Tokina SZX SUPER TELE 400mm F8 Reflex MF Manual

Tokina Linse SZX SUPER TELE 400mm F8 Reflex MF

Læs gratis den danske manual til Tokina SZX SUPER TELE 400mm F8 Reflex MF (1 sider) i kategorien Linse. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Tokina SZX SUPER TELE 400mm F8 Reflex MF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

2. Attaching the lens to the camera

Align the indicator marks on the mount adapter and the

camera body, and then turn the lens until you hear a “click.”

(For attachment and removal, refer to “Attaching the Lens”

and “Removing the Lens” in your camera's manual.)

Make sure the lens is firmly attached.

CameraMount adapter

10 12 15 20 30 50 100 ftMACRO

3 3.5 4 5 6 8 10 15 30 m1:3.5 1:4 1:4.5

1. Part names

Lenswithmountadapterremoved

Fig. 1

Fig. 2

10 12 15 20 30 50 100 ftMACRO

3 3.5 4 5 6 8 10 15 30 m1:3.5 1:4 1:4.5

⑤ ⑥ ⑧④

⑦

⑨

10 12 15 20 30 50 100 ftMACRO

3 3.5 4 5 6 8 10 15 30 m1:3.5 1:4 1:4.5

①

②

(Inside)

③

＊ Theshapeofthemountadaptermayvary

dependingoncameraspeciﬁcations.

① Mount adapter attachment thread

② Filter attachment thread (rear)

③ Filter attachment thread (front)

④ Focus ring

⑤ Distance scale (in feet)

⑥ Distance scale (in meters)

⑦ Macro magnification scale

⑧ Distance scale indicator mark

⑨ Mount adapter

3. Mount adapter

⑩ Outer screw (x3)

⑪ Outer ring

⑫ Inner ring

In order to adjust the position of the lens or attach rear filter

you have to adjust the mount adapter.

Follow the instructions below to adjust the position or

remove the mount adapter:

Slightly loosen the outer screws

(

⑩

)

as shown in Fig. 2.

＊ Do not loosen the screws too much. It may cause the inner ring

of the mount adapter to come off.

＊ Use a regular precision screwdriver to loosen the screws.

Turn the lens until the distance scale indicator comes to the top

center, and then securely tighten the outer screws

(

⑩

)

shown in Fig. 2.

Take the lens off the camera.

Remove the mount adapter from the lens by turning the mount

adapter counterclockwise while holding the lens with the other

hand.

Note : If the outer

screws

(

⑩

)

are

loosened too

much, the inner ring

(

⑫

)

may come off.

If the distance scale indicator mark

(

⑧ in Fig. 1

)

does not

align with the top center of the lens when it is attached to

the camera, adjust according to the instructions below:

Note : For easier operations, the 3 exterior screws are slightly

loosened at the time of shipment. Make sure

beforehand that you use screwdriver to tighten p1-he

screws before attaching the mount to the lens.

Follow the instructions below to remove the mount adapter

from the lens:

⑩

⑩⑩

⑪

⑫

＊ The shape of the mount adapter may vary

depending on camera specifications.

4. Setting up the camera

Some cameras must be set up before attaching the lens.

Set up your camera by referring to the information provided

below. For details, refer to your camera's manual.

For correct using and setting of the camera’s in-built image

stabilization, refer to your camera's manual.

The lens can be used in the “Av (aperture priority)” mode and “M

(manual)” mode.

■

How to use the “Av (aperture priority)” mode

1. Set the exposure mode to “Av.”

2. Correct the exposure compensation if necessary.

If this lens is used with a Canon EOS series camera, the following

operations may be required on some models due to the specifica-

tions of the camera:

Canon EOS series

• When the lens is attached, the aperture is displayed as “00.”:

You can shoot as it is.

• An aperture value (e.g., F5.6) is displayed when the lens is

attached:

Open up the aperture (adjust it to the smallest value).

＊This lens cannot be used with those cameras that have no aperture

priority mode (Av) or manual mode (M).

＊If a conversion lens or an extension tube (ring) is attached, the

camera will not operate correctly. Do not combine this lens with the

above items.

＊The Focus Aid function cannot be used.

＊The aperture cannot be adjusted in the aperture priority mode.

＊The aperture value will not be recorded in Exif data.

SONY E

The supported exposure modes might be limited depending on the

camera model.

Refer to “List of Supported Non-CPU Lenses” or other similar sec-

tions in your camera's manual.

Nikon F

To use this lens with any cameras listed above, set the shooting

mode to “M (manual).”

The shutter cannot be released in any other mode.

＊The shutter speed must be adjusted depending on the condition in

which photographs are taken.

＊Set the focus mode to “MF.”

＊The aperture cannot be adjusted in the aperture priority mode.

＊The aperture value will not be recorded in Exif data.

D5XXX series, D3XXX series, D90, D80, D60, D40X, D40,

D70S, D70, D50, D100

The non-lens release lock function must be canceled.

Menu 󲰛Setup Menu 󲰛Change the setting for [Release without

Lens] to [Permit].

