Velleman KNS8 Manual

Velleman Legetøj KNS8

Læs gratis den danske manual til Velleman KNS8 (8 sider) i kategorien Legetøj. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Velleman KNS8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

KNS8 VELLEMAN 1

KNS8 – MECHANICAL SKELETON

1. Introduction & Characteristics

Thank you for buying the KNS8 ! Read this manual carefully before bringing the KNS8 into use.

• Build a gearbox and learn how automatic transmissions and motors work.

• Easy to build, no glue or soldering required.

• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper

included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

Note that the figures with the assembly instructions can be found in the second folder “KNS8 – Figures”!!!

2. Parts List (see also KNS8 – Figures)

Part n° Quant. Description Part n° Quant. Description

1 1 gearbox 18 6 nylon nut M3

2 1 motor 3Vdc 19 18 nut M2

3 1 battery holder 20 18 screw (2 x 8mm)

4 21 1 slide switch with wire 4 self-tapping screw (2 x 4mm)

5 22 1 metal shaft (2 x 40mm) 2 screw (3 x 14mm)

6 23 1 metal shaft (3 x 52mm) 2 screw (3 x 18mm)

7 1 pinion gear 8T 24 2 screw (3 x 22m)

8 25 1 face gear 36T/10T (white) 8 washer (3.2 x 10.0 x 0.5mm)

9 26 1 gear 40T/0T (white) 15 washer (2.6 x 6.0 x 0.5mm)

10 1 gear 40T/10T (red) 27 3 PVC tube (15mm)

11 1 gear 40T/10T (green) 28 10 nylon pad (Ø 8mm)

12 29 1 wire with terminal (yellow) 5 fixing plate (L-shaped)

13 30 1 wire with terminal (green) 4 nylon post (H : 3mm)

14 2 metal foot (U-shaped) 31 1 spring (L : 50mm)

15 32 2 nylon connector (N-shaped) 2 spring (L : 20mm)

16 2 nylon pad (5.6 x 4.8 x 1.95) 33 6 self-tapping screw (2 x 6mm)

17 2 nylon post (H : 6mm)

3. Prepunched Boards (see “KNS8 – Figures

”

)

4. Assembly (see also “KNS8 – Figures

”

)

Fig. 3 : The gears (n°9/10/11/8) should be placed to the left of the pinion gear. One N-shaped nylon connector

(n°15) should point downward and the other one upward. Insert the motor as depicted in the drawing. Note

that the protruding edge should point towards the metal case.

Fig. 4 : Identify boards 2 & 3. The screw opening in board 3 is located in the middle, while the one in board 2 lies

off to the left. Make sure board 1 is not upside-down.

KNS8 VELLEMAN 2

Fig. 5 : Screw the gearbox to the upside of board 11. Consult the figure for the position of the opening.

Fig. 7 : Screw the battery holder to board 11.

Fig. 8 :* = left, ** = right.

Fig. 9 : Don’t screw the arms down too tightly. A somewhat looser fit enables your mechanical skeleton to move

more smoothly.

Fig. 10 : Don’t screw the legs down too tightly. A somewhat looser fit enables your mechanical skeleton to move

more smoothly.

Fig. 12 : The U-shaped metal foot should be flush with the ground. Note : * = left, ** = right.

Fig. 13 : Fix the spring (piece n° 32) to the right side of the head under the angle depicted in the figure.

Fig. 14 : Attach boards 21 & 22 to board n° 1. Mount board 23 next.

5. Troubleshooting (see also “KNS8 – Figures”)

• Make sure the wiring is correct

• Adjust the screws on the legs and arms if the KNS8 doesn’t move even though the motor is running.

• Bend the U-shaped metal feet slightly (see figure 16) to make the KNS8 move more smoothly.

Note : The specifications and contents of this manual can be subject to change without prior notice.

KNS8 – MECHANISCH SKELET

1. Inleiding & Kenmerken

Dank u voor uw aankoop ! Lees deze handleiding aandachtig voor u de KNS8 in gebruik neemt.

• Bouw een tandwielkast en leer hoe een automatische overbrenging en een motor werken.

• Maak de voorgesneden vormen pas los wanneer u ze nodig hebt. Schuur de scherpe randjes af voor gebruik

(schuurpapier meegeleverd)

• De kit wordt aangedreven door 2 AA-batterijen (niet inbegrepen).

De kits van de KNS-reeks worden geleverd met voorgesneden vormen, tandwielkast, koppeling, stangen,

schakelaar, motor, batterijhouder en alle vereiste onderdelen.

U vindt de figuren met de montagetips in de tweede folder : “KNS8 – Figuren”!!!

2. Lijst van onderdelen

Nr. Hoev. Beschrijving Nr. Hoev. Beschrijving

1 1 tandwielkast 18 6 nylon moer M3

2 1 motor 3Vdc 19 18 moer M2

3 1 batterijhouder 20 18 schroef (2 x 8mm)

4 1 schuifschakelaar met draad 21 4 zelftappende schroef (2 x 4mm)

5 22 1 metalen as (2 x 40mm) 2 schroef (3 x 14mm)

6 23 1 metalen as (3 x 52mm) 2 schroef (3 x 18mm)

7 1 rondsel 8T 24 2 schroef (3 x 22m)

8 25 1 tandwiel 36T/10T (wit) 8 borgring (3.2 x 10.0 x 0.5mm)

9 1 tandwiel 40T/0T (wit) 26 15 borgring (2.6 x 6.0 x 0.5mm)

10 1 tandwiel 40T/10T (rood) 27 3 PVC buis (15mm)

Produkt Specifikationer

Mærke:	Velleman
Kategori:	Legetøj
Model:	KNS8

Har du brug for hjælp?

Hvis du har brug for hjælp til Velleman KNS8 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Legetøj Velleman Manualer

Velleman VMA500 Manual

4 December 2024

6 Oktober 2024

1 Oktober 2024

15 Februar 2023

8 December 2022

6 December 2022

Legetøj Manualer

Nyeste Legetøj Manualer

Playmobil Policía con Perro 70085 Manual

17 Juni 2025

Playmobil Action Heroes 9416 Manual

17 Juni 2025

Playmobil My Life 6499 Manual

17 Juni 2025

Playmobil My Life 9859 Manual

16 Juni 2025

Playmobil Action Heroes 9488 Manual

16 Juni 2025

Playmobil Country 6121 Manual

16 Juni 2025

Playmobil Country 6577 Manual

16 Juni 2025

Playmobil Calendario de Adviento "Operación de Rescate" 9486 Manual

15 Juni 2025

Playmobil Porsche 70067 Manual

15 Juni 2025

Playmobil Porsche Macan GTS 9376 Manual

15 Juni 2025