Velleman KNS5 Manual

Velleman Legetøj KNS5

Læs gratis den danske manual til Velleman KNS5 (7 sider) i kategorien Legetøj. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Velleman KNS5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

KNS5 VELLEMAN 1

KNS5 – AUTOMECH

1. Introduction & Characteristics

Thank you for buying the KNS5 ! Read this manual carefully before bringing the KNS5 into use.

• Familiarise yourself with the operation of transmissions steered through gears or pulleys.

• Easy to build, no glue or soldering required.

• Dislodge the pre-cut pieces when you need them and not before. Sand the jagged edges before use (sandpaper

included)

• The kit is powered by 2 AA-batteries (not included).

The kits of the KNS-series are supplied with prepunched boards, a gearbox, gears, shafts, a switch, a motor, a

battery holder and all necessary parts.

Note that the figures with the assembly instructions can be found in the second folder “KNS5 – Figures”!!!

2. Parts List

Part n° Quant. Description Part n° Quant. Description

1 motor holder

11 3 PVC tube (L=15mm)

2 1 battery holder 12 11 fixing plate (L-shaped)

1 motor with wire 13

4 nylon pad (Ø8mm)

4 14

1 slide switch with wire

1 belt (92 x 1mm)

5 15 2 metal shaft (2 x 60mm) 3 transmission belt # 16 (red)

6 16 2 metal shaft (2 x 70mm) 1 transmission belt # 18 (green)

3 roll (15 x 1.9mm, yellow) 17

4 nut M2

8 5 roll (19.5 x 1.9mm, yellow) 18 24 self-tapping screw (2 x 4mm)

9 8 nylon pad (6.6 x 4.8 x 2.1) 19 4 screw (2 x 8mm)

10 8 nylon pad (5.6 x 4.8 x 1.95) 20 4 washer

3. Prepunched Boards (see “KNS5 – Figures

”

)

4. Assembly (see also “KNS5 – Figures

”

)

Fig. 3 : Screw part n°12 to boards 4 & 5, then fix these boards to board 1.

Fig. 4 : Insert the motor (part n°3) in the motor holder (part n°1) and screw the battery holder (part n°2) to the back

of board 2. Screw the switch to the back of board 1. Refer to the wiring diagram (fig. 10) when connecting

the switch, the motor and the battery holder with each other.

Fig. 5 : Screw part n°12 to parts 2 & 3., then fix them to board n°1.

Fig. 7 : Use part n°12 to fix boards n°10 & 12 to board n°7, then use part n°12 to fix board n°11 to board n°6 (not

to board n°7).

Fig. 8 : Assemble all pulleys, shafts and wheels according to figure 8.

KNS5 VELLEMAN 2

Fig. 9 : Use the rubber bands to connect the different pulleys to make your Automech react like a real front wheel

drive, rear wheel drive or 4 wheels drive would (use belt n°14 for the latter). You can also change the

speed by adjusting the position of the rubber bands.

5. Troubleshooting

• Make sure the wiring is correct

• Note that all shafts (n°5, 6) in nylon pads (n°9, 10) should be able to move. This will allow the pulleys & wheels to

run smoothly.

KNS5 – AUTOMECH

1. Inleiding en Kenmerken

Dank u voor uw aankoop ! Lees deze handleiding aandachtig voor u de KNS5 in gebruik neemt.

• Leer hoe een tandwielaandrijving of een pulley met riemaandrijving werkt.

• Makkelijk te bouwen, zonder lijm of solderen.

• Maak de voorgesneden vormen pas los wanneer u ze nodig hebt. Schuur de scherpe randjes af voor gebruik

(schuurpapier meegeleverd)

• De kit wordt aangedreven door 2 AA-batterijen (niet inbegrepen).

De kits van de KNS-reeks worden geleverd met voorgesneden vormen, tandwielkast, koppeling, stangen,

schakelaar, motor, batterijhouder en alle vereiste onderdelen.

U vindt de figuren met de montagetips in de tweede folder : “KNS5 – Figuren”!!!

2. Lijst van onderdelen

Nr. Hoev. Beschrijving Nr. Hoev. Beschrijving

1 motorhouder

11 3 PVC buis (L=15mm)

2 1 batterijhouder 12 11 bevestigingsplaat (L-vormig)

3 1 motor met draad 13 4 nylon kraagring (Ø8mm)

4 1 glijschakelaar met draad 14 1 riem (92 x 1mm)

5 15 2 metalen as (2 x 60mm) 3 aandrijfriem # 16 (rood)

6 16 2 metalen as (2 x 70mm) 1 aandrijfriem # 18 (groen)

3 katrol (15 x 1.9mm, geel) 17

4 moer M2

8 5 katrol (19.5 x 1.9mm, geel) 18 24 zelftappende schroef (2 x 4mm)

9 8 nylon kraagring (6.6 x 4.8 x 2.1) 19 4 schroef (2 x 8mm)

10 8 nylon kraagring (5.6 x 4.8 x 1.95) 20 4 borgring

3. Voorgesneden vormen (zie “KNS5 – Figuren”)

Produkt Specifikationer

Mærke:	Velleman
Kategori:	Legetøj
Model:	KNS5
Bredde:	240 mm
Dybde:	85 mm
Højde:	95 mm
Produkttype:	Ingeniørsæt
Batterier inkluderet:	Ingen
Antal understøttede batterier:	2
Tema:	Ingeniørarbejde