Tascam DA-60MKII Manual

Tascam Lydoptager DA-60MKII

Læs gratis den danske manual til Tascam DA-60MKII (8 sider) i kategorien Lydoptager. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Tascam DA-60MKII, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

DA-60 IIMK

QUICK TIPS

Note: Whenever this document directs you to “Hold SHIFT and press MENU ▲ or ▼” to

arrive at a particular screen, you can use the alternate procedure of “Hold SHIFT while

rotating the DATA DIAL.” While both methods accomplish the same task, you may find

rotating the Data Dial preferable.

After changing system parameters in the various edit screens, pressing either MENU ▲ or

▼ will exit you back to the main screen.

AUTO CUE (Cue to Modulation)

1) This function requires use of the Memory Start feature, and its performance is

directly affected by the Auto Cue Sensitivity level

AUTO CUE SENSITIVITY LEVEL

1) Hold SHIFT and press MENU ▲ or ▼ until you arrive at screen #6 "AtcuE"

2) Press DATA, current parameter value will blink (Memory Start Standby mode must

be disengaged)

3) Rotate DATA DIAL either clockwise or counter clockwise until desired value is

displayed

4) Press SET to confirm new parameter value

CAPTURE OFFSET

1) Hold SHIFT and Press MENU ▲ or ▼ until you arrive at screen display “-tc-cLoSE”

(if display reads “oPEn”, proceed to step 3)

2) Press DATA (“cLoSE” will blink), rotate DATA DIAL to “oPEn” - press SET

3) Press MENU ▲ or ▼ until "■ CHASE OFFSET" appears in the upper right display

4) While holding SET, press CHASE - the smaller of the two Time Code displays will

be the current offset value

Note: It is assumed that Time Code is being fed to the DA-60MKII from an external

device.

To Trim or Clear the Offset:

5) Press MENU CHASE OFFSET"▲ or and select "▼ ■

6) Press DATA - the "hour" digits of the offset screen will blink and successive

presses of DATA enable you to cycle from "minutes" to "seconds" to "frames" to

"sub frames" and back to "hour"

7) Enter the desired value using the DATA DIAL and DATA key - upon completion,

press SET

CHASE LOCK SYNCHRONIZATION

1) Set CLOCK and EXT SYNC switches to the positions appropriate for your

environment and verify connections

2) For most applications, hold SHIFT and press MENU ▲ or ▼ until you arrive at

screen display "23 cHaSE XX" (XX = Free or Re-Chase), press DATA, rotate DATA

DIAL, select "rEcHASE" and press SET

3) Verify that Time Code is being fed to the DA-60MKII's Time Code IN port from the

master device

4) Press CHASE

Note: It is essential that the Time Code type is identical across all devices in the

system. If using WORD Clock, sampling frequencies must also match.

CHECK DA-60 II SYSTEM VERSIONMK

1) Displayed at Power On

COPY ID PROVISIONS

1) Hold SHIFT and press MENU ▲ or ▼ until you arrive at screen display "4 coPy"

2) Press DATA and rotate the DATA DIAL to select one of the three available options,

then press SET to confirm the operation

Note: "id-6 00" - any number of digital copies can be made

"id-6 10" - no digital copies can be made

"id-6 11" - only one digital copy is possible, copies may not be duplicated

CROSSFADE TIME

1) Hold SHIFT and press MENU or until you arrive at screen display "9 FAdE XX"▲ ▼

(XX = current value)

2) Press DATA - the current time value will blink

3) Rotate the DATA DIAL until the desired value is displayed

4) Press SET to complete this procedure

EXTERNAL TIME CODE DISPLAY

1) Press MENU ▲ or ▼ and select "■ EXT TC"

MEMO POINT CAPTURE AND AUTOLOCATE

1) As tape plays, press either MEMO 1 or MEMO 2

2) To autolocate to either memo point, press LOC 1 or LOC 2

MEMO POINT TRIM

1) Press MENU and select either " MEMO1" or " MEMO 2" (this is visible in▲ or ▼ ■ ■

the upper right of the display)

2) Press DATA- the "hour" digits of the memo address screen will blink and

successive presses of DATA enable you to cycle from "minutes" to "seconds" to

"frames" and back to "hour"

3) Using the DATA DIAL and DATA key, trim the memo address to your liking

4) Press SET to confirm the edit

Produkt Specifikationer

Mærke:	Tascam
Kategori:	Lydoptager
Model:	DA-60MKII

Har du brug for hjælp?

Hvis du har brug for hjælp til Tascam DA-60MKII stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lydoptager Tascam Manualer

Tascam DR-05XP Manual

11 Juli 2025

Tascam DR-07XP Manual

20 Februar 2025

Tascam DA-40 Manual

30 August 2024

Tascam Portacapture X8 Manual

10 August 2024

Tascam DA-98 Manual

6 August 2024

Tascam Portacapture X6 Manual

5 August 2024

Tascam DA-302 Manual

5 August 2024

Tascam MD-350 Manual

4 August 2024

Tascam LR-10 Manual

2 August 2024

Tascam DA-60MKII Manual

30 Juli 2024

Lydoptager Manualer

Nyeste Lydoptager Manualer

Steinberg Nuendo SyncStation Manual

28 September 2025

Zoom PodTrak P4 Manual

23 September 2025

DigiD Mbox 2 Manual

13 September 2025

Kodak VRC450 Manual

9 September 2025

Steren REC-854 Manual

8 September 2025

Cranborne Audio 500ADAT Manual

4 September 2025

Comica ADCaster C1 Manual

28 August 2025

IK Multimedia ToneX One Manual

22 August 2025

DBX 902 Manual

10 August 2025

Lectrosonics SPDR Manual

10 Juli 2025