TK Audio M/S Station Manual

TK Audio Ikke kategoriseret M/S Station

Læs gratis den danske manual til TK Audio M/S Station (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om TK Audio M/S Station, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

M/S Staon

Advanced M/S tool

www.tkaudio.se

The M/S Staon is a new mastering and main bus tool with four separate funcons divided into two sec-

ons including an advanced cue funcon.

Secon 1 is a parallel insert with M/S funcon allowing the user to use separate blend controls for the mid

and side signals. For maximum precision the blend control(s) has 16 posions from dry to wet.

Secon 2 consists of three parts, an ellipcal EQ with 16 frequencies, a width control from 0-200% and an

advanced cue funcon.

The two secons are normally linked internally but can be used separately with their own balanced inputs

and outputs by removing four jumpers inside the unit (see unlink secon 1 and 2). This way you can use

them at dierent locaons in your setup.

Parallel insert with M/S funcon:

With the insert secon you can insert an external

processor like an EQ, compressor, distoron unit

etc, and then dial in a mix between the processed

signal (wet) and the unprocessed signal (dry).

For maximum precision the blend control has 16

steps from dry to wet.

If you acvate the M/S funcon your signal will

be coded into mid ( L+R ) and side ( L-R ). The mid

signal normally contains all the center info such

as bass, kick drum, lead vocal etc and the side

signal contains all the panned parts of the signal.

In M/S you can process the mid signal and side

signal separately with dierent types of proces-

sors and the blend controls is placed infront of

the M/S encoder before it’ decoded back to le

and right signals.

With the blend split funcon you get separate

blend controls for the mid and side signal.

Ellipcal Equalizer:

With the ellipcal EQ all frequencies below a

selected frequency will be made to mono. This

funcon can make your low end more focused.

It’s an old technique used when mastering for

vinyl.

Too much low end in the side channel (vercal)

can make the needle bounce slightly and cause

distoron.

By using a 12dB high pass lter in the side chan-

nel you set the frequency under which the signal

will be processed as mono. As a HPF introduces

phase shi to the signal, a phase correcon

is added to the mid channel keeping channel

separaon as good as possible. The EEQ has 16

frequencies from 36Hz to 302Hz.

With the EEQ cue funcon you can monitor the

signals that are mixed between the channels.

www.tkaudio.se

Stereo width control:

By adjusng the amount of side informaon in

the stereo mix, the width can be adjusted in-

crementally from mono to extra wide. With this

control you can ne adjust the stereo image aer

you have used the M/S insert and EEQ.

Cue funcon:

When powered on the Stereo cue is auto selec-

ted as this is the normal operaon stage.

With the cue funcon you can monitor the Le,

Right, Mid or Side signal separately by pressing

the dedicated buon.

When you run the parallel insert in M/S and

Blend Split is acvated ”Insert cue” is a dedicated

funcon to monitor the Mid or Side blend sepa-

rately. The signal is then sent to the cue secon

without passing the EEQ, width circuit or other

gear if the M/S Staon is used unlinked.

With Insert cue acvated the L or R cue buon

will act as Mid or Side cue buons. By pressing

the L cue buon you will monitor the Mid blend

and by pressing the R cue buon you will monitor

the Side blend.

The ”Insert cue” funcon can be used even if

you run the two secons separately at dierent

locaons in your chain.

You can NOT use the ”Insert cue” funcon to

monitor the insert blend in stereo. This funcon

is dedicated to monitor the Mid or Side signals in

M/S mode with split blends only!

If you select the EEQ buon on the cue secon

you can monitor the low frequencies fed from

le to right or right to le by pressing L or R cue

switch. Perfect for ne tuning of the EEQ seng.

Produkt Specifikationer

Mærke:	TK Audio
Kategori:	Ikke kategoriseret
Model:	M/S Station

Har du brug for hjælp?

Hvis du har brug for hjælp til TK Audio M/S Station stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret TK Audio Manualer

TK Audio Transformer Manual

28 September 2025

TK Audio SP502 Manual

15 September 2025

TK Audio T-Komp 500 Manual

3 Marts 2025

TK Audio DP3 Manual

26 Januar 2025

TK Audio T-Komp Manual

3 September 2024

TK Audio TK-lizer 2 Manual

3 September 2024

TK Audio TK-lizer 500 Manual

28 August 2024

TK Audio M/S Station Manual

28 August 2024

TK Audio BC1-THD Manual

27 August 2024

TK Audio BC501-GR Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025