Velleman KNS4 Manual

Velleman Legetøj KNS4

Læs gratis den danske manual til Velleman KNS4 (7 sider) i kategorien Legetøj. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Velleman KNS4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

KNS4 VELLEMAN 1

KNS4 – COPTERMECH

1. Introduction & Characteristics

Thank you for buying the KNS4 ! Read this manual carefully before bringing the device into use.

• Familiarise yourself with the operation of transmissions steered through gears or pulleys.

• Easy to build, no glue or soldering required.

• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper

included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

Note that the figures with the assembly instructions can be found in the second folder “KNS4 – Figures”!!!

2. Parts List

Part n° Quant. Description Part n° Quant. Description

1 1 motor holder

12 2 fixing plate

2 1 battery holder 13 3 PVC tube (1.5 x 15mm)

3 1 motor with wire 14 3 metal shaft (2 x 90mm)

4 15

1 slide switch with wire 3 metal shaft (2 x 70mm)

5 1 plastic tube (L : 15cm) 16 1 belt (black) (126 x 1mm)

6 17 1 metal shaft (2 x 40mm) 1 rubber band (35mm, red)

7 1 pinion gear 18 4 rubber band (40mm red)

8 19 1 face gear 36T/14T (white) 7 fixing plate (L-shaped)

9 20 2 pulley 19.5 x 2mm (blue) 15 nylon pad

10 8 pulley 15 x 2mm (yellow) 21

11 nylon pad

11 22 2 pulley 24 x 2mm (white) 26 self-tapping screw

3. Prepunched Boards (see “KNS4 – Figures

”

)

4. Assembly (see also “KNS4 – Figures

”

)

Fig. 4 : Insert part n°20 in the hole on board n°2 and mount the motor holder according to fig. 4.

Fig. 5 : Insert part n°20 (x 8) in boards n°1 & 4. Insert part n°7 between boards 1 & 4. Insert 2 x part n°15 in board

n°4 and through the pulley (part n°10). The metal shafts come out the other side of board n°1. Remember

to put the rubber bands (parts n°18 & 16) on the pulley before inserting the metal shaft. Another part n°15

goes through boards n°1 & 4.

Fig. 6 : Cut part n°5 to precisely 32mm. Insert part n°20 in board n°5 first, then put metal shaft n°14 through board

n°5. Mount part n°5 & 8 according to figure 6. Attach board n°5 to boards n°1 & 4 with part n°19.

KNS4 VELLEMAN 2

Fig. 9 : Observe a distance of 10mm between board n°20 and the pulley (part n°10).

Fig. 10 : Fix board n°10 to board n°3 with part n°19.

Fig. 12 : Screw the battery holder (n°2) to the underside of board n°2. The wires pass through board n°2 to make

the connection with the motor and the switch (see fig. 16).

Fig. 13 : Gives a state of affairs.

Fig. 14 : Use one part n°12 to fix boards n°11 & 17 and use a second one to fix boards n°11 & 16.

4. Troubleshooting

• Make sure the wiring is correct

• Note that all shafts (n°6, 14 & 15) in nylon pads (n°20 & 21) should be able to move. This will allow the pulleys &

wheels to run smoothly.

Note : The specifications and contents of this manual can be subject to change without prior notice.

KNS4 – COPTERMECH

1. Inleiding en Kenmerken

Dank u voor uw aankoop ! Lees deze handleiding aandachtig voor u het toestel in gebruik neemt.

• Leer hoe een tandwielaandrijving of een pulley met riemaandrijving werkt.

• Makkelijk te bouwen, zonder lijm of solderen.

• Maak de voorgesneden vormen pas los wanneer u ze nodig hebt. Schuur de scherpe randjes af voor gebruik

(schuurpapier meegeleverd)

• De kit wordt aangedreven door 2 AA-batterijen (niet inbegrepen).

De kits van de KNS-reeks worden geleverd met voorgesneden vormen, tandwielkast, koppeling, stangen,

schakelaar, motor, batterijhouder en alle vereiste onderdelen.

U vindt de figuren met de montagetips in de tweede folder : “KNS4 – Figuren”!!!

2. Lijst van onderdelen

Nr. Hoev. Beschrijving Nr. Hoev. Beschrijving

1 1 motorhouder 12 2 bevestigingsplaat

2 1 batterijhouder 13 3 PVC buis (1.5 x 15mm)

3 1 motor met draad 14 3 metalen as (2 x 90mm)

4 1 glijschakelaar met draad 15 3 metalen as (2 x 70mm)

5 1 plastic buis (L : 15cm) 16 1 riem (zwart) (126 x 1mm)

6 1 metalen as (2 x 40mm) 17 1 aandrijfriem (35mm, rood)

7 1 rondsel

18 4 aandrijfriem (40mm rood)

8 19 1 tandwiel 36T/14T (wit) 7 bevestigingsplaat (L-vormig)

Produkt Specifikationer

Mærke:	Velleman
Kategori:	Legetøj
Model:	KNS4

Har du brug for hjælp?

Hvis du har brug for hjælp til Velleman KNS4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Legetøj Velleman Manualer

Velleman KNS130 Manual

10 August 2025

Velleman VMA500 Manual

4 December 2024

6 Oktober 2024

1 Oktober 2024

15 Februar 2023

8 December 2022

6 December 2022

Legetøj Manualer

Nyeste Legetøj Manualer

Playmobil Animals & Friends 71855 Manual

12 August 2025

Playmobil Sky Trails 71972 Manual

12 August 2025

Atomic M01702AW Manual

12 August 2025

Playmobil Animals & Friends 71854 Manual

12 August 2025

Playmobil Junior 71777 Manual

12 August 2025

Lorelli Piano Manual

12 August 2025

Playmobil City Action 71875 Manual

12 August 2025

Playmobil Heroes 71835 Manual

12 August 2025

Playmobil Heroes 71831 Manual

12 August 2025

Playmobil My Life 71905 Manual

12 August 2025