Soundskins SSK-BRONCO4DR Manual
Soundskins
Ikke kategoriseret
SSK-BRONCO4DR
Læs nedenfor 📖 manual på dansk for Soundskins SSK-BRONCO4DR (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 20 personer og blev bedømt med 4.3 stjerner i gennemsnit af 10.5 brugere
Side 1/2
Bronco Kit Door Installation Instructions
1. Start by locating the fastening hardware on the door panels.
There will be one behind the door handle under a plastic cover,
one behind the door grab handle that you will have to pop out
to reveal, and 2 at the bottom right corner of the door panels.
Take a 7 mm socket and remove. Then, use a panel tool to pry
the panel off the door, start from the bottom right corner. Be
sure not to break any clips or mounting hardware.
3. Now, apply the door pieces. Peel off the backing paper
starting at the top, tack the piece onto the door and work your
way down, pressing down the material and pulling down the
backing paper more as you go along. Feed the harnesses
through the proper holes and ensure everything is aligned
before pressing the entire piece down. Repeat steps 1-3 for all
doors. Then replace your door panels and reconnect the wires
and enjoy your quiet new ride!
2. Pull the door panel away slowly. There will be 2 plug clips
that will need to be released as well as a wire plug to
disconnect. Set the door panel aside and unhook all plugs,
remove the vapor barrier, and clean the car metal surface
using a microfiber cloth and Acetone or other cleaning solution.
The point is to get the surface clean to ensure material glue
contact.
Soundskins USA
13452 Alondra Blvd, Cerritos, CA 90703
Phone: 877.211.5597
Email: team@soundskinsglobal.com
www.SoundSkinsGlobal.com
R
• 7mm socket
• Socket extension
• Panel /trim tool
• Roller
• Microber cloth
• Acetone or cleaning solution
Tools needed for installation: Scan this code to watch the
full instructional video!
4 Piece Custom Cut PRO KIT
2021+
Recommended Installation Instructions
A. Prepping the Surface
After removing interior door panels, you are ready to clean the metal areas that will be insulated. If the metal has a
“new” look without imperfections, then take a microfiber cloth and wipe away any dust and debris. If the metal is
showing signs of age like rust, we recommend using Acetone with a breathing mask to wipe off debris and loose
particles. A shop vacuum might be needed to remove loose debris on the floorboard.
B. Installing Panels
Now that you have a clean surface, you are ready to start applying the sheets. We recommend using a roller to
release air pockets that might be lingering from trapped air. You want to make sure that you have rolled those out to
the edge and all the material has a good seal to the metal surface. Make sure all pieces are installed and inspected
before reinstalling the interior.
1) Driver Front Door Panel 2) Driver Rear Door Panel
3) Passenger Front Door Panel 4) Passenger Rear Door Panel
1
2
3
4
Produkt Specifikationer
| Mærke: | Soundskins |
| Kategori: | Ikke kategoriseret |
| Model: | SSK-BRONCO4DR |
Har du brug for hjælp?
Hvis du har brug for hjælp til Soundskins SSK-BRONCO4DR stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Soundskins Manualer
12 Marts 2025
12 Marts 2025
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
1 September 2024
Ikke kategoriseret Manualer
- Ikke kategoriseret Kenton
- Ikke kategoriseret Hugo Muller
- Ikke kategoriseret Life Fitness
- Ikke kategoriseret Hellberg
- Ikke kategoriseret StarIink
- Ikke kategoriseret Hori
- Ikke kategoriseret Nintendo
- Ikke kategoriseret A-Designs
- Ikke kategoriseret HK Audio
- Ikke kategoriseret HUANUO
- Ikke kategoriseret Leotec
- Ikke kategoriseret Rolly Toys
- Ikke kategoriseret Atlantis Land
- Ikke kategoriseret Apelson
- Ikke kategoriseret Redrock Micro
Nyeste Ikke kategoriseret Manualer
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025