TP-Link Archer NX600 Manual

TP-Link Router Archer NX600

Læs gratis den danske manual til TP-Link Archer NX600 (2 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13 anmeldelser. Har du et spørgsmål om TP-Link Archer NX600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Customize the 5G Router

Note: The router can also be used (or configured) in EWAN Mode(wireless router

mode) for Cable connections. For more advanced configurations, please refer to

the user guide on TP-Link official website at www.tp-link.com.

Note: If the login page does not appear, please refer to Q1 of Need Help? in this

guide.

2 .Launch a web browser and type in orhttp://tplinkmodem.net

http://192.168.1.1. Create a new password for future logins.

3. Follow the step-by-step instructions of the to complete the Quick Setup

initial conguration.

1. Make sure your computer is connected to the router (wired or wireless).

http://tplinkmodem.net

HighMiddleLow

Save

Conrm Password

New Password

Need Help?

Q1. What should I do if I cannot access the web management page?

• If the computer is set to a static IP address, change its settings to obtain an IP address automatically.

• Make sure or is correctly entered in the web browser.http://tplinkmodem.net http://192.168.1.1

• Use another web browser and try again.

• Reboot your router and try again.

• Disable and enable the active network adapter in use.

Q2. What should I do if I cannot access the internet?

• Verify that your SIM card is a 5G/4G or WCDMA card.

• Verify that your SIM card is in your internet service provider’s service area.

• Verify that your SIM card has sufficient credit.

• Check the LAN connection: Open a web browser and enter or http://tplinkmodem.net

http://192.168.1.1 in the address bar. If the login page does not appear, refer to Q1 and then try again.

• Launch a web browser, log in to the web management page, and check the following:

1) Go to Advanced Network Mobile WAN > > to verify the parameters provided by your ISP are correctly

entered. If the parameters are incorrect, click Create Profile and enter the correct parameters, then

select the new profile from the list.Profile Name

2) Go to Advanced Network PIN Management > > to verify if PIN is required. If it is, enter the correct PIN

provided by your ISP, and click .Save

3) Go to Advanced Network Data Settings > > to verify if the Total/Monthly Used exceeds the

Total/Monthly Allowance Correct. If it does, click and set Total/Monthly Used to 0 (zero), or disable

Data Limit.

4) Go to Advanced Network Mobile WAN Mobile Data > > to verify that is enabled. If it is not, enable it to

access the internet.

5) Confirm with your ISP if you are in a roaming service area. If you are, go to Advanced Network > >

Mobile WAN Data Roaming to enable .

6) Confirm the selection of Antenna Type.

If it is determined that an external antenna is connected, select External 5G/LTE Antennas.

If you are sure that no external antenna is connected, select Internal 5G/LTE Antennas.

Q3. How do I restore the router to its factory default settings?

• With the router powered on, press and hold the button on the rear panel of the router until the RESET

Power LED starts flashing, then release the button. Wait while the router resets.

• Log in to the web management page of the router, and go to Advanced System Tools Backup & > >

Restore Factory Restore, click and wait until the reset process is complete.

Q4. What should I do if I forget my web management page password?

• If you are using a TP-Link ID to log in, click Forgot password on the login page and then follow the

instructions to reset it.

• Alternatively, refer to to reset the router, then create a new password to log in. Q3

Q5. What should I do if I forget my wireless network password?

• The default wireless password is printed on the product label of the router.

• Connect a computer directly to the router using an Ethernet cable. Log in to the router's web

management page and go to > Basic Wireless to retrieve or reset your wireless password.

Q6. What should I do if I want to change the LAN/WAN port from default WAN port to LAN port?

• Log in to the web management page of the router, and go to Advanced Network Internet > > to delete

the prole from the Internet Setup list and click Save. Then the default WAN port will change to LAN

port.

For technical support, replacement services, user guides, and other information, please visit

https://www.tp-link.com/support, or simply scan the QR code.

Safety Information

• Keep the device away from water, re, humidity or hot environments.

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Do not use damaged charger or USB cable to charge the device.

• Do not use any other chargers than those recommended.

• Do not use the device where wireless devices are not allowed.

• Adapter shall be installed near the equipment and shall be easily accessible.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant

provisions of directives 2014/53/EU, 2009/125/EC, 2011 /65/EU and (EU) 2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant

provisions of the Radio Equipment Regulations 2017.

