPXT8R (3 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Sonance Visual Performance Extreme VPXT8R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Box Contents

VPXT6 or VPXT6R or VPXT8R

(1) Quickstart guide / cutout template

(2) Speakers

(2) Paintable grilles

VPXT6R SST

(1) Quickstart guide / cutout template

(1) Speaker

(1) Paintable grille

EXTREME SPEAKERS INSTRUCTION MANUAL

VPXT6 | VPXT6R | VPXT6R SST | VPXT8R

SONANCE VISUAL PERFORMANCE SERIES

Introduction

Thank you for purchasing Sonance Visual Performance

Series Speakers. This guide covers the following speaker

models: VPXT6 (6” Rectangular), VPXT6R (6” Round),

VPXT6R SST (6” Round, Single-Stereo Technology

) and

VPXT8R (8” Round).

Before Installation: Retro-t

1. Determine the location for the speaker.

2. Perform an obstruction survey to be certain that there are

no studs, conduit, pipes, heating ducts, pocket doors

or air returns in the wall cavity that will interfere with

the speaker.

3. Position the included cutout template where the

speaker is to be located and pencil an outline on the

wall or ceiling.

• If you are unsure about obstructions, drill a small hole

in the center of the outline and insert a coat hanger wire

into the hole to feel-around for possible obstructions.

4. Cut the mounting hole using tools appropriate for the

construction, and run the speaker wires from the

mounting hole to the amplier location.

Installation

Sonance Visual Performance Series Extreme speakers

feature an exclusive integral RotoLock

mounting system for

quick mounting directly into existing walls and ceilings.

1. Strip 1/4” – 1/2” (6mm – 13mm) of insulation from each

speaker lead. Twist the strands or tin the exposed wire

with solder to ensure that there are no stray strands.

NOTE: CONSULT LOCAL BUILDING CODES BEFORE RUNNING

SPEAKER WIRES THROUGH WALLS.

NOTE: STRAY STRANDS THAT TOUCH EACH OTHER CAN CAUSE A

SHORT- CIRCUIT THAT CAN DAMAGE THE AMPLIFIER.

2. The speaker’s connector posts are spring-loaded.

Push the top of each connector post down to open the

connector and insert the exposed wires into the holes in

the posts (see Figure 1).

3. The speaker’s positive post is labeled with a red dot; the

negative post is labeled with a black dot.

• The VPXT6R SST has two sets of connection terminals,

located on opposite sides of the crossover board.

4. After making all connections, double-check that you

connected amplier “+” to speaker “+” and amplier “–”

to speaker “–”.

5. Make sure all the Roto-Lock toggle feet are retracted so

that they are tucked within the mounting hole’s border.

Figure 1: Connection Terminals

Figure 2: Roto-Lock Toggle Feet Retracted

Connection Terminals

NOTE: THE ROTO-LOCK SYSTEM CAN ACCOMMODATE A WALL

MATERIAL THICKNESS OF 1 1/4” (32MM) WITH THE TOGGLE

FOOT CAP REMOVED THE SYSTEM CAN ACCOMMODATE A WALL

MATERIAL THICKNESS OF 1 3/4” (44MM). TO REMOVE THE

CLAMP FEET, USE A SMALL SCREWDRIVER TO GENTLY RELEASE

THE LOCKING LEVERS (FIGURE 3, LEFT). THEN REMOVE THE FEET

FROM THE CLAMPS (FIGURE 3, RIGHT).

Figure 3: Removing the Roto-Lock Clamp Feet

VISUAL PERFORMANCE EXTREME SPEAKERS INSTRUCTION MANUAL

6. Insert the speaker into the mounting hole (Figure 4) and

tighten the four screws on the front of the speaker bae.

(Figure 5).

7. The Roto-Lock clamps will automatically rotate into

position and begin clamping the speaker.

8. The Visual Performance Extreme Grille features Sonance

Extreme Post Capture (XPC) technology. XPC holds the

grille in place by several small magnets located on the

posts of the grille and inside the post holes located on

the speaker bae (Figure 6). Place the grille against the

speaker, aligning the grille posts and post holes.

The magnets will pull the grille posts into the post holes

and hold the grille rmly in place. When the grille is

properly installed, the grille trim should make contact

with the mounting surface all the way around the speaker.

