Taylor 1512 Manual

Taylor Vejrstation 1512

Læs gratis den danske manual til Taylor 1512 (5 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Taylor 1512, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

WeatherGuide™ System with Remote Sensor

Models 1512 / 1512RMT

Instruction Manual

Welcome to the Taylor® WeatherGuide™ System. Simple, reliable, accurate…it allows you to monitor indoor

or outdoor locations from one room. The base unit reads indoor conditions, while the remote sensor wirelessly

reports outdoor weather conditions back to the base unit for an all-in-one weather display.

NOTE: Some units have a static cling label over the digital display. Please remove before use.

BATTERY INSTALLATION

The base unit operates on 2 AA batteries and the remote sensor operates on 2 AAA batteries (batteries not

included). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-

cad, ni-mh, etc.) batteries.

(Tip: Lithium batteries are recommended in extremely cold or hot locations.)

IMPORTANT: Install batteries in the base unit first, then the remote sensor, otherwise the units’ transmissions

may not properly connect. Place the base unit as close as possible to the remote sensor when installing batteries.

Base Unit

The battery compartment is located on the back of the unit. Remove the battery compartment door. Install (2)

AA size batteries into the battery compartment according to the polarity markings. Replace the battery

compartment door.

Remote Sensor

The battery compartment is located on the back of the unit. Slide off the battery compartment cover. Install (2)

AAA size batteries into the battery compartment according to the polarity markings. Replace the battery

compartment door.

After Batteries are Installed:

Allow at least 3 minutes for the base unit to analyze current temperature conditions and connect with the remote

sensor. A transmission signal icon (“ ”) will begin to flash on the base unit during this time. After 3 minutes,

the transmission signal will only flash when a signal is received from the remote sensor.

The remote transmits temperatures once a minute. A transmission signal icon “ ” on the remote flashes when

a signal is sent.

Note: While the base unit is in “analyzing” mode, other functions (such as switching to outdoor temperatures

and setting the clock) may not be operational. Once the “analyzing” mode is complete, the other functions will

become operational.

ADDITIONAL REMOTE SENSORS

A maximum of 3 remote sensor units can be used with the base unit; one is included. Should you purchase one

or two additional remote units (Model 1512RMT, sold separately), first install batteries in the remote, and then

press the CH button inside the remote’s battery compartment to select Channel 2 or Channel 3. The Channel

number assigned will appear on the remote’s LCD screen.

Produkt Specifikationer

Mærke:	Taylor
Kategori:	Vejrstation
Model:	1512

Har du brug for hjælp?

Hvis du har brug for hjælp til Taylor 1512 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Taylor Manualer

5 Oktober 2025

5 Oktober 2025

5 Oktober 2025

8 Januar 2025

24 August 2024

24 August 2024

24 August 2024

Taylor 5262313 Manual

24 August 2024

Taylor 1383-21 Manual

23 August 2024

Taylor 1511 Manual

23 August 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

Alecto WS5100 Manual

3 November 2025

Denver WSR-560 Manual

2 November 2025

Govee H5179001 Manual

25 Oktober 2025

Lexibook Serenity RL930 Manual

20 Oktober 2025

Sempre GT-WS-11wUK Manual

13 Oktober 2025

ClimeMET CM9088 Manual

2 Oktober 2025

La Crosse Technology WS7006 Manual

30 September 2025

Livoo SL265 Manual

23 September 2025

Livoo SL264 Manual

23 September 2025

Livoo SL263 Manual

23 September 2025