The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

UK Declaration of Conformity

Quick Installation Guide

5G CPE Router

Connect the Hardware

b. Connect the

power adapter

and turn on the

router.

Power adapter

a. With the gold contacts

facing right, insert the

nano SIM card into the slot

until you hear a click.

Nano

SIM Card

Note: The RESET button is actually a shared RESET/Wi-Fi button (short press for 5 seconds or less is

for Wi-Fi function, long press for 5 seconds or more is for RESET function). A short press will cause

the Wi-Fi in use to turn o.

Verify the Hardware Connection Enjoy the Internet

Wireless

Wired

Connect your computers to the router's LAN ports via Ethernet cables.

Find the SSID (network name) and wireless password printed on the

label at the bottom of the router.

Click the network icon of your computer or go to Wi-Fi settings of your

smart device, and then select the SSID to join the network.

IMEI:XXXXXXXXXXXXXXX

MAC:XX-XX-XX-XX-XX-XX

Wireless Password/PIN:XXXXXXXX

SSID:TP-Link_XXXX

Power: 12V 2A

Note: The LAN/WAN port defaults to WAN port. Please refer to Q6 of Need Help? in this guide

if you want to change it to LAN port.

Congure the router via Tether App

The TP-Link Tether app provides a simple, intuitive way to access and manage

your router.

View information about clients

connected to your router

Block unwelcome users from

connecting to your network

Set up Parental Controls

with access time

Change the basic wireless

network settings

Note: If you don’t have an account, create one rst.

1. Download the TP-Link Tether app.

2. Open the Tether app and log in with your TP-Link ID.

3. Tap the icon in the Tether app and select 4G/5G Router.

Follow the steps to complete the setup and connect to the internet.

How to begin?

*Images may dier from actual products.

LED Status Indication

On/O

Flashing

On/O

O

On/O

Flashing

Power is on or o.

The system is starting up or rmware is being upgraded.

Do not disconnect or power o your modem router.

Wi-Fi is enabled or disabled.

WPS connection is in progress. This may take up to 2

minutes.

At least one LAN port is connected.

No LAN port is connected or LAN port is not

connected properly.

The signal strength is above 75%.

The signal strength is between 50% and 75%.

The signal strength is below 50%.

No mobile network signal.

(Power)

(Internet) Internet service is available or unavailable.

(Signal

Strength)

(Network

Type)

(Wi-Fi)

Solid white

Solid green

Solid yellow

O

The device is on a 5G/4G+ network (depend on the router).

The device is on a 4G network.

The device is on a 3G network.

The device is not registered on the network.

Solid white

Solid green

Solid yellow

O

(LAN)

Check the following LEDs’ status. If the Internet LED is on, your router is

connected to the internet successfully.

Note: If the Internet LED does not turn on, please refer to Q2 of Need Help? in this guide.

12 3

Note: Due to Tether app updates, your actual user interface and pathway may dier from those

depcited here.

Produkt Specifikationer

Mærke:	TP-Link
Kategori:	Router
Model:	Archer NX600

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link Archer NX600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Router TP-Link Manualer

TP-Link Archer BE550 Pro Manual

9 Marts 2025

TP-Link Deco X1500-4G Manual

10 Januar 2025

TP-Link Archer NX600 Manual

1 Januar 2025

TP-Link Archer MR505 Manual

2 December 2024

TP-Link Archer AXE75 Manual

14 Oktober 2024

TP-Link Archer C2600 Manual

5 Oktober 2024

TP-Link Archer AX95 Manual

3 Oktober 2024

TP-Link Archer MR500 Manual

26 September 2024

TP-Link Deco X10 Manual

18 September 2024

TP-Link SafeStream TL-R480T+ Manual

15 September 2024

Router Manualer

Nyeste Router Manualer

6 Juni 2025

4 Juni 2025

31 Maj 2025

8 April 2025

WyreStorm EXP-SW-0401-H2 Manual

22 Marts 2025

Devolo WiFi 6 Router 3600 5G LTE Manual

6 Marts 2025

Huawei E5785-320 Manual

23 Februar 2025

Huawei E5785-330 Manual

23 Februar 2025

Xiaomi Router AX3000T Manual

22 Februar 2025

Huawei E5180 Manual

20 Februar 2025