SurgeX PF-420 Manual

SurgeX Vægudtag PF-420

Læs gratis den danske manual til SurgeX PF-420 (2 sider) i kategorien Vægudtag. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om SurgeX PF-420, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SurgeX

Installation Instructions

PF-420

Mounting

The SurgeX PF420 is designed to be mounted on a flat, vertical surface. Secure the

unit by fastening at the corners with appropriate screws. This product must not be

flush mounted or set between wall studs as overheating can occur under such

conditions. Use caution when removing knock-outs so that damage does not occur

to internal components.

Connection

The SurgeX PF420 provides four identical circuits, each rated at 120 Volts and 20

Amps, providing a total capacity of 80 Amps. This product shall be wired only by

qualified Electricians using 12 AWG conductors as specified in Article 310 of the

2005 National Electric Code, as set forth in Table 310.13. Any type of conductor

suitable for use in wet or dry locations such as (but not limited to) THHN, THHW,

THW, THWN, or TW shall be considered acceptable if local Code permits. Each

circuit must be protected by a 20 Amp circuit breaker.

A special terminal is provided for each circuit to carry an Isolated Ground

(technical ground) though the unit. These terminals have no connection to the

chassis ground or to the unit itself and their sole purpose is to provide a convenient

way of joining isolated ground wires.

The four higher terminal blocks are for the Line connections, with the

corresponding Load terminal block for that circuit directly below it.

Line Connection

Connect the electrical service from the load side of the circuit breaker to the upper

terminal block as follows:

 Live (Black) wire to the terminal labeled “LINE”

 Neutral (White) wire to the terminal labeled “NEUT”

 Ground (Green) wire to the terminal labeled “GRND”

 Isolated Ground wire (if used) to the terminal labeled “ISO GND”

Load Connection

Connect the equipment circuit (load) to the lower terminal block as follows:

 Live (Black) wire to the terminal labeled “LOAD”

 Neutral (White) wire to the terminal labeled “NEUT”

 Ground (Green) wire to the terminal labeled “GRND”

 Isolated Ground wire (if used) to the terminal labeled “ISO GND”

Indicator Light

There are four green indicator lights on the front of the unit, one for each circuit.

These green lights are Self-Test indicators that indicate power is applied to the unit

and also that the internal surge protection circuitry on each circuit is fully

functional.

Produkt Specifikationer

Mærke:	SurgeX
Kategori:	Vægudtag
Model:	PF-420

Har du brug for hjælp?

Hvis du har brug for hjælp til SurgeX PF-420 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vægudtag SurgeX Manualer

SurgeX PF-420 Manual

8 September 2025

Vægudtag Manualer

Nyeste Vægudtag Manualer

Heitronic MINIMO Manual

8 September 2025

Schwaiger LAD260 Manual

6 September 2025

Schwaiger SOAW0044 Manual

6 September 2025

Savio LZ-10 Manual

4 September 2025

Kogan KASMPLGOD2A Manual

29 August 2025

Extron DTP T HWP 232 D Manual

28 August 2025

Extron FOX T UWP 302 MM Manual

28 August 2025

V-TAC VT-5002 Manual

28 August 2025

Extron FOX T UWP 302 SM Manual

27 August 2025

V-TAC VT-1112-3 Manual

27 August 2025