Sony SNC-EM602R Manual

Sony Overvågningskamera SNC-EM602R

Læs gratis den danske manual til Sony SNC-EM602R (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Sony SNC-EM602R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

LAN port

LAN cable holder

c-1

85.7 (3

/ )8

46 (1

/ )16

85.7 (3 3/ )8

83.5 (2 9/ )32

Hole for

connecting

cables

ø73 (2

/ )8

Horizontal

marker

Hole for

installing

the bracket

Vertical marker

Unit: mm (inches)

Wrench

Screw (4 positions)

3, 4

Ceiling

Bracket (supplied)

Locating pin

Groove

Wire rope (supplied)

ScrewM4×8

(supplied)

Holder

Camera unit mounting

screw (supplied) (4)

4-473-809- (1)11

Printed in China

Network Camera

SNC-EM602R/EM632R

Installation Manual

Before operating the unit, please read this manual thoroughly and

retain it for future reference.

About the Manuals

Installation Manual (this document)

This Installation Manual describes the names and functions of parts and controls

of the Network Camera, gives connection examples and explains how to set up

the camera. Be sure to read the Installation Manual before operating.

SNC easy IP setup Guide (stored in the CD-ROM)

User’s Guide/Application Guide (Web)

The User’s Guide describes how to set up the camera and how to control the

camera via a Web browser.

After installing and connecting the camera correctly, operate referring to this

User’s Guide.

Using the Software

The supplied CD-ROM includes the setup program for assigning an IP address.

The information for how to set up an IP address is also included in the disc in PDF

format.

User’s Guide and Application Guide can be downloaded from the disc, or the

following URL:

http://www.sony.net/ipela/snc

Using the CD-ROM manual

The manual can be read on a computer with Adobe Reader installed.

You can download Adobe Reader free from the Adobe website.

1 Open the index.html file in the CD-ROM.

2 Select and click on the manual that you want to read.

Note

If you have lost or damaged the CD-ROM, you can purchase a new one from your

Sony dealer or Sony service counter.

Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the

United States and/or other countries.

Assigning the IP address

Assign the IP address using the setup program in the supplied CD-ROM.

For details on how to set up the IP address, see SNC easy IP Setup Guide.

Location and Function of Part

The figure shows the camera without the dome casing.

Side 



Wiring slit

Feed the wire rope through this.

For details, see “Installing the Camera.”



Base (PAN)



Camera block



Lens



LAN cable (RJ-45) (supplied and connected to the camera at the

factory)

Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX

network using a commercially available network cable (UTP, category 5).



Side conduit hole (

/4 inches NPT or M27 (2.0 mm (

/32 inches)-

pitched))

Connect a pipe to this hole. There is a conduit hole on the side of the camera

unit. The conduit hole cover is installed in the side conduit hole at the factory.

Remove the cover as needed and connect the pipe to the hole.

Note

Take care not to trap the cables between the camera and the ceiling or the wall. If

the cable is trapped, it may cause a fire or electric shock due to breaking.



Camera head

Inside 



Camera unit



ZOOM/FOCUS switch

Use this switch to adjust lens’ zoom and focus. Slide the switch lever to select the

desired function.

[W] WIDE: Zoom out

[T] TELE: Zoom in

[N] NEAR: Focus on a nearby subject

[F] FAR: Focus on a distant subject

Hold down the center of the ZOOM/FOCUS switch for a moment to focus

automatically.



Camera unit mounting screws (four positions)

Make sure to tighten the screws securely when installing the camera.



MONITOR output jack

Connect this jack to a video input connector of a video monitor. You can adjust

the camera or lens while looking at the image on the video monitor. After

adjusting the camera or lens, disconnect the cable.



Camera block fixing screws (tilt) (two positions)

Firstly, loosen the screws and point the camera block in the desired direction,

then tighten the screws to secure in place.



Nut (

¾ inches NPT or M27 (2.0 mm (

/32 inches)-pitched))



Safety cord

This cord prevents the dome casing from falling off the unit.



TOP mark

Indicates the image direction.



LAN network port (RJ-45)

Connect a commercially available network cable (UTP, category 5) to

communicate with a network or PoE/PoE+* system.

For details on connection, see the Instruction Manual of the power supply

equipment.

(*PoE/PoE+ stands for Power over Ethernet. It is pursuant to IEEE802.3at.)



Dome casing

The dome cover is made of polycarbonate. A waterproof rubber gasket is

provided on the joint surface to the unit.



POWER indicator (Green)

When the power is supplied to the camera, the camera starts checking the

system. If the system is normal, this indicator lights up.



HEATER indicator (Green)

The indicator lights up in green when the built-in heater is working normally.



NETWORK indicator (Green/Orange)

The indicator lights up or flashes when the camera is connected to the network.

The indicator is off when the camera is not connected to the network.



