Synco G2A1 Manual

Synco Mikrofon G2A1

Læs gratis den danske manual til Synco G2A1 (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Synco G2A1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. Power On/ O󽗈

Power On

The TX and RX automatically turn on when long press the power button

for 3 seconds, and the display screen lights up.

Power O󽗈

The TX and RX automatically turn o󽗈 when long press the power button

for 3 seconds, and the display screen lights o󽗈.

2. Pairing

Automatic Pairing

Automatically pairing after the TX/RX turns on.

Manual Pairing

① Long press the transmitter and receiver at the same time for 3 seconds

to power o󽗈 .

② After shutdown, long press the power button of the transmitter and

receiver for 8 seconds at the same time to enter the [connecting ] state.

1. TX Transmitter

2. RX Receiver

① External Mic Input

② Type-C Charging Port

③ On/ O󽗈 Button

④ Built-in Mic

⑤ Display Screen

① Type-C Charging Port / Digital Output

② On/ O󽗈 Button (Mono / Stereo / Safety Channel)

③ 3.5mm TRS Output

④ 3.5mm Monitoring Port

⑤ Display Screen

⑥ Gain Adjustment of TX A

⑦ Gain Adjustment of TX B

⑧ Magnet Pocket Clip

Caring For Your SYNCO Product Product Instruction

Operations

Package List

· Please keep the product in a dry, clean, dust-free environment.

· Keep corrosive chemicals, liquids and heat source away from the

product to prevent mechanics damage.

· Use only a soft and dry cloth for cleaning the product.

· Malfunction may be caused by dropping, impact of external force.

· Do not attempt to disassemble the product. Doing so voids warranty.

· Please have the product checked or repaired by authorized technicians

if any malfunctions happened.

· Failure to follow all the instructions may result in mechanics damage.

· Warranty does not apply to human errors.

Microphone G2A1

User Manual

Thank you for choosing SYNCO product.

Please read this manual carefully before use and follow all instructions

mentioned herein.

⑥ Noise Reduction

⑦ Gain Adjustment of TX

⑧ Magnet Pocket Clip

3. Display Screen

Disconnected Connecting

Connected

③ Successfully Connected show as the picture

*Note: Before successful connection, the transmitter channel displays

A by default. The transmitter connected to the receiver 󽗉rst is the

transmitter A, and the later one is the transmitter B.

*Note: When using an external microphone, please insert it correctly

into the microphone input jack. Only TRS interface microphones are

supported.

3. Channel output connection

① 3.5mm OUT output

The receiver outputs the audio signal to the recording device via either a

3.5mm TRRS phone cable or a 3.5mm TRS camera cable. Please use the

appropriate cable according to your device.

Apple Adapter (With MFI Certi󽗉cation)

3.5mm TRRS Phone Cable

3.5mm TRS Camera Cable

② Type-C port digital output

The receiver Type-C port has a digital output function, which can directly

use the Type-C to Type-C cable to output mobile phones or computers

and other devices.

4. Real-time monitoring

The 3.5mm monitoring port of the receiver supports digital monitoring,

which can simultaneously monitor the sound source of the transmitter

and the input sound source of the device.

5. Volume Control

① Press the power button on the TX to turn on/o󽗈 the mute.

② Short press the gain adjustment button of the TX to adjust the volume

for 6 levels (0-3-6-9-12-15).

③ Short press the gain adjustment of A/B TX buttons on the RX to adjust

the volume of A/B TX.

3.5mm Monitoring Jack

Headphone Impedance: under 100 Ω

*Note: When connecting the computer, enter the sound Settings and

set the input microphone to SYNCO G2Pro to use G2 recording; Set the

output speaker to SYNCO G2 Pro to use real-time ear return in the receiver

listening interface.

Recording

TX A

Gain of A TX

Audio Dynamic

Display of A TX

Noise Reduction on

TX Transmitter

RX Receiver

Muting

Recording Mode:

Mono/ Stereo/ Safety

Disconnected

Connecting

Connected

Audio Dynamic

Display

Power Indicator

TX B

Gain of B TX

Audio Dynamic

Display of TX B

Power Indicator

RX Receiver x1 TX Transmitter

2-in-1 Charging Cable x1 External Lav Mic (With Wind Mu󽗈) x1

3.5mm TRRS Phone Cable x1 3.5mm TRS Camera Cable x1

Mic Windshield x1 Magnet x1 User Manual X1

Carrying Bag x1

Wireless Transmission

RF Frequency Band

Working Distance

Mounting

Audio Input

Power Requirements

Battery Type

Battery Charging Time

Battery Life

Display Screen

Dimensions

Material

Weight

Wireless Transmission

RF Frequency Band

Working Distance

Latency

Mounting

Number of Audio Channels

Audio Output

Volume Adjustment

Power Requirements

Battery Type

Battery Charging Time

Battery Life

Display Screen

Dimensions

Material

Weight

Form Factor

Frequency Range

Sensitivity

Maximum SPL

Digital 2.4GHz

2400-2483.5MHz

656ft/200m (LOS area), 164ft/50m (NLOS area)

Pocket Clip

3.5 mm TRS Mic Input

5V 1A

Built-in Lithium Battery, 400mAh

TFT Screen

52X42X17mm

ABS

39g

Digital 2.4GHz

2400-2483.5MHz

656ft/200m (LOS area)

164ft/50m (NLOS area)

20ms

Pocket Clip

3.5 mm TRS Mic Output

3.5 mm TRS Headphone Output

Type-C Output

6 levels (0-3-6-9-12-15)/(0~30dB)

5V 1A

Built-in Lithium Battery, 400mAh

TFT Screen

52X42X17mm

ABS

39g

Built-in/External Mic

50Hz-20KHz

-35dB（±3dB，re 1V/Pa at 1 KHz）

120dB SPL（at 1KHz）

TX Transmitter

RX Receiver

Microphone

7.Switch the Channel Mode

Short press the power button on the RX to switch the mono/stereo/safety

channel mode.

