Sun Joe 24V-HCS-4-LTE Manual

Sun Joe Ikke kategoriseret 24V-HCS-4-LTE

Læs gratis den danske manual til Sun Joe 24V-HCS-4-LTE (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Sun Joe 24V-HCS-4-LTE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

A Division of Snow Joe, LLC

OPERATOR’S MANUAL

Model 24V-HCS-4-LTE Form No. SJ-24V-HSC-4-LTE-880E-M

CORDLESS PRUNING SAW

24V MAX* | 2.0 Ah | 4-INCH

*DISCLAIMER: Initial no-load voltage, when fully charged,

peaks at 24V; nominal voltage under typical load is 21.6V.

SAVE THESE INSTRUCTIONS

Original instructions.

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, ﬁre and/

or serious injury. Save all warnings and instructions for future

reference.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in serious injury or death.

mWARNING! This indicates a hazardous situation, which, if

not avoided, could result in serious injury or death.

mCAUTION! This indicates a hazardous situation, which, if

not avoided, could result in minor or moderate injury.

Intended Use

This cordless pruning saw was designed and manufactured for

trimming and pruning tree limbs and branches and for cutting

smaller logs not to exceed a max. cut of 3.5 in. (8.9 cm) in

diameter depending on the type of wood. All of the wooden

objects intended to be cut with this pruning saw should be no

thicker than the guide bar's maximum cutting capabilities.

Any other use diﬀering from the above mentioned applications

poses a serious hazard to the user and may damage both the

tool and your personal property. Improper use of the machine

will invalidate the warranty and relieve the manufacturer from all

liabilities. The user will consequently be liable for all and any

damage or injury to himself/herself or others.

General Power Tool Safety

Warnings

mWARNING! Read all safety warnings, instructions,

illustrations and speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁre and/or serious injury. Save all warnings and

instructions for future reference.

Work Area Safety

1. Keep work area clean and well lit – Cluttered or dark areas

invite accidents.

2. Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust – Power tools create sparks which may ignite the dust

or fumes.

3. Keep children and bystanders away while operating a

power tool – Distractions can cause you to lose control.

Electric Safety

mWARNING! Do not expose a battery pack or appliance

to ﬁre or excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may cause explosion.

1. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools – Unmodified plugs and

matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators – There

is an increased risk of electric shock if your body is earthed

or grounded.

3. Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts – Damaged or

entangled cords increase the risk of electric shock.

4. When operating a power tool outdoors, use an extension

cord suitable for outdoor use – Use of a cord suitable for

outdoor use reduces the risk of electric shock.

5. If operating a power tool in a damp location is

unavoidable, use a RESIDUAL CURRENT DEVICE (RCD)

protected supply – Use of an RCD reduces the risk of

electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the inﬂuence of drugs,

alcohol or medication – A moment of inattention while

operating power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear

eye protection – Protective equipment such as a dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will

reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the

oﬀ-position before connecting battery pack, picking up

or carrying the tool – Carrying power tools with your finger

on the switch or energizing power tools that have the switch

on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on – A wrench or a key left attached

to a rotating part of the power tool may result

in personal injury.

5. Do not overreach. Keep proper footing and balance at

all times – This enables better control of the power tool in

unexpected situations.

6. Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts – Loose clothes, jewelry or long hair can be caught in

moving parts.

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used – Use of dust collection can

reduce dust-related hazards.

8. Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool safety

principles. A careless action can cause severe injury within

a fraction of a second.

Power Tool Use and Care

1. Do not force the power tool. Use the correct power tool

for your application – The correct power tool will do the job

better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it

on and oﬀ – Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

3. Disconnect the battery pack from the power tool before

making any adjustments, changing accessories, or

storing power tools – Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

4. Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool – Power tools are

dangerous in the hands of untrained users.

5. Maintain Appliance With Care – Keep cutting edge sharp

and clean for best performance and to reduce the risk of

injury. Follow instructions for lubricating and changing

accessories. Inspect appliance cord periodically, and

if damaged, have it repaired by an authorized service

facility. Inspect extension cords periodically and replace

if damaged. Keep handles dry, clean, and free from oil and

grease.

6. Check Damaged Parts – Before further use of the

appliance, a guard or other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other condition

that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced by an

authorized service center unless indicated elsewhere in this

manual.

7. Use the power tool, accessories etc. in accordance

with these instructions, taking into account the working

conditions and the work to be performed – Use of the

power tool for operations different from those intended could

result in a hazardous situation.

8. Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

Battery Tool Use and Care

mWARNING! Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

1. Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

2. Use appliances only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

3. When the battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

4. Under abusive conditions, liquid may be ejected from the

battery; avoid contact. If contact accidentally occurs, flush

with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or

burns.

5. Do not use a battery pack or appliance that is damaged

or modified. Damaged or modified batteries may exhibit

unpredictable behavior resulting in fire, explosion or risk of

injury.

6. Do not expose a battery pack or appliance to fire or

excessive temperature. Exposure to fire or temperature

above 104°F (40.5°C) may cause explosion.

7. Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature range

specified in the instructions. Charging improperly or at

temperatures outside of the specified range may damage the

battery and increase the risk of fire.

8. Do not modify or attempt to repair the appliance or the

battery pack (as applicable) except as indicated in the

instructions for use and care.

Produkt Specifikationer

Mærke:	Sun Joe
Kategori:	Ikke kategoriseret
Model:	24V-HCS-4-LTE

Har du brug for hjælp?

Hvis du har brug for hjælp til Sun Joe 24V-HCS-4-LTE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Sun Joe Manualer

Sun Joe 24V-HCS-4-LTE Manual

7 Januar 2025

Sun Joe SPX-PWB1 Manual

7 Januar 2025

Sun Joe 24VBAT-XR8 Manual

6 Januar 2025

Sun Joe SJFP30 Manual

6 Januar 2025

Sun Joe SBJ6-GA Manual

6 Januar 2025

Sun Joe GGNP-S3 Manual

6 Januar 2025

Sun Joe SJ-APS-022 Manual

6 Januar 2025

Sun Joe 24VBAT-XR12 Manual

6 Januar 2025

Sun Joe 24V-BBQ-CT Manual

18 September 2024

Sun Joe WA24C-LTE-RM Manual

10 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

OmniMount POWER40 Manual

17 Juni 2025

OmniMount OL50FT Manual

17 Juni 2025

Intermatic FD30MHW Manual

17 Juni 2025

Toorx SRX-EVOLVE Manual

17 Juni 2025

OmniMount WorldMount 2N1-L Manual

17 Juni 2025

OmniMount WorldMount 4N1-L Manual

17 Juni 2025

Intermatic FD60MC Manual

17 Juni 2025

Microchip MPFS160TLS Manual

17 Juni 2025

Hughes & Kettner Metal Master Manual

17 Juni 2025

Hansgrohe AXOR Montreux 16516310 Manual

17 Juni 2025