Figure 5: Tightening the Roto-Lock Screws

Figure 4: Inserting the Speaker into the Mounting Hole

Figure 6: Attaching the Grille

IMPORTANT: ALWAYS USE LOW-TORQUE SETTINGS WHEN USING A

SCREW GUN; NEVER OVER TIGHTEN.

NOTE: ADJUSTING THE TENSION OF THE ROTO-LOCK CLAMPS SO

THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE

GRILLE CONTACTS THE WALL ALL THE WAY AROUND THE SPEAKER

FOR A PROPER FIT.

NOTE: EXTREME POST CAPTURE TECHNOLOGY INVOLVES STRONG

MAGNETS THAT MAY CAUSE A FAST CONNECTION WHEN THE

GRILLE IS BEING INSTALLED ONTO THE SPEAKER. TAKE CAUTION

WHEN ALIGNING THE POSTS TO THE HOLES TO PROTECT FINGERS

FROM GETTING CAUGHT.

Roto-Lock

Screws

PAINTING THE GRILLES

Sonance Visual Performance Series speaker grilles

completely cover the exposed speaker frame, so only the

grilles (not the speakers themselves) require painting.

1. Prime the grille with a metal primer/bonder in a spray can.

Carefully follow the manufacturerʼs directions on the can.

2. We recommend using water-based latex paint on

the grilles. Thin the paint with a proper thinning agent

to a ratio of 1:1 paint-to-thinner, and strain it through a

standard mesh strainer to remove any lumps.

3. Use a small touch-up gun or cap-spray gun with a #3 tip

for painting.

(A) Set the nozzle with a medium to wide fan.

(B) Set the pressure regulator to 60psi.

from approximately 10 inches away.

(D) Let the paint set for a minute, then turn the grille 90º

and lightly spray the grille again in 3 quick strokes.

Repeat this step until all four sides of the grille have

been evenly painted.

4. While the paint is still wet, inspect the grille and make

sure that excess paint has not collected underneath the

grille frame, and that none of the grille perforations are

lled with paint. If any are, use compressed air to blow

the paint out of the perforations.

5. Once the paint has thoroughly dried, mount the grille on

the speaker.

IMPORTANT: DUE TO ITS INCREASED DURABILITY, OIL-BASED

PAINT SHOULD BE CONSIDERED FOR VP EXTREME SERIES

SPEAKERS THAT ARE INSTALLED OUTDOORS.

IMPORTANT: IF YOU FIND ANY GRILLE PERFORATIONS THAT ARE

PLUGGED WITH PAINT AFTER THE PAINT HAS DRIED, USE A STRAIGHT

PIN OR SEWING NEEDLE TO CAREFULLY REMOVE THE PAINT.

Produkt Specifikationer

Mærke:	Sonance
Kategori:	Højttaler
Model:	Visual Performance Extreme VPXT8R

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonance Visual Performance Extreme VPXT8R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Sonance Manualer

Sonance Invisible Series IS10W Manual

3 Marts 2025

Sonance Visual Experience VX86 Manual

26 Februar 2025

Sonance Invisible Series IS10 Manual

26 Februar 2025

Sonance Visual Experience VX86R SST Manual

26 Februar 2025

Sonance Visual Experience VX66R Manual

26 Februar 2025

Sonance MAG8R Manual

13 Januar 2025

Sonance Visual Performance Extreme VPXT8R Manual

8 Januar 2025

Sonance Visual Performance VP38R Manual

8 Januar 2025

Sonance MAG5.1R Manual

8 Januar 2025

Sonance MAG6R Manual

8 Januar 2025

Højttaler Manualer

Nyeste Højttaler Manualer

Proscan PSP1820 Manual

30 September 2025

Insignia NS-IOPS22 Manual

29 September 2025

August MS425 Manual

29 September 2025

Insignia Mini Sonic NS-MINISONIC20 Manual

29 September 2025

Insignia NS-2810BT Manual

29 September 2025

Wohler iAM-SUM8 Manual

29 September 2025

Mount-It! MI-SB434 Manual

29 September 2025

Wohler HDM-215-3G-TT Manual

29 September 2025

Proscan PRCD386 Manual

29 September 2025

Reflexion PS25BT Manual

29 September 2025