TacTic AnyLink2 Manual

TacTic Radiostyret legetøj AnyLink2

Læs gratis den danske manual til TacTic AnyLink2 (9 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4 anmeldelser. Har du et spørgsmål om TacTic AnyLink2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

The AnyLink2 SLT 2.4GHz

Radio Adapter can greatly

expand a transmitter’s

versatility, allowing it to be

used with a huge variety

of ﬂ ight models, including

Tx-R

™

Transmitter-Ready

™

aircraft (including Select Scale and Micro Tx-R models). AnyLink2 is

capable of full range, to control any size aircraft.

Read this manual in its entirety before use! Damage resulting

from misuse or modiﬁ cation will void your warranty.

ITEMS INCLUDED

(1) AnyLink2 2.4GHz Radio Adapter with 1S LiPo Battery

(1) Cable A – JR®, Spektrum®, Graupner®

(1) Cable B – Futaba® Square

(1) Cable C – Spektrum, Hitec®

(1) TC10 USB Charger

(2) Hard Locking Adhesive Strips

(1) Instruction sheet

COMPATIBLE TRANSMITTERS

AND RECEIVERS

AnyLink2 can link virtually any brand transmitter (Tx) to any Tactic brand

2.4GHz receiver (Rx) such as the TR624 or TR625. Transmitters must be

equipped with a functioning trainer jack, and can originally be designed

for use on 72MHz, 2.4GHz, FM, PCM, etc. Go to www.tacticrc.com for a

comprehensive Tx compatibility chart. AnyLink2 is not compatible with

non-Tactic brand receivers not having SLT technology.

TX CABLE

See the chart below to determine the cable needed to connect AnyLink2 to

the Tx. Three cables are included, for many Futaba, Hitec, JR, Spektrum,

and Graupner brand radios.

This chart is current as of the date of the printing of this manual. Check

www.tacticrc.com for the most updated compatibility chart. Transmitters

not listed may or may not be compatible with AnyLink2. See your local

hobby retailer for optional cables for other radio types:

TACM0013 AnyLink2 Cable Futaba/Hitec Round

TACM0014 AnyLink2 Cable Airtronics SD-Series

TACM0015 AnyLink2 Cable Airtronics 5-Pin Round

IMPORTANT: For some transmitters, connecting a cable to the

trainer jack will automatically cause the Tx logic circuitry to turn

on. When not in use, make sure to disconnect the cable from trainer jack

to prevent the Tx battery from discharging completely.

ANYLINK2

AnyLink2 Transmitter Compatibility Chart

ANYLINK2

MODE

BRAND MODEL CABLE

Futaba®

4YF (72M, 2.4G), 4YBF, 6EX, TJ, 7C, 8FG, 8J, 9C, 10C, 14SG; (12FG, 12Z, 14MZ, 18MZ

> )See note page 2 *

4VF, 5U, 6A, 6DA, 6H, 6X, 6YF, 6YG, 7U, 7NFK, 8U, 9Z

Hitec ®

Optic 5, Optic 6 Sport, and Eclipse 7 (all on 2.4GHz), Aurora 9

Neon, Flash 4sx, Flash 5, Flash 5sx, Focus 4, Focus 6, Laser 4, Laser 6, Optic 5 (72M),

Optic 6 (72M, 2.4G), Eclipse 7 (72M), Prism 7, Prism 7X

Tower Hobbies

4FM, 6FM

4TH, 6XM

Graupner ®

MX-12, MX-16

Walkera ®

Devo 7, Devo 8S

Airtronics ®

SD-5G, SD-6G, SD-10G

Vanguard 4FM, 6FM, RD6000 Sport, RD6000 Super, RDS8000, Radiant 6FM

Spektrum

DX4e, DX5e, DX6, DX7, DX7s, DX8, DX9, DX10T, DX18

DX6i

JR ®

All with trainer/DSC jack

(Included)

(TACM0013)

(TACM0014)

(TACM0015)

BATTERY AND CHARGER

AnyLink2 is powered by an included 1S 3.7V 450mAh lithium-polymer

battery (LiPo).

IMPORTANT:

It will be necessary to fully charge the battery with

the included USB charger before use! Follow all safety precautions

below before proceeding. Failure to do so may cause AnyLink2 to lose

power prematurely, resulting in a loss of control signal and causing the

model to crash.

●

NEVER LEAVE BATTERY UNATTENDED WHILE CHARGING

● Never allow the battery temperature to exceed 140°F (60°F)

● Never place battery on combustible materials while charging

● Never attempt to disassemble or modify the battery

● Never attempt to charge or continue to use the battery if it’s swollen,

punctured, or deformed in any way.

● Never attempt to charge the battery with an incompatible battery

charger. Only use the included charger.

● Follow appropriate disposal instructions when the battery has reached

the end of its useful life

Open the battery door on the rear side of AnyLink2 and remove the battery.

2. Connect the included TC10 USB charger to a personal computer’s USB

port, and turn the computer on.

3. Connect the LiPo battery to the jack on the opposite end of the charger.

4. The charger’s red LED will turn on to conﬁ rm charge is being delivered.

When the charger automatically detects full charge is achieved, the red

LED will ﬂ ash slowly. The battery can be removed at this time and is ready

for use. Note: Rapid ﬂ ashing of the LED indicates an error occurred.

The battery should be disconnected from the charger and placed in a

ﬁ reproof location. Contact Hobby Services

6. If the battery was successfully charged, attach it to the connector inside

AnyLink2. Carefully insert the battery inside AnyLink2 and close the

door, making sure not to pinch the wires in the door.

