System Sensor F-A3384-000 Manual

System Sensor Ikke kategoriseret F-A3384-000

Læs gratis den danske manual til System Sensor F-A3384-000 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om System Sensor F-A3384-000, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

F-A3384-000 Air Filter Assembly

INSTALLATION AND MAINTENANCE INSTRUCTIONS

GENERAL DESCRIPTION

The F-A3384-000 replacement air filter for the FAAST™ 8100 series aspiration

detectors comes fully assembled and ready to use. It is a 30 micron filter de-

signed specifically for use with the FAAST system.

FILTER ASSEMBLY REPLACEMENT

The filter is located behind the Display Door under the User Interface Card, as

shown in Figure 1.

FIGURE 1. FRONT VIEW OF DETECTOR WITH DISPLAY DOOR OPEN AND

USER INTERFACE CARD IN PLACE:

USER INTERFACE CARD

ASP-82

To replace the filter perform the procedure in Table 1.

TABLE 1. FILTER REPLACEMENT PROCEDURE

STEP ACTION

1 Before performing maintenance, notify the proper authorities that the

system is undergoing maintenance, and will temporarily be out of ser-

vice. Disable the system to prevent unwanted alarms.

2 Turn off the system by removing the 24 Volt power connector from the unit

or by unplugging the converter from its power outlet.

NOTE: If power is not removed, the unit automatically enters Service

Mode when the screws are removed from the filter. This removes

power from the fan and the sensing chamber. In addition, the filter

fault indicator is illuminated and the urgent relay is set.

3 Open the Display Door, as shown in Figure 1, and remove the User

Interface card in front of the filter.

4 Remove the two Philips head screws securing the filter to the unit,

as shown in Figure 2.

5 Replace the entire filter assembly, as shown in Figure 3, with a new

unit by pulling the old filter out and sliding a new filter assembly

back into position.

6 Torque the two Philips head screws to 6in-lb (0.7N-m) or ¼ turn

past “lightly snug”. DO NOT OVER TIGHTEN.

7 Carefully reinstall the User Interface card.

1 I56-3743-003

3825 Ohio Avenue, St. Charles, Illinois 60174

1.800.SENSOR2; Fax: 630.377.6495

www.systemsensor.com

I56-3743-003

FILTER MOUNTING SCREWS

(DO NOT OVERTIGHTEN)

ASP90-01

FIGURE 3. REMOVABLE AIR FILTER ASSEMBLY:

FILTER MOUNTING SCREWS

(DO NOT OVERTIGHTEN)

ASP91-01

FIGURE 2. FILTER MOUNTING SCREWS WITH USER INTERFACE

CARD REMOVED:

Produkt Specifikationer

Mærke:	System Sensor
Kategori:	Ikke kategoriseret
Model:	F-A3384-000

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor F-A3384-000 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret System Sensor Manualer

System Sensor PC2RL Manual

25 August 2024

System Sensor PC2WL Manual

25 August 2024

System Sensor PC2W Manual

25 August 2024

System Sensor HRK Manual

14 August 2024

System Sensor MP120KL Manual

13 August 2024

System Sensor P2R-SP Manual

9 August 2024

System Sensor F-A3384-000 Manual

9 August 2024

System Sensor SMB500 Manual

8 August 2024

System Sensor P2RL-SP Manual

7 August 2024

System Sensor P2RL Manual

7 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

EVE Thermo (4th generation) Manual

8 Januar 2026

Ikea LEN 704.576.37 Manual

8 Januar 2026

Happimess DSH1002A Manual

8 Januar 2026

Perrin & Rowe U.3720L Manual

8 Januar 2026

Ikea HAMMARSMED 605.903.78 Manual

8 Januar 2026

Ikea LERHYTTAN 105.949.77 Manual

8 Januar 2026

Canarm KE-11S Manual

8 Januar 2026

Ikea BJÖRKSTA 505.789.18 Manual

8 Januar 2026

Canarm PW-14SX Manual

8 Januar 2026

EGO APB2000 Manual

8 Januar 2026