Sussex RWBMS150RH Manual

Sussex Kran RWBMS150RH

Læs gratis den danske manual til Sussex RWBMS150RH (2 sider) i kategorien Kran. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Sussex RWBMS150RH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003

Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c

5.5

litres per

minute

Licence No. 0124

In accordance with AS/NZS 6400

Sussex Taps Pty Ltd

WATER RATING

www.waterrating.gov.au

The more

stars the more

water efcient

NOGGIN

Finished

Wall Surface

56mm

Dress

Ring

Manifold

Apply Silicone

SET

SCREW

HANDLE

BODY

Stud Face

NOGGIN

Dress Ring

Masterﬁt

Stud Face

Finished

Wall Surface

Bath Outlet

Product code

Circa

RWBMS150RH Wall basin mixer system 150mm

RWBMS200RH Wall basin mixer system 200mm

RWBMS250RH Wall basin mixer system 250mm

RWBMS150RH-V Wall basin mixer system 150mm - Vertex

RWBMS200RH-V Wall basin mixer system 200mm - Vertex

RWBMS250RH-V Wall basin mixer system 250mm - Vertex

Wall basin mixer system Dress kit

Mixer dress kit

Outlet fit off

- Remove Mixer protective cover.

- Using silicone, seal the wall surface around the Mixer and

Outlet threads.

- Ft the Mixer Dress Ring.

- Fit the Handle Body onto the Mixer Cartridge Lever and ensure full engagement.

- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).

- Apply sealing tape (Teflon) to male thread.

- Place Dress Ring over outlet.

- Push Dress Ring back to meet the wall.

- Fit and align the Outlet.

- To complete installation , operate the Mixer(s) checking the flow of both hot and cold water from the Outlet .

Check all fittings and fixtures for water leaks.

sussextaps.com.au

Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003

Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c

View f rom ab ove

Masterﬁt

NOGGING

Dress Ring

Handle

Body

1/2" BSP

Male Outlet 1

30-32mm

Wall Covering

Max. 30mm

Mixer

Stud face

Min.

8mm

This

side

Outlet

Hot

Cold

Mixer

Outlet

Pipe Connections

Product code

Circa

RWBMS150RH Wall basin mixer system 150mm

RWBMS200RH Wall basin mixer system 200mm

RWBMS250RH Wall basin mixer system 250mm

RWBMS150RH-V Wall basin mixer system 150mm - Vertex

RWBMS200RH-V Wall basin mixer system 200mm - Vertex

RWBMS250RH-V Wall basin mixer system 250mm - Vertex

Wall basin mixer system Rough in

Plumbers note

Rough in plumbing

Pipe connections

- Prior to installing calculate the finished wall thickness, maximum is 30mm thick. Contact manufacturer for

further options.

- If Wall thickness is greater than 30mm, contact manufacturer for further options.

- Prepare a Nogging to be fixed parallel between the Wall Studs.

- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.

- The Masterfit will be marked “This side Up” to indicate orientation.

- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Master fit is level and square.

- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).

- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.

- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)

- Do not remove any factory fitted pressure plugs or Fixings.

- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.

- Check all fittings and fixtures for leaks.

- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.

- Store the Dress Kit in a safe place until required (see Dress Finishing Guide).

- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY )

- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.

- At the completion of the testing, do not relieve any high pressure by opening the Mixer.

- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the

manufacturer’s warranty.

sussextaps.com.au

Produkt Specifikationer

Mærke:	Sussex
Kategori:	Kran
Model:	RWBMS150RH

Har du brug for hjælp?

Hvis du har brug for hjælp til Sussex RWBMS150RH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kran Sussex Manualer

Sussex VSM-04 Manual

7 April 2025

Sussex CBM-54 Manual

7 April 2025

Sussex VSMQ-60 Manual

7 April 2025

Sussex VBM Manual

7 April 2025

Sussex RWBMS150RH Manual

7 April 2025

Sussex VSM-54 Manual

7 April 2025

Sussex VEBM120 Manual

31 August 2024

Sussex BWBMS210RH Manual

31 August 2024

Sussex RWBHS200RH Manual

31 August 2024

Sussex RBS Manual

31 August 2024

Kran Manualer

Nyeste Kran Manualer

Rohl Miscelo MI09D3GQMB Manual

7 April 2025

Oliveri KE2030 Manual

7 April 2025

Shaws AUSH-4341 Manual

7 April 2025

Shaws AUSH-4751 Manual

7 April 2025

Shaws AUSH-4756 Manual

7 April 2025

Shaws AUSH-4861 Manual

7 April 2025

Oliveri MT0039 Manual

7 April 2025

Shaws AUSH-4866 Manual

7 April 2025

Peerless-AV P299685LF Manual

5 April 2025

Rohl A3650LPWSSTN-2 Manual

3 April 2025