PAC CAM-GM51 Manual

PAC Ikke kategoriseret CAM-GM51

Læs gratis den danske manual til PAC CAM-GM51 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om PAC CAM-GM51, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Reverse Camera Retention Harness

for Select 2014 - 2017 General Motors Vehicles

CAM-GM51

PAC-audio.com

Page 1

Rev: V1

Date: 042718

The CAM-GM51 is a plug and play reverse camera retention harness that gives the ability to retain the factory camera when

replacing the factory radio.

Introduction and Features

Installation Steps

1. Verify that the system has an IO4, IO5 or IO6 RPO code. If so then locate the HMICM in the vehicle. This will normally be

found behind the glove box in trucks and SUVs, or high in the passenger kick panel in cars.

2. Disconnect the Gray 12-pin connector from the HMICM and connect it to the CAM-GM51

3. Route the Yellow RCA labeled “Camera” up and into the radio cavity in the dash, and connect it to the camera input on

the back of the aftermarket radio.

Illustration / Schematic

Installation Notes

1. The CAM-GM51 harness works on vehicles with the IO4, IO5 and IO6 RPO coded factory audio systems. The RPO codes

can normally be found by looking at the sticker in the glove box or in the trunk under the spare tire cover panel. On 2018+

vehicles it may be necessary to scan a QR code with your phone or tablet to view the vehicles RPO codes.

2. The CAM-GM51 harness connects at the Human Machine Interface Control Module (HMICM) not at the radio. The HMICM

is normally found either behind the glove box in trucks and SUVs, or high in the passenger side kick panel area. The

HMICM will have the USB and LVDS cables connected to it. The HMICM will look like the pictures below.

3. The factory reverse camera is powered by the vehicle and not the HMICM. The camera will continue to be powered even

when disconnected from the HMICM, so no additional wiring is required to supply the camera with power.

CAMERA

CAM-GM51

Connect to

HMICM

Connect to

Aftermarket Radio

Produkt Specifikationer

Mærke:	PAC
Kategori:	Ikke kategoriseret
Model:	CAM-GM51

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC CAM-GM51 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret PAC Manualer

PAC CAM-GM51 Manual

11 Juli 2025

PAC TY1A-RS Manual

11 Juli 2025

PAC SR-F15009HX Manual

10 Juli 2025

PAC SRK-RAM13HX Manual

10 Juli 2025

PAC AAI-TY3 Manual

30 Juni 2025

PAC SRK-GM14HX Manual

10 Marts 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

19 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ResMed AirCurve 10 CS PaceWave Manual

18 Oktober 2025

Sungrow SH10RT-V113 Manual

18 Oktober 2025

AstralPool Niche Switch Manual

18 Oktober 2025

Sungrow SH8.0RT-V113 Manual

18 Oktober 2025

AstralPool Roma Manual

18 Oktober 2025

Evenflo SafeMax Manual

18 Oktober 2025

NEO Tools 94-002 Manual

18 Oktober 2025

LC-Power Platinum Pro LC1000P V3.1 Manual

17 Oktober 2025

Metz 130B21-E Manual

17 Oktober 2025

NEO Tools 99-038 Manual

17 Oktober 2025