Default mono mode.

8.Charging

Connect the charging cable through Type-C port of TX and RX，and fully

charged in about 2 hours.

( The grey end of the 2-in-1 charging cable included in the packageNote:

can be used for digital output. )

9. Mic Windshield & Device Installation

Screw to mount the windshield.

10.Setting The Recording Level Correctly

TX RX

Camera devices generally have poor-quality, noisy preamps. In order to

get the cleanest signals possible, it is highly recommended that you set

the recording level on your camera quite low, 1/2 or 1/3 of it.

G2 provides variable gain control, allowing you to tailor your levels to just

about environment and recording device.

Adjust the recording level of inbuilt mics for SONY Camera

(Take A7S Ⅱ for example)

Adjust the recording level of inbuilt mics for Canon Camera

(Take EOS 5D Mark Ⅳ for example)

Adjust the recording level of inbuilt mics for Panasonic Camera

(Take LUMIX GH5 for example)

Speci󽗉cations

*Please register your warranty. Meanwhile, you are welcomed to contact us via Email：

support@syncoaudio.com

Guangzhou Zhiying Technology Co., Ltd

Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District,

Guangzhou, China, 510000

support@syncoaudio.com

www.syncoaudio.cn

Warranty Period

Warranty Exclusions and Limitations

Warranty Claim Procedure

Thank you for purchasing SYNCO products.

1. Customers are entitled to free replacement or repair service in case of

quality defect(s) found in the product under normal use within 30 days

upon receipt of the product.

2. Original SYNCO products are entitled to 12-month limited warranty

service. The warranty period begins on the date of purchase of brand new,

unused products by the 󽗉rst end-user.

Within the warranty period, if product defect or failure is attributable to

material defection or technological problem, the defective product or

defective part will be repaired or replaced without charge (service and

materials fee).

Faults resulted from inappropriate use of a product without following its

operation speci󽗉cation：

1. Arti󽗉cial damage, e.g. crash, squeeze, scratch, or soaking

2. Modi󽗉cations to a product by its user or a third party without prior

written consent of SYNCO, e.g. replacement of element or circuit, label

alteration

3. The code on product is inconsistent with that of warranty certi󽗉cate, or

the code on the product or warranty certi󽗉cate is altered or torn o󽗈

4. All consumable accessory attached to a product, like cable, wind mu󽗈,

battery

5. Faults as a result of force majeure, such as 󽗉re, 󽗊ood, lightning, etc.

1. If failure or any problem occurs to your product after purchase, please

contact a local agent for assistance, or you can always contact SYNCO’s

customer service through email at support@syncoaudio.com.

2. Please retain your sales receipt and warranty certi󽗉cate as proof of

purchase. If any of these documents is missing, only sales return or

chargeable service will be provided.

3. If the SYNCO product is out of the warranty coverage, the service and

the parts cost will be charged.

Warranty

Product Model:

Date of Purchase:

Serial Number:

Malfunction Description :

Buyer Name:

Buyer Telephone :

Buyer Mail :

Buyer Address :

Dealer :

Dealer Telephone :

Delivery Date :

Cause of Malfunction :

Maintenance Personnel :

Malfunction Processing :

WARRANTY CERTIFICATE

6. Noise Cancellation

Short press the noise cancellation button on the transmitter to switch

between noise-control modes:

① Noise Cancellation O󽗈

② Low-Level Noise Cancellation

③ High-Level Noise Cancellation

Noise Cancellation O󽗈High-Level Noise

Cancellation

Low-Level Noise

Cancellation

Produkt Specifikationer

Mærke:	Synco
Kategori:	Mikrofon
Model:	G2A1

Har du brug for hjælp?

Hvis du har brug for hjælp til Synco G2A1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Synco Manualer

Synco WAir P2S Manual

11 September 2025

8 Juli 2025

5 Juli 2025

23 Juni 2025

2 April 2025

2 April 2025

Synco MC3 LITE Manual

2 April 2025

Synco G2A2 Manual

2 April 2025

Synco G1A1 Manual

2 April 2025

Synco G1 Pro Manual

2 April 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

Adam Hall 5730 Manual

11 September 2025

Point Source Audio Series8 CR-8S Manual

10 September 2025

Musicmate B-13 Manual

10 September 2025

Defender Space GMC 450 Manual

10 September 2025

Musicmate S-105N ClearTone Manual

10 September 2025

I.safe Mobile IS-RSM3A.1 Manual

10 September 2025

Krux Esper 1000 Manual

10 September 2025

Krux Epic 1000 Manual

9 September 2025

Røde SC7 Manual

9 September 2025

Cellular Line Talk Pro Manual

9 September 2025