Sonance Visual Performance VP69 Manual

Sonance Højttaler Visual Performance VP69

Læs gratis den danske manual til Sonance Visual Performance VP69 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Sonance Visual Performance VP69, eller vil du spørge andre brugere om produktet?

Side 1/4
Introduction
Thank you for purchasing Sonance Visual Performance®
Series Medium rectangle speakers. When properly installed your
new speakers will give you years of entertainment pleasure.
Box Contents
Each Sonance Visual Performance Series Medium rectangle
speaker box contains (2) Visual Performance Series speakers,
(2) paint plugs (installed on the fronts of the speakers),
(2) paintable grilles and (1) mounting cut-out template.
Speaker Placement
Home Theater Speaker Placement
Left, Center & Right Speakers
Place the left & right speakers on either side of the video
screen, 6 10 feet (1.8m 3m) apart and 3 4 feet
(0.9m 1.2m) from the floor.
If possible, locate the center speaker at the same height as the
left & right channel speakers.
If you must place the center speaker above or below a video
screen, place it no more than 2 feet (0.6m) above or below the
center of the left and right speakers. This will maintain consis-
tent tonality between all three front channel speakers.
The main listening position should be 8 12 feet
(2.4m 3.7m) away from the speakers.
Use
Figure 1
as a guide.
Surround Speakers (5.1-Channel System)
Locate the surround channel speakers on the side walls 2 6 feet
(0.6m 1.8m) behind the listening position, 5 7 feet
(1.5m 2.1m) from the floor. Use
Figure 2
as a guide.
Surround Speakers (7.1-Channel System)
LEFT & R : Place the left and right IGHT SURROUND PEAKERSS
surround speakers directly to the sides of the listening position,
at least 5 feet from the floor.
SURROUND PEAKERSBACK S : Place the surround back speakers in
the rear wall, 3 6 feet (0.9m 1.8m) apart and 5 7 feet
(1.5m 2.1m) from the floor.
Use
Figure 3
as a guide.
I N S T R U C T I O N M A N U A L
V I S U A L P E R F O R M A N C E ® S E R I E S
M E D I U M R E CTA NGL E S P E A K E R S
S W :AFETY ARNING
THESE SPEAKERS HAVE AST OUNTF M ®TABS T HAT PREVENT T HE
SPEAKER FROM FALLING OUT OF THE MOUNT ING HOLE DURING THE
INSTALLATION PROCESS.
T F MH E E DG E S O F T H E A S T O U NT TA B S A R E V E RY S H A R P.
US E CA U T I ON W HE N H A ND L I N G T H E S P E A K E R.
18"
(0.5m)
From Side
Wall
18"
(0.5m)
From Side
Wall
2'
(0.6m)
max.
6' – 10'
(1.8m – 3m)
Apart
FIGURE 1: LEFT, C & RENTER IGHT HANNELC
H TOME HEATER PEAKER LACEMENTS P
5' – 7'
(1.5m – 2.1m)
2' – 6'
(0.6m – 1.8m)
F H T S SIGURE 2: 5.1-CHANNEL OME HEATER URROUND PEAKER
PLACEMENT
Right Surround
Speaker
Left Surround
Speaker
Left
Front
Speaker
Right
Front
Speaker
Video
Screen
Center
Speaker
Left
Surround Back
Speaker
Right
Surround Back
Speaker
F H T S PIGURE 3: 7.1-CHANNEL OME HEATER PEAKER LACEMENT
2
SONANCE VISUAL PERFORMANCE®MEDIUM RECTANGLE
Stereo (2-Channel) Placement
Place the left and right speakers 6 10 feet (1.8m 3m) apart,
with the main listening position as close to midway between
the speakers as possible.
The speakers should be at least 2 feet (0.6m) away from the
side walls.
The main listening position should be 4 10 feet (1.2m 3m)
away from the speakers.
In most cases pivoting the tweeter of each speaker directly
towards the main listening position will help maximize the
stereo soundstage.
Use the left and right speaker placement in
Figure 1
, on page 1,
as a guide.
Before Installation: Retrofit
1. Determine the location for the speaker (see
Speaker Placement
on page 1).
2. Perform an obstruction survey to be certain that there are no
studs, conduit, pipes, heating ducts, pocket doors or air returns