AnyLink2 turns on automatically when connected to a host transmitter

and a signal is present at the trainer jack. Otherwise, AnyLink2’s power

will remain off.

Tones will sound from AnyLink2 if its battery voltage drops to an unsafe

level (3.25V). Land the aircraft immediately to avoid loss of control

and possible destruction of the model. Fully re-charge the battery before

further use.

ANYLINK2 MODE SETUP

IMPORTANT!

Remove the airplane’s propeller prior to setting up

AnyLink2 to work with the ﬂ ight system. Failure to do so could result

in personal injury if the motor turns unexpectedly. Make sure all

batteries are fully charged prior to operation. Make sure all connections are

solid physically and cannot easily become dislodged at any time. AnyLink2

must be used with a Tx having a throttle stick that does NOT automatically

spring back to center.

1. Create a new model memory in the host transmitter before starting to

conﬁ gure AnyLink2.

2. Mount AnyLink2 to the host Tx, by either clipping the mounting grip

onto the handle of the host Tx, or using the two hard locking mounting

strips included. Extend AnyLink2’s antenna upwards from the top of the

Tx as much as possible.

3. Remove the Rf module or crystal from the host Tx if possible, or disable

its Rf function.

4. Leave the transmitter’s own antenna in a retracted or folded position.

For computer radios make sure the modulation is set to PPM mode. For

transmitters having the option to transmit a signal when Tx power is

turned ON, make sure “YES” is selected. Futaba 12FG, 12Z, 14MZ, and *

18MZ transmitters must be mapped for Futaba channel order before use.

6. Move the throttle stick to minimum; leave all other sticks at center.

Connect the appropriate cable to the Tx trainer jack. If the transmitter’s

logic turns on automatically do NOT turn the Tx’s power switch on as it

could cause AnyLink2 to not function. Otherwise, if the transmitter’s logic

circuitry does NOT turn on automatically, turn the Tx power switch ON.

8. AnyLink2 should beep when a signal is received from the Tx and a red

LED should illuminate at this time. Identify the letter printed next to the

illuminated LED from the following list:

F Futaba

J JR (also works for Graupner)

S Spektrum

H Hitec

A Airtronics (also works for Walkera)

C Custom

If the LED illuminates next to the proper letter for the connected radio,

skip to the next section.

If the proper LED is not illuminated, insert a small screwdriver into the hole

next to “MODE” and press the button repeatedly until the LED illuminates

next to the proper Tx brand letter. The LED will ﬂ ash. Disconnect the cable

from AnyLink2, and re-connect. The LED should now stay on constantly

next to this selected radio setting. AnyLink2 should now be conﬁ gured for

the Tx and will retain this setting even after power is removed. Resetting

AnyLink2’s radio setting will only be necessary when a different brand Tx

will be connected.

CUSTOM MODE SETUP

If using a radio brand not listed above, AnyLink2 can be custom conﬁ gured

for your radio.

1. Create a new model memory in the host transmitter before starting to

conﬁ gure AnyLink2.

2. Move the Tx throttle stick and throttle trim to minimum position. Leave

all other sticks and trims at center position.

3. Connect the proper cable to the host transmitter’s trainer jack. If the

transmitter’s logic doesn’t turn on automatically, turn the Tx power

switch ON.

4. Connect the cable to AnyLink2, which should power up automatically if

a trainer signal is present.

5. Press AnyLink2’s MODE button and hold until the LED next to “C”

begins to ﬂ ash.

6. Move the throttle trim to center position, then move the throttle stick

to center position. A tone should sound to indicate the throttle channel

is at center.

7. Determine which stick will be used for aileron control. Move that stick to

the far-right position, then to the far-left position, then return to center.

8. Determine which stick will be used for elevator control. Move that stick

to the far-up position, then to the far-down position, then return to

center.

9. Determine which stick will be used for throttle control. Move that stick

to the far-up position, then far-down position, then return to center.

10 . Determine which stick will be used for rudder control. Move that stick

to the far-right position, then far-left position, then return to center.

11 .

Move the throttle stick to minimum position, which should be followed by

a beep and the LED should illuminate next to “C” to indicate Custom mode

is set. AnyLink2 will save this custom data and exit this setting mode.

12 . Remove power from AnyLink2, and then re-apply. AnyLink2 should be

conﬁ gured to work with this Tx. Once power is removed from AnyLink2

it will not be necessary to reset Custom mode.

LINKING TO A TACTIC RX

Produkt Specifikationer

Mærke:	TacTic
Kategori:	Radiostyret legetøj
Model:	AnyLink2

Har du brug for hjælp?

Hvis du har brug for hjælp til TacTic AnyLink2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj TacTic Manualer

TacTic TR325 Manual

12 September 2024

TacTic AnyLink2 Manual

1 September 2024

TacTic TACJ2005 Manual

27 Juli 2024

TacTic TTX410 Manual

6 Juli 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

Revell Glowee 2.0 Beast Manual

27 September 2025

Revell Quatcopter Nano Pocket Manual

27 September 2025

Blade 230 S Smart Manual

23 September 2025

Losi Mini LMT Manual

15 September 2025

Graupner WP Pilatus Porter Manual

14 September 2025

Losi Micro SCTE Manual

14 September 2025

Graupner mc-32 Manual

14 September 2025

Losi 1/18 Mini Desert Buggy RTR Manual

14 September 2025

Losi Mini-B Manual

14 September 2025

Graupner 8474 Manual

14 September 2025