V-TAC VT-5413 Manual

V-TAC Dørklokke VT-5413

Læs gratis den danske manual til V-TAC VT-5413 (1 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om V-TAC VT-5413, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
WIFI DOORBELL (CHIME)
TECHNICAL DATA
INTRODUCTION
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read
these instructions carefully before starting the installing and keep this manual handy for future
reference. If you have any another query, please contact our dealer or local vendor from whom
you have purchased the product. They are trained and ready to serve you at the best.
WARNING!
1. Please make sure to turn off the power before starting the installation.
1. Check that your mains supply is correct for the doorbell receiver.
2. The receiver is for indoor use only. Do not use outside or allow to become wet.
3. There are no user-serviceable parts. Do not attempt to repair either the transmitter or the
receiver by yourself.
THE FIRST USE GUIDE:
1. Plug the receiver into a mains socket and switch the socket on.
2. Press the transmitter push button and confirm that the transmitter indicator flashes, the doorbell
receiver sounds “Ding-Ding” and the receiver indicator flashes. The doorbell is paired. The default
ringtone is “Ding-Dong”. Users can change the ringtone easily, just refer to the “CHANGING THE
RINGTONE” steps.
CHANGING THE RINGTONE / PAIRING:
Step 1: Press the Backward or Forward button on the receiver to choose your favorite melody.
Step 2: Press and hold down the Volume button on the receiver for 5 seconds, until it makes a
“Ding” sound and the receiver indicator flashes (that means the doorbell entered into the Pairing
Mode, the pairing mode will only last 8 seconds, then it will automatically exit).
Step 3: Press the button on the transmitter quickly, it will makes a “Ding-Ding” sound and the
receiver indicator flashes.
Step 4: Press the button on the transmitter again to confirm whether the current ringtone is the one
you have set, if yes, the pairing is completed.
Remark: This method is also suitable for adding/pairing additional transmitters.
CLEARING THE SETTINGS:
Press and hold down the Forward button on the receiver for 5 seconds,
until it makes a “Ding” sound and the receiver indicator flashes, all the
settings will
be cleared, the doorbell will back to the factory default settings (it means
that the ringtone you have set and the transmitters you have add-
ed/paired will be cleared).
INSTALLATION:
1. Plug the receiver into a mains socket and switch the socket on.
2. Place the transmitter exactly where you intend to fix and, with the doors closed, confirm that the
doorbell receiver still sounds when you press the transmitter push button ( If the doorbell receiver does
not sound, this may be due to metal within the fixing surface and you may need to reposition the
transmitter ).
3. Fix the transmitter in place with bracket.
ADJUSTMENTS:
1. The volume of the doorbell may be adjusted to one of five levels. Press the Volume button on the
receiver to increase the volume by one level, the receiver will sound to indicate the selected level. If the
maximum level is already set, the doorbell will switch to the minimum level, which is the Silent Mode.
2. The melody played by the doorbell may be set to any one of 55 different selections. Press the Back-
ward or Forward button to select the next available melody, the receiver will sound to indicate the
selected melody. To set the doorbell ringtone to the selected melody, please refer to the “CHANGING
THE RINGTONE” steps.
CHANGING THE BATTERY:
1. Insert the Mini Screwdriver in the cover slot at the bottom of the transmitter and twist to release the
transmitter from the cover.
2. Remove the exhausted battery and dispose of properly.
3.Insert the new battery into the battery compartment. Observe
correct battery polarity (+ve and -ve), or the unit will not function and may be damaged.
4. Refit the transmitter to the cover, with the push button at the bottom.
In case of any query/issue with the product, please reach out to us at: support@v-tac.eu
For More products range, inquiry please contact our distributor or nearest dealers.
V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
This marking indicates that this product should
not be disposed of with other household wastes.
RECEIVER
PRODUCT DIAGRAM
TRANSMITTER
Speaker
AC Plug
Volume
Backward
Forward
Indicator Light
Light Sensor PIR
HD 720P
Camera Lens AC Input Hole
Stuck Hole
Security Screw
Backet Screws
Hole
BRACKET
STEP 1 STEP 2 STEP 3 - 4
IP55
RATING
INPUT POWER BATTERY OPERATION
TEMPERATURE
IP
RATING
NO OF
RINGTONES
OBJECT
DISTANCE
DECIBEL
LEVELS
AC:110-260V 3.7V, 3400 mAH -30°C to 70°C /
-22°F to 158°F IP55 55 1000 FT. /
300M
0-110 DB, 5
LEVELS

Produkt Specifikationer

Mærke: V-TAC
Kategori: Dørklokke
Model: VT-5413

Har du brug for hjælp?

Hvis du har brug for hjælp til V-TAC VT-5413 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Dørklokke V-TAC Manualer

V-TAC

V-TAC VT-5413 Manual

8 August 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Heidemann

Heidemann 70519 Manual

14 September 2025
Cata

Cata CORONA WH 60 Manual

11 September 2025
Cata

Cata LEGEND 7000 XGBK Manual

11 September 2025
Cata

Cata THALASSA 900 GBK Manual

11 September 2025
Cata

Cata GOYA PRO 90 BK Manual

11 September 2025
Cata

Cata GOYA 70 BK &ROCA Manual

11 September 2025
Cata

Cata TFB-5150 X Manual

11 September 2025
Cata

Cata GRECO 80 WH &ROCA Manual

11 September 2025
Cata

Cata THALASSA PRO 600 GBK Manual

11 September 2025
Cata

Cata GOYA 90 WH &ROCA Manual

11 September 2025