Reset switch

To reset the camera to the factory default settings, hold down this switch with a

point and supply the power to the camera.



Mode setting DIP switches

DIP switch function/settings

PIN No. Switch

Location

Up(ON) Down(OFF)

1 VIDEO PAL NTSC

2 HEATER EN

1 VIDEO (NTSC/PAL) switch (Initial setting: NTSC)

Switches the video output.

After setting the switch, reboot the camera unit.

2 HEATER (Heater EN/EN) switch (Initial setting: EN)

Enable (EN)/Disable (EN) the built-in heater.

Note

When power is supplied by IEEE802.3af (PoE) equipment, set the HEATER (Heater

EN/EN) switch to EN to disable the heater on the camera; otherwise, the camera

will not work properly.

Bottom 



LAN cable holder (supplied and connected to the camera at the

factory)

Packing for waterproofing the cables.



Holder plate

Fixes the cable holder.



GND

Ground the camera when you install it.

Note

Use the supplied Screws (M4 × 8)



Holder plate fixing screws (three positions)

Fixes the holder plate.



Rating label

Shows the name of this camera and its electric rating.

Preparations

Change connections and cable wiring 

All the supplied cables are connected to the camera at the factory.

To change connections and cable wiring to suit your requirements, perform the

following steps.

When you route the cables from the side of the camera unit, see “Connecting to

the side conduit hole”.

a) If you use the camera with its factory setting

The preparation is completed.

b) If you use your own LAN cable

1 Loosen the four screws of the dome casing using the supplied wrench and

remove the dome casing.

2 Loosen the three holder plate fixing screws on the bottom to remove the

holder plate and LAN cable holder.

3 Disconnect the LAN cable (connected at the factory) from the LAN port and

remove it from the LAN cable holder

4 Insert your LAN cable through the hole of the LAN cable holder.

5 Insert the LAN cable through the bottom hole and adjust the length of the

LAN cable from the hole to the LAN port.

6 Connect the LAN cable to the LAN port.

7 Attach the removed holder plate to the bottom hole with the three holder

plate fixing screws.

Notes

For case b), keep your LAN cable diameter

ø5.0 mm (

/32 inches) - ø6.0 mm

(

/4 inches). Otherwise, waterproof the bottom hole.

If you need to waterproof the camera, see “Important precautions” overleaf.

Do not pull on any cables forcefully, as a connection may become loose.

c) Connecting to the side conduit hole

The LAN cable is connected to the camera through the bottom hole at the

factory. If you want to use the side conduit hole, perform the following steps:

1 Remove the conduit hole cover.

2 Loosen the three holder plate fixing screws on the bottom to remove the

holder plate and LAN cable holder.

3 Disconnect the LAN cable from the LAN port, and pull it out through the

bottom hole.

4 Insert the LAN cable through the pipe, then through the supplied cable

holder (for conduit), and finally through the side conduit hole. ( -c-1)

5 Connect the LAN cable to the LAN port.

6 Screw the removed conduit hole cover into the bottom hole.

Notes

If the bottom hole is dirty, the conduit hole cover cannot be fixed firmly. In this

case, moisture may leak into the casing and this may cause a malfunction.

Wipe off the dust with a soft cloth, and fix the conduit hole cover firmly.

Cover the joint part of the pipe/cover with silicon sealant, etc. to prevent

moisture from getting inside the casing.

The holder plate and the cable holder are not necessary when you attach the

conduit hole cover to the bottom hole.

Be careful not to drop the conduit hole cover and nut (

-6) when installing or

removing the camera.

For details on using the supplied cable holder (for conduit), see “Important

precautions” overleaf.

Installation

WARNING

If you attach the camera in the height such as the wall or the ceiling, etc.,

entrust the installation to an experienced contractor or installer.

If you install the camera at a height, ensure that the installation location and

its material are strong enough to withstand a weight of 15 kg (33 lb 11 oz) or

more, and then install the camera securely. If the ceiling is not strong enough,

the camera may fall and cause serious injury.

To prevent the camera from falling, make sure to attach the supplied wire rope.

If you attach the camera to the ceiling, check periodically, at least once a year,

to ensure that the connection has not loosened. If conditions warrant, make

this periodic check more frequently.

Deciding the Installation Location of the Camera 

After deciding the direction in which the camera will shoot, make the required

hole (ø73 mm (2

/ inches)) for the connecting cables using the supplied 8

template. Then decide the four mounting hole positions to install the bracket.

Mounting screws

The supplied bracket is provided with eight ø4.5 mm (

/ inches) mounting 16

holes. Install the bracket on a ceiling or wall with screws through four mounting

holes: two 83.5 mm (3

/ inches)-pitched holes or four 85.7 mm (3 32

/ inches)-8

pitched holes. The required mounting screws differ depending on the installation

location and its material. (Mounting screws are not supplied.)

Steel wall or ceiling: Use M4 bolts and nuts.

Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be

15 mm (

/ inches) or more.8

Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.

Junction box: Use screws to match the holes on the junction box.

WARNING

The required mounting screws differ depending on the installation location and

its material. If you do not secure the camera with the appropriate mounting

screws, the camera may fall off.

Installing the Camera 

Remove the dome casing.

 Loosen the screws with the wrench (supplied).

 Pull up and remove the dome casing. When the screw catches on the

screw hole, pull up the screw.

2 Install the supplied bracket on the ceiling or wall.

Refer to “Mounting screws” for screws to be used.

3 Fix the supplied wire rope to the camera unit and the ceiling or wall.

 Fix the wire rope with the supplied Screw M4 

× 8 to the hole for the

wire rope on the bottom of the camera unit.

 Fix the wire rope to the ceiling or wall.

When you install the camera on a wall, feed the cables through one of the

wiring slits. ( -1)

4 Attach the camera unit to the bracket with the supplied four camera unit

mounting screws.

The screws have a fall-prevention mechanism. The screws inserted into the

screw holes of the camera unit do not fall even if you turn the camera unit

upside down.

Insert the two holders to any two of the four grooves on the bracket.

Turn the camera clockwise until the locating pins snap to the holes on the

holders. Then the four camera installation holes will align the projections on

the bracket accordingly. There are four projections with an angle of

90 degrees, so you can select one of four directions.

Then tighten the four camera unit mounting screws to attach the camera unit

to the bracket through the camera installation holes.

Note

If you cannot use screws on a ceiling or wall, or if you want to make the camera

less conspicuous, use the YT-ICB45 in-ceiling bracket (optional) with which you

can mount the camera on the ceiling.

For this model, install the camera to the position on the side brackets of 

YT-ICB45. Refer to the Installation Instructions of YT-ICB45 for detail information.

(continued overleaf)

Produkt Specifikationer

Mærke:	Sony
Kategori:	Overvågningskamera
Model:	SNC-EM602R
Kode for international beskyttelse (IP):	IP66
Type:	IP-sikkerhedskamera
Vægt:	1580 g
Brugervejledning:	Ja
Produktfarve:	Hvid
Formfaktor:	Kuppel
Understøttede videotilstande:	720p
Opbevaringstemperatur (T-T):	-20 - 60 °C
Relativ luftfugtighed ved drift (H-H):	20 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	20 - 95 %
Format til analogt signal:	NTSC, PAL
Ethernet LAN:	Ja
Understøttede videoformater:	H.264
Driftstemperatur (T-T):	-10 - 50 °C
Maksimal opløsning:	1280 x 1024 pixel
Understøttede grafikopløsninger:	320 x 240,352 x 288,704 x 576,720 x 480,720 x 576,1280 x 768,1280 x 960,1280 x 1024 (SXGA),1280 x 720 (HD 720),640 x 480 (VGA),800 x 600 (SVGA)
Kabelteknologi:	10/100Base-T(X)
Understøttede netværksprotokoller:	IPv4, TCP, UDP, ARP, ICMP, IGMP*1, HTTP, DHCP, DNS, NTP, RTP/RTCP, RTSP over TCP, SMTP over HTTP, IPv6, HTTPS, SNMP (v1, v2c, v3), SSL
Strømkilde type:	PoE
Monteringstype:	Loft
Understøttet placering:	Udendørs
Understøttede Windows-operativsystemer:	Ja
Hvidbalance:	ATW, Fluorescent, Manual
Sensortype:	CMOS
Samlet antal megapixels:	1.3 MP
Optisk zoom:	3 x
Digital zoom:	4 x
Hældningsvinkelområde:	-7 - 75 °
Progressiv scanning:	Ja
Strøm over Ethernet (PoE):	Ja
Bredt dynamikområde (WDR):	Ja
Minimumsbelysning:	0.5 Lux
Panoreringsområde:	-192 - 192 °
Rotationsvinkel:	198 °
Optisk sensorstørrelse:	1/3 "
Zoom kapacitet:	Ja
Nattesyn:	Ja
Bevægelsessensor (video):	Ja
Monteringssæt:	Ja
Brændviddeområde:	3 - 9 mm
Signal/støjforhold:	50 dB
Monteringsbeslag inkluderet:	Ja
Minimum systemkrav:	Windows XP (32 bit) Professional Edition\r\nWindows Vista (32 bit) Ultimate, Business Edition\r\nWindows 7 (32/64 bit) Ultimate, Professional Edition\r\nWindows 8 Pro (32/64 bit)\r\nMicrosoft DirectX 9.0c or higher\r\n\r\nProcessor Intel Corei7 2.8 GHz or higher\r\nMemory 2 GB or more
PTZ-kontrol:	Ja
Minimum processor:	Corei7 2.8 GHz or higher
Opdagelsesafstand:	300 m
Aktiv manipulering af alarm:	Ja