System Sensor P2RL-SP Manual

System Sensor Ikke kategoriseret P2RL-SP

Læs gratis den danske manual til System Sensor P2RL-SP (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om System Sensor P2RL-SP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 I56-5845-001

01-12

BEFORE INSTALLING

Please read the System Sensor Audible Visible Application Reference Guide,

which provides detailed information on notification devices, wiring and spe-

cial applications. Copies of this manual are available from System Sensor.

NFPA 72 and NEMA guidelines should be observed.

Important: The notification appliance used must be tested and maintained

following NFPA 72 requirements.

GENERAL DESCRIPTION

System Sensor series of notification appliances offer a wide range of audible

and visible devices for life safety notification. Our 2-wire horn strobes, chime

strobes and strobes come with 8 field selectable tone and volume combina-

tions and 7 field selectable candela settings. Intended for indoor applications

and approved for wall mount installations only. Available in two attractive

mounting designs, standard and compact (horn strobe and strobe only).

2-wire horn strobes and strobes are public mode notification appliances in-

tended to alert occupants of a life safety event. The 2-wire chime strobe is

a private mode notification appliance. The horn is listed to ANSI/UL 464

requirements (public mode) and the strobe is listed to ANSI/UL 1638 (pub-

lic mode). 2-wire chime strobe is a private mode notification appliances in-

tended to alert trained personnel to investigate a life safety event and take

appropriate actions. The chime portion of the chime strobe is listed to ANSI/

UL 464 (private mode) and the strobe portion is listed to ANSI/UL 1638 (pri-

vate mode).

System Sensor notification appliances are designed to be used in either 12

VDC, 24VDC, or 24V FWR (full wave rectified) systems. System Sensor AV de-

vices can be activated by a compatible fire alarm control panel or power sup-

ply. Refer to the appropriate fire alarm control panel manufacturer or power

supply for more information.

System Sensor wall 2-wire horn strobes, 2-wire chime strobes, and strobes are

electrically backward compatible with the previous generation, since 1996,

of notification appliances. They come enabled with System Sensor synchro-

nization protocol which requires connections to a power supply capable of

generating the System Sensor synchronization pulses, a FACP NAC output

configured to System Sensor synchronization protocol, or the use of MDL3

module to generate the synchronization protocol.

FIRE ALARM SYSTEM CONSIDERATIONS

The National Fire Alarm and Signaling Code, NFPA 72, requires that all noti-

fication appliances, used for building evacuation installed after July 1, 1996,

produce temporal coded signals. Signals other than those used for evacuation

purposes do not have to produce the temporal coded signal. System Sensor

recommends spacing notification appliances in compliance with NFPA 72.

SYSTEM DESIGN

The system designer must make sure that the total current draw by the devices

on the loop does not exceed the current capability of the panel supply, and

that the last device on the circuit is operated within its rated voltage. The

current draw information for making these calculations can be found in the

tables within the manual. For convenience and accuracy, use the voltage drop

calculator on the System Sensor website (www.systemsensor.com).

When calculating the voltage available to the last device, it is necessary to

consider the voltage due to the resistance of the wire. The thicker the wire, the

smaller the voltage drop. Wire resistance tables can be obtained from electri-

cal handbooks. Note that if Class A wiring is installed, the wire length may

be up to twice as long as it would be for circuits that are not fault tolerant.

The total number of strobes on a single NAC must not exceed 69 for 24 volt

applications.

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Selectable Output

Horn Strobes, Chime Strobes

and Strobes – Wall Mount

For use with the following models:

Standard Wall Mount Horn Strobes: P2RL, P2WL, P2RL-P, P2WL-P, P2RL-SP, P2WL-SP

Compact Wall Mount Horn Strobes: P2GRL, P2GWL

Standard Wall Mount Chime Strobes: CHSRL, CHSWL

Standard Wall Mount Strobes: SRL, SWL, SRL-P, SWL-P, SRL-SP, SWL-CLR-ALERT

Compact Wall Mount Strobes: SGRL, SGWL

PRODUCT SPECIFICATIONS

Standard Operating Temperature: 32°F to 120°F (0°C to 49°C)

Humidity Range: 10 to 93% Non-condensing

Strobe Flash Rate 1 flash per second

Nominal Voltage: Regulated 12VDC or regulated 24DC/FWR

Operating Voltage Range: 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal)

Operating Voltage with MDL3 Sync Module: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal)

Input terminal wire gauge: 12 to 18 AWG

DIMENSIONS FOR PRODUCTS AND ACCESSORIES

WALL PRODUCTS Length Width Depth

Standard Strobe, Chime Strobe and Horn Strobe

5.6" (143mm) 4.7" (119mm) 1.25" (32mm)

Compact Strobe and Horn Strobe

5.26" (133 mm) 3.46" (88 mm) 1.93 (49 mm)

Standard device with SBBRL/WL Surface Mount Back Box 5.9" (149 mm) 4.9" (125 mm) 1.85" (47 mm)

ompact device with

SBBGRL/WL Surface Mount Back Box

5.5" (140 mm) 3.7" (94 mm) 1.6" (39 mm)

NOTE: SBBRL/WL Surface Mount Back Box intended only for standard horn strobes, chime strobes and strobes.

SBBGRL/WL Surface Mount Back Box intended for compact horn strobes and strobes.

MOUNTING BOX OPTIONS

Standard 2-Wire Indoor Products: 4" x 4" x 1½", Single Gang, Double Gang, 4" Octagon, SBBRL/WL (wall), SBBGRL/WL (wall)

Compact 2-Wire Indoor Products: Single Gang, SBBGRL/WL (wall)

NOTICE: This manual shall be left with the owner/user of this equipment.

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

I56-5845-001

Produkt Specifikationer

Mærke:	System Sensor
Kategori:	Ikke kategoriseret
Model:	P2RL-SP

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor P2RL-SP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret System Sensor Manualer

System Sensor PC2RL Manual

25 August 2024

System Sensor PC2WL Manual

25 August 2024

System Sensor PC2W Manual

25 August 2024

System Sensor HRK Manual

14 August 2024

System Sensor MP120KL Manual

13 August 2024

System Sensor P2R-SP Manual

9 August 2024

System Sensor F-A3384-000 Manual

9 August 2024

System Sensor SMB500 Manual

8 August 2024

System Sensor P2RL-SP Manual

7 August 2024

System Sensor P2RL Manual

7 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

EVE Thermo (4th generation) Manual

8 Januar 2026

Ikea LEN 704.576.37 Manual

8 Januar 2026

Happimess DSH1002A Manual

8 Januar 2026

Perrin & Rowe U.3720L Manual

8 Januar 2026

Ikea HAMMARSMED 605.903.78 Manual

8 Januar 2026

Ikea LERHYTTAN 105.949.77 Manual

8 Januar 2026

Canarm KE-11S Manual

8 Januar 2026

Ikea BJÖRKSTA 505.789.18 Manual

8 Januar 2026

Canarm PW-14SX Manual

8 Januar 2026

EGO APB2000 Manual

8 Januar 2026