in the wall cavity that will interfere with the speaker.
3. Mounting space requirements:
Mounting space req uirements:
Mounting space req uirements:
Mounting space req uirements:Mounting space req uirements: 61516 (176mm) wide by
10¾ (273mm) high cut-out and at least 3½ (89mm) mount-
ing depth. Medium ThinLine rectangle speakers require at
least 2½ (64mm) mounting depth.
4. Position the included cut-out template where the speaker is to
be located and pencil an outline on the wall. If you are unsure
about obstructions, drill a small hole in the center of the
outline and insert a coat hanger wire into the hole to feel-
around for possible obstructions.
5. Cut the mounting hole using a keyhole or drywall saw, and
run the speaker wires from the mounting hole to the amplifier
location.
NOT E : CO NSU LT LOC AL B U IL DI NG C OD E S B E FOR E R U N NI NG
SP E AK E R W IR E S TH ROU G H W AL LS.
Before Installation: IR Plug
Sonance Visual Performance Series
Medium rectangle speakers have a
plug for installing an IR receiver into
the speaker’s front baffle (see
Figure
4
). In systems where the electronics
are placed in an inconvenient loca-
tion this allows remote controls to be
aimed at the front of the room instead
of at the electronics.
The IR plug is in the form of a bolt
and retaining nut. To remove the
plug, unscrew the nut (located behind
the baffle, see
Figure 5
) and remove
the bolt. The hole is designed to
receive a Sonance OptiLinQ®SMR1
or SMR1P Surface-Mount IR receiver.
Insert the IR receiver through the
front of the speaker baffle and use
the nut included with the receiver to
secure it to the baffle.
Installation
Sonance Visual Performance Series speakers feature exclusive
FastMount tabs and an integral Roto-Lock®mounting system for
quick mounting directly into existing walls.
WA R N I NG : T HE E D GE S O F T HE FA S T M OU N T TA B S
ARE VERY SHARP. USE CAUTION WHEN HANDLING
T HE S P E A K E R.
1. Remove the paint plug from the speaker.
2. Strip ¼ ½ (6mm 12mm) of insulation from each speak-
er lead. Twist the strands or tin the exposed wire with solder
to ensure that there are no stray strands. (Stray strands that
touch each other can cause a short-circuit that can damage
the amplifier.)
3. The speakers connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts.
The speaker’s positive
post is labeled with a
red dot; the negative
post is labeled with a
black dot. Double-check
that you connected
amplifier + to speaker
+ and amplifier to
speaker .
4. Make sure all the Roto-
Lock clamps are retract-
ed so that they are
tucked within the mount-
ing hole’s border. Insert
the speaker into the hole
in the wall (
Figure 6
).
The Roto-Lock system
can accommodate a
maximum wall material
thickness of 1¼
(32mm).
The FastMount tabs will
prevent the speaker from
falling out of the mount-
ing hole, allowing you to
let go of the speaker to
pick-up tools or other
items (
Figure 7
).
N FOTE: THE ASTMOUNT TABS
ARE DESIGNE D F OR ONE -
TI M E U S E ON LY. IF THE
SPEAKE R IS R EM OVE D FR OM
TH E MO U NTI NG H OL E TH E
F MA S T O U N T TA B S W I L L
DISCON NE CT A ND REM AIN
IN SIDE THE WALL.
Roto-Lock Clamp
(retracted)
Roto-Lock Clamp
(retracted)
F SIGURE 6: INSERTING THE PEAKER
INTO THE OUNTING OLEM H
FastMount
Tabs
Roto-Lock Clamps
(retracted)
FIGURE 7: FAST OUNTM TABS AND
R -L COTO OCK LAMPS
FIGURE 4: IR PLUG
FIGURE 5: IR PLUG
RETAINING UTN
IR Plug
Retaining Nut


Produkt Specifikationer

Mærke: Sonance
Kategori: Højttaler
Model: Visual Performance VP69

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonance Visual Performance VP69 stil et spørgsmål nedenfor, og andre brugere vil svare dig