System Sensor P2R-SP Manual

System Sensor Ikke kategoriseret P2R-SP

Læs gratis den danske manual til System Sensor P2R-SP (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 100 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 50.5 anmeldelser. Har du et spørgsmål om System Sensor P2R-SP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 I56-2769-020R

06-10

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Selectable Output Strobes, Horns, and Horn/Strobes

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

For use with the following models: P2R, P2RH, P2RK, P2RHK, P2W, P2WK, P2WH, P2WHK, P4R, P4RH, P4RK, P4W, P4WK, SR, SRH, SRK, SRHK, SW, SWK, SWH, SWHK, SW-CLR-

ALERT, PC2R, PC2RH,PC2RK, PC2RHK, PC2W, PC2WK, PC2WH, PC2WHK, PC4R, PC4RH, PC4W, PC4WK, PC4WHK, SCR, SCRH, SCRK, SCRHK, SCW, SCWK, SCWH, SCWHK, SCW-

CLR-ALERT, HR, HRK, HW, SR-P, SW-P, SRH-P, SWH-P,P2R-P, P2W-P, P2WH-P, P4R-P, P4W-P, SCW-P, PC2R-P, PC2W-P, PC2WH-P, SRK-P, SRHK-P, P2RK-P, P2RHK-P, SWK-P, SWHK-P,

P2WK-P, P2WHK-P, SR-SP, P2R-SP, PC2W-SP, SRK-R, SWK-R, SRHK-R, SWHK-R, P2RK-R, P2WK-R, P2RHK-R, P2WHK-R, SBHK, SBK-R

NOTE: All -R models are specifically designed for use with the WTP Series of Weatherproof plates

NOTE: When replacing outdoor units; device and back box must be replaced

NOTE: Models SBHK, SBK-R are UL listed for General Signaling

PRODUCT SPECIFICATIONS

Operating Temperature: Standard Products 32°F to 120°F (0°C to 49°C)

K Series –40°F to 151°F

Humidity Range: Standard Products 10 to 93% Non-condensing

K Series Meets NEMA 4X requirements

Strobe Flash Rate: 1 ﬂash per second

Nominal Voltage: Regulated 12VDC/FWR or regulated 24DC/FWR

Operating Voltage Range (includes ﬁre alarm panels with built in sync): 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal)

Operating Voltage with MDL3 Sync Module: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal)

Input terminal wire gauge: 12 to 18 AWG

NOTE : Strobes will operate at 12 V nominal for 15 & 15/75 candela settings only. Switching between ranges is automatic.

DIMENSIONS FOR PRODUCTS AND ACCESSORIES

WALL PRODUCTS Length Width Depth CEILING PRODUCTS DIAMETER DEPTH

Strobe and Horn/Strobes (including lens)

5.6" 4.7" 2.5" Strobes and Horn/Strobes

(including lens)

6.8" 2.5"

142 mm 119 mm 64 mm 173 mm 64 mm

Horns

5.6" 4.7" 1.3"

SA-WBBC Red Weatherproof Back Box

7.1" 2.2"

142 mm 119 mm 33 mm

SA-WBBCW White Weatherproof Back Box

180 mm 51 mm

SA-WBB Red Weatherproof Back Box

5.7" 5.1" 2.0"

SBBCR Red Surface Mount Box

6.9" 5.3"

SA-WBBW White Weatherproof Back Box

145 mm 130 mm 51 mm

SBBCW White Surface Mount Box

175 mm 135 mm

SBBR Red Surface Mount Box

5.6" 4.7" 4.3" NOTE: SA-WBB, SA-WBBW, SA-WBBC and SA-WBBCW dimensions

do not include the two mounting tabs

SBBW White Surface Mount Box

142 mm 119 mm 109 mm

MOUNTING BOX OPTIONS

2-Wire Indoor Products 4-Wire Indoor Products K Series Products

4 × 4 × 1

1/2, Single Gang, Double Gang, 4˝ Octagon

SBBR/W (wall), SBBCR/W (ceiling) 4 × 4 × 11/ ,2 Double Gang, 4˝ Octagon SA-WBB/W (wall), SA-WBBC/CW (ceiling)