Any shooting mode can be used, except for those in which priority is

given to the shutter speed. It is not recommended to give priority to

the shutter speed (shutter priority mode).

＊ In the program mode, aperture priority mode or manual mode, set

the ISO sensitivity to AUTO.

Menu Setup Menu Brightness/Color ISO Sensitivity 󲰛 󲰛 󲰛 󲰛

Set to [AUTO].

＊ The aperture cannot be adjusted in the aperture priority mode.

＊ The aperture value will not be recorded in Exif data.

Olympus Micro Four-Thirds

Any shooting mode can be used, except for those in which the

shutter speed is given priority (shutter priority mode). It is not

recommended to give priority to the shutter speed (shutter priority

mode).

＊

When using the program mode, aperture priority mode or manual

mode, set the ISO sensitivity to AUTO.

Setup Menu ISO Sensitivity Set to [AUTO].󲰛 󲰛

＊ The aperture cannot be adjusted in the aperture priority mode.

＊ The aperture value will not be recorded in Exif data.

Panasonic Micro Four-Thirds

The non-lens release function must be set to [ON].

Setup Menu Release without Lens Set to [ON].󲰛 󲰛

Any shooting mode can be used, except for those giving priority to

the shutter speed (shutter priority mode). It is not recommended to

give priority to the shutter speed (shutter priority mode).

＊ When using the program mode, aperture priority mode or manual

mode, set the ISO sensitivity to AUTO.

Setup Menu ISO Sensitivity Set to [AUTO].󲰛 󲰛

＊ The aperture cannot be adjusted in the aperture priority mode.

＊ The aperture value will not be recorded in Exif data.

FUJIFILM X

It is necessary to set menu allowing [Release without lens] option to

be activated.

Setup Menu Release without lens [Approval]󲰛 󲰛

Shooting can be possible in aperture priority AE mode or manual (M)

mode.

＊ Set ISO to [AUTO] MENU ISO [AUTO]󲰛 󲰛

＊ Aperture value will not be registered in Exif data.

＊

In “Movie” mode there is no [Release without lens] option in menu

list, but if in other mode [Release without lens] is approved, movie

function will be activated.

400mm

F8 (fixed)

Full Frame (24mm x 36mm)

Multi-coated

6 elements in 5 groups

6° 8’

1.15 m

0.4x

Manual with front barrel extension

67 mm

30.5 mm

76.8mm (at infinity position)

φ74 mm

355 g

BH-673

Focal distance

Maximum aperture

Format

Coating

Lens configuration

Angle of view

Minimum focus distance

Maximum macro magnification

Focus

Diaphragm blades

Front filter size

Rear filter size

Overall length

(excluding mount adapter)

Maximum diameter

Weight

(excluding mount adapter)

Hood

6. Specifications

＊ Before attaching a filter to the front of the lens, be sure the filter will not get in contact

with the reflective part (black circle) at the center of the front surface of the lens.

Specifications and exterior appearance are subject to change without previous notice

for the purpose of product improvement.

＊ A display mark indicating inclusion in the China RoHS directive (Administrative

Measure on the Control of Pollution Caused by Electronic Information Products).

A lens hood is designed to prevent the flares

and ghost in the images that may be caused

by strong diagonal or side rays hitting the lens.

We recommend using a lens hood to ensure

high quality images and protect the lens.

Lens hood is a screw type hood. To securely

install the hood turn it according to the arrow

as shown in the picture below. To remove

the hood, turn it in the opposite way.

5. Lens Hood

How to attach the lens hood

10 12 15 20 30 50 100 ftMACRO

3 3.5 4 5 6 8 10 15 30 m1:3.5 1:4 1:4.5

BH-673

T4008-2006

SZX SUPER TELE 400mm F8

Reflex MF

Instruction Manual

This is a telephoto lens for a single-lens

reflex cameras or interchangeable lens

mirrorless digital cameras adopting

reflective optics to achieve a long focal

length within a compact body.

Produkt Specifikationer

Mærke:	Tokina
Kategori:	Linse
Model:	SZX SUPER TELE 400mm F8 Reflex MF
Vægt:	355 g
Brugervejledning:	Ja
Produktfarve:	Sort
Pakketype:	Kasse
Diameter:	74 mm
Grænseflade til montering af objektiv:	Canon RF
Fokusindstilling:	Vejledning
Oprindelsesland:	Japan
Længde:	77 mm
Zoom kapacitet:	Ingen
Nærmeste fokuseringsafstand:	1.15 m
Maksimale blænderåbning tal:	8
Komponent til:	MILC/SLR
Kameramærker kompatibilitet:	Canon
Objektivstruktur (elementer/grupper):	6/5
Objektivtype:	Teleobjektiv
Filterstørrelse:	67 mm
Mindste blænderåbnimg tal:	8
Modlysblænder:	Ja
Modlysblænde type:	Aftagelig linsehætte
Objektivdæksel inkluderet:	Ja
Objektivets synsvinkel, vandret:	6°8' °
Garantiperiode:	2 År
Makroforhold:	1:2.5
Bageste linsehætte medfølger:	Ja
Modlysblænde model:	BH-673
Linseadapter inkluderet:	Ja