Sussex VWBMS160RH Manual

Sussex Vandhane VWBMS160RH

Læs gratis den danske manual til Sussex VWBMS160RH (2 sider) i kategorien Vandhane. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Sussex VWBMS160RH, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
5.0
litres per
minute
Licence No. 0124
In accordance with AS/NZS 6400
Sussex Taps Pty Ltd
WATER RATING
www.waterrating.gov.au
The more
stars the more
water efcient
NOGGING
80 mm
B/Plate
Apply Silicone
64mm
Dress
Ring
t
Apply Silicone
Stud Face
Finished
Wall Surface
Handle
Pin
Set
Screw
Handle
Body
2
NOGGING
t
Stud Face
Finished
Wall Surface
Backplate
Dress Ring
Bath Outlet
Product code
Voda
VWBMS160RH Wall basin mixer outlet system 160mm
VWBMS200RH Wall basin mixer outlet system 200mm
VWBMS250RH Wall basin mixer outlet system 250mm
Wall basin mixer outlet system Dress kit
2. Outlet fit off
1. Mixer dress kit
- Remove Mixer protective cover.
- Using silicone, seal the wall surface around the Mixer and Outlet threads.
- Apply a small amount of silicone to the rear of the backplate prior to mounting onto the wall.
- After Backplate has been mounted, fit the Mixer Dress Ring.
- Fit the handle body onto the Mixer Cartridge Lever ensuring the Handle is fully engaged.
- Secure the Handle Body by tightening the Set screw using the Allen Key provided (tighten well).
- Attach the Handle Pin.
Note: Apply a small amount of silicone or mild adhesive (Loctite) to the thread of the Handle Pin to assist in
preventing the Pin from becoming loose).
- Apply sealing tape (Teflon) to male thread.
- Place Dress Ring and Dress Flange over prepared male thread.
- Fitthe Outlet.
To complete the installation, operate the Mixer(s) checking the flow of both hot and cold water from Outlet.
Check all fittings and fixtures for water leaks.
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
1
View f rom above
NOGGING
Back Plate
Dress Ring
Handle
Body
1/2" BSP
Male Outlet 1
30-32mm
Wall Covering
Max. 30mm
90
70
Mixer
Stud face
Min.
8mm
This
side
UP
Outlet
Hot
Cold
Mixer
Outlet
Pipe Connections
Product code
Voda
VWBMS160RH Wall basin mixer outlet system 160mm
VWBMS200RH Wall basin mixer outlet system 200mm
VWBMS250RH Wall basin mixer outlet system 250mm
Wall basin mixer outlet system Rough-in
Plumber note
Pipe connections
Rough in plumbing
- Prior to installing, calculate the finished wall thickness, maximum is 30mm thick, contact manufacturer for
further options.
- If Wall thickness is greater than 30mm, contact manufacturer for further options.
- Prepare a Nogging to be fixed parallel between the Wall Studs.
- The Nogging must be fitted to enable the base of the Masterfit to be 30-32mm back from the Stud Face.
- The Masterfit will be marked “This side Up” to indicate orientation.
- Using the screws (x4) provided, mount the Masterfit to the Nogging. Ensure the Masterfit is level and square.
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY)
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specified water pressures, will void the
manufacturer’s warranty.
- The Hot and Cold ports are marked on the Masterfit. (Mixers have individual Hot/Cold inlet ports).
- Flush all water feed lines. All lines must be free from any dirt and debris before connecting to the Masterfit.
- Connect Hot and Cold lines to the corresponding 1/2” BSP ports of the Masterfit. (see Drawing)
- Do not remove any factory fitted pressure plugs or Fixings.
- Once all water connections are made, check Hot/Cold water flow by operating the Mixer Cartridge.
- Check all fittings and fixtures for leaks.
- Leave the Mixer(s) in the closed position and replace the Mixer protective cover.
- Store the Dress Kit in a safe place until required (see Dress Finishing Guide)
sussextaps.com.au
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.

Produkt Specifikationer

Mærke: Sussex
Kategori: Vandhane
Model: VWBMS160RH

Har du brug for hjælp?

Hvis du har brug for hjælp til Sussex VWBMS160RH stil et spørgsmål nedenfor, og andre brugere vil svare dig


Vandhane Sussex Manualer

Sussex

Sussex VSMC-14 Manual

8 Juli 2025
Sussex

Sussex VWBMS160RH Manual

5 Juli 2025
Sussex

Sussex VFM200TSXFMMIK Manual

5 Juli 2025
Sussex

Sussex VSMQ-04 Manual

5 Juli 2025
Sussex

Sussex RFMCTSXFMMIK Manual

5 Juli 2025
Sussex

Sussex BMDSRH Manual

25 September 2024
Sussex

Sussex BLMDSRH Manual

25 September 2024

Vandhane Manualer

Nyeste Vandhane Manualer

Krowne

Krowne Royal 16-182L Manual

29 September 2025
Stiebel Eltron

Stiebel Eltron MEWC Manual

28 September 2025
Stiebel Eltron

Stiebel Eltron MEK Manual

27 September 2025
Stiebel Eltron

Stiebel Eltron MEW Manual

27 September 2025
Gessi

Gessi 20577 Manual

27 September 2025
Stiebel Eltron

Stiebel Eltron EBK 5 GA Manual

27 September 2025
Gessi

Gessi 13193 Manual

27 September 2025
T&S

T&S EC-3105 Manual

23 September 2025
T&S

T&S B-0107-CM Manual

22 September 2025
Krowne

Krowne 12-812L Manual

17 September 2025