GENERAL DESCRIPTION

The SpectrAlert Advance series of notification appliances offers a wide range

of horns, strobes, and horn/strobes, for wall and ceiling applications, indoors

and outdoors. They are designed to be used on 12 or 24 volt, DC or FWR

(full wave rectified) systems. These products are electrically backward compat-

ible with the previous generation of SpectrAlert notification appliances. Horn/

strobe products are available in two versions. The 2-wire products fit systems

where a single NAC controls both horn and strobe. The 4-wire products are in-

tended for systems which have separate wiring circuits for the horn and strobe.

All SpectrAlert Advance products are suitable for use in synchronized systems.

The System Sensor MDL3 module may be used to provide synchronization.

K Series products are designed to be used over a wider range of temperatures

and are suitable for use in wet environments with outdoor backbox supplied

with product.

Wall and ceiling products may be used interchangeably (wall products

may be used on the ceiling and ceiling products may be used on the wall.)

FIRE ALARM SYSTEM CONSIDERATIONS

The National Fire Alarm Code, NFPA 72, requires that all horns, used for

building evacuation produce temporal coded signals. Signals other than those

used for evacuation purposes do not have to produce the temporal coded sig-

nal. System Sensor recommends spacing notification appliances in compli-

ance with NFPA 72.

LOOP DESIGN AND WIRING

The system designer must make sure that the total current drawn by the de-

vices on the loop does not exceed the current capability of the panel supply,

and that the last device on the circuit is operated within its rated voltage. The

current draw information for making these calculations can be found in the

tables within this manual. For convenience and accuracy, use the voltage drop

calculator on the System Sensor website (www.systemsensor.com).

When calculating the voltage available to the last device, it is necessary to

consider the voltage drop due to the resistance of the wire. The thicker the

wire, the smaller the voltage drop. Wire resistance tables can be obtained

from electrical handbooks. Note that if Class A wiring is installed, the wire

length may be up to twice as long as it would be for circuits that are not

fault tolerant.

NOTE: The total number of strobes on a single NAC must not exceed 40 for

24 volt applications or 12 for 12 volt applications. Loop resistance on a single

NAC should not exceed 120 ohms for 24 volt and 30 ohms for 12 volt systems.

I56-2769-020R

NOTICE: This manual shall be left with the owner/user of this equipment.

Produkt Specifikationer

Mærke:	System Sensor
Kategori:	Ikke kategoriseret
Model:	P2R-SP

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor P2R-SP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret System Sensor Manualer

System Sensor PC2RL Manual

25 August 2024

System Sensor PC2WL Manual

25 August 2024

System Sensor PC2W Manual

25 August 2024

System Sensor HRK Manual

14 August 2024

System Sensor MP120KL Manual

13 August 2024

System Sensor P2R-SP Manual

9 August 2024

System Sensor F-A3384-000 Manual

9 August 2024

System Sensor SMB500 Manual

8 August 2024

System Sensor P2RL-SP Manual

7 August 2024

System Sensor P2RL Manual

7 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Maax 410002 Manual

7 Januar 2026

Canarm 809 Manual

7 Januar 2026

RectorSeal AG-1250E Manual

7 Januar 2026

Vaxcel T0263 Manual

7 Januar 2026

WAC Lighting J-LED009 Manual

7 Januar 2026

Blaupunkt BP-PA2800 Manual

7 Januar 2026

Reelcraft CEA30006 Manual

7 Januar 2026

WAC Lighting JHT-808 Manual

7 Januar 2026

Canarm MCY24T10075C Manual

7 Januar 2026

Canarm 936 Manual

7 Januar 2026