SoundTube RS62-EZ-WH Manual

SoundTube Højttaler RS62-EZ-WH

Læs gratis den danske manual til SoundTube RS62-EZ-WH (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om SoundTube RS62-EZ-WH, eller vil du spørge andre brugere om produktet?

Side 1/4
Box contents
© 2016 SoundTube Ente tainment, Inc. r All rights rese ved.r INS_RS-EZ 9-22-2016 - EN54
Document Reference Number RSEZ0013
RS-EZ series
Speaker
Cover Plate
Cover Plate
Screws (4)
Hanging Hardware
Hanging Bracket
Terminal
Block
Weather plug
1 Speaker
1 Cover Plate w/ 4 screws
1 Rubber weather plug
1 Hanging kit
1 3/8” NPT Wire Gland
1 3/4” to 3/8” NPT Adapter
Install Instructions For:
RS42-EZ-WH, RS42-EZ-BK, RS62-EZ-WH & RS62-EZ-BK
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
1. Unpack speaker and
SpeedClamp™ mounting
hardware.
2. Thread hanging or safety
cable through SpeedClamp™
mechanisms as shown.
3. Attach the hanging cable
by securing it and safety
cable to structure as
shown.
4. Thread cable end(s)
through SpeedClamp™
mechanisms as shown.
9. Connect signal wires to
(+) and (-) inputs. Use extra
(+) and (-) for daisy
chaining.
11. Place cover plate onto
top of speaker and rotate
clockwise until alignment
indicators meet.
12. Tighten all four (4) screws
to lock cover plate in place.
5.
7a. Attach hanging cable
by (1) inserting into side of
mounting bracket and (2)
rotating to align with center
slot in hanging bracket.
6. Slide cover plate over
hanging and safety cables
and run signal wire through
center hole.
10. Select desired tap
position. Switch is preset to
maximum 70.7V (100V)
mode.
7b. Once aligned with central
slot, pull cable up into slot to
secure. Repeat steps 7a and
7b with secondary safety ca-
ble into one of the side slots.
Adjust speaker hanging
height with SpeedClamp™
mechanism. Pull to tighten &
press button on SpeedClamp
as shown to loosen or adjust.
13. Install rubber weather
plug by sliding slit over the
wire, then pressing snuggly
into hole in cover plate.
14. Done.
8. Extra slot and 2 holes
provided for additional
safety cables where
needed.
1.
2.
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
Install Instructions For:
RS42-EZ-WH, RS42-EZ-BK, RS62-EZ-WH & RS62-EZ-BK
RS-EZ series


Produkt Specifikationer

Mærke: SoundTube
Kategori: Højttaler
Model: RS62-EZ-WH

Har du brug for hjælp?

Hvis du har brug for hjælp til SoundTube RS62-EZ-WH stil et spørgsmål nedenfor, og andre brugere vil svare dig