Velleman VTTEST11 Manual

Velleman Kabler til computere og periferiudstyr VTTEST11

Læs gratis den danske manual til Velleman VTTEST11 (11 sider) i kategorien Kabler til computere og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Velleman VTTEST11, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/11

VTTEST11 1 VELLEMAN

VTTEST11 – CABLE DETECTOR / TESTER

1. Introduction & Features

Thank you for buying the VTTEST11! Please read the manual thoroughly before bringing this device into service.

If the device was damaged in transit, do not use it and contact your dealer.

The allows you to test and detect wiring and determine RJ12 connector polarity. VTTEST11

2. Contents

a. Tone Generator (A)

1. Test wires (2)

2. Test RJ12 plug

3. Mode switch

4. Low voltage indicator LED

5. Signal indicator LED

6. Audio signal switch

b. Cable Tracer Probe (B)

7. Test tip

8. Signal indicator LED

9. Low voltage indicator LED

10. Trace button

11. Volume control (on the side)

12. Mode switch (on the side)

13. Loudspeaker (at the back)

3. Technical Specifications

a. Tone Generator

Operating voltage 9Vdc ±15%

Operating current 10mA (tone) ; 20mA (cont)

Size (LxWxH) 115 x 62 x 27mm

Weight ± 130g

Square wave output ± 10Vpp

1. Single audio frequency ± 900Hz

2. Dual audio frequency ± 900-1000Hz

b. Cable Tracer Probe

Operating voltage 9Vdc ±15%

Operating current 25mA (L)

80mA (SP @ max. volume)

100mA (S&L @ max. volume)

Size (LxWxH) 205 x 40 x 38mm

Weight ± 80g

Max. reception sensitivity >30mV

Max. output volume ± 120dB

VTTEST11 2 VELLEMAN

4. Use

a. RJ12 Network / Phone Connector Test

The Tone Generator can be used to determine the polarity of a phone line or network connection.

1. Set the tone generator's mode switch (p.1 #3) to 'Off'.

2. Insert the phone line connector in the phone / network socket and connect the red and black connectors to the

wires to be connected.

3. Upon connection of the red and black connectors, the signal indicator LED (p.1 #5) should light up. Green means

the polarity is correct (black is "+" and red is "-"). Red means the polarity is inversed (black is "-" and red is "+").

If the LED does not light up, either the connections are not established correctly or the socket is not connected.

If the LED flashes green and red alternately, it means there is an incoming phone call (ring signal).

b. Cable test

The Tone Generator can be used to determine whether or not a cable is interrupted (test per wire couple).

1. Set the tone generator's mode switch (p.1 #3) to 'Cont'.

2. Create a short circuit between the wires to be tested at the far end of the cable.

3. Connect the red and black connectors to the wires to be tested.

4. If the signal indicator LED (p.1 #5) lights up (green), the 2 tested wires are uninterrupted. If the LED does not light

up, either one or both of the wires are broken or the wrong wires were connected or short circuited.

Beware: make sure the wire couple under test is not in contact with any other electrified or earthed object ; this may

cause an incorrect test result.

c. Cable detection / test

Use both the tone generator and the cable tracer to verify where a cable is going, if it is uninterrupted or not and

where the interruption is located if it is indeed interrupted

1. Set the tone generator's mode switch (p.1 #3) to 'Tone'. Select the tone you want to hear (single or dual tone) with

the audio signal switch (p.1 #6).

2. At one end of the cable / wires to be tested, connect the red clip to any wire or one specific wire you want to test.

Connect the black clip to the ground wire or, when you cannot find it, one of the other wires. The signal indicator

LED (p.1 #5) should be red. When it is not lit, the test wire is making contact with either ground or the wire the

black clip is attached to.

3. Set the mode switch on the side of the probe (p.1 #12) to the desired signal:

"L.": lamp signal only: the signal LED lights up when the probe captures the signal.

"SP.": speaker only: a (single or dual) tone becomes audible when the probe captures the signal

"S&L": lamp + speaker: the LED lights up & a tone becomes audible when the probe captures the signal.

The sound volume is controllable with the volume control (p.1 #11).

If you do not know where the cable is going or if there are several similar cables, you can detect the correct one

with the probe. If you do know where the cable is going, the probe allows you to verify immediately at the other

end whether or not the cable is interrupted. If no signal is obtained at the other end of the cable, the test wire is

probably interrupted. Follow the cable while keeping the "Trace" button (p.1 #10) pressed to where the signal

stops ; the signal wire is interrupted at that point.

Remarks:

• The best test results are obtained when the black clip is connected to a separate ground wire.

• The probe is very sensitive: as it gets nearer the signal wire, the tone gets louder or illumination gets brighter.

• Electric fields may interfere with the detection of the signal wire.

• Always pay attention to the low battery indicators (p.1 # 4 & 9): when they light up, replace the battery of the

corresponding device promptly. A low battery may cause a signal or detection to be too weak to be noticed.

The information in this manual is subject to change without prior notice.

Produkt Specifikationer

Mærke:	Velleman
Kategori:	Kabler til computere og periferiudstyr
Model:	VTTEST11
Produktfarve:	Hvid
Dimensioner (BxDxH):	205 x 40 x 38 mm
Driftsspænding:	9 V
Understøttede stik:	RJ-11