• This HD video monitor is intended as an aid. It is not a substitute for proper adult supervision, and should
not be used as such.
Testing the sound level of the HD video monitor
• For hearing protection, make sure the parent unit is more than 3 metres away from the baby
unit. If you hear any high-pitched noise from the parent unit, move the parent unit further
until the noise stops. You can also press - VOL on the parent unit to lower or mute the noise.
• Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit.
Positioning the monitorHD video
• Keep the baby unit out of the reach of your baby. Never place
or mount the baby unit inside the baby’s cot or playpen.
1. Place the baby unit more than 1 metre away from your
baby.
2. Adjust the angle of the baby unit to aim at your baby. Refer
to the online help on how to use the Pan/tilt and Zoom
functions of the baby unit.
3. To avoid causing high-pitched screeching noise from your HD video monitor:
• Make sure your baby unit and parent unit are more than 3 metres apart; OR
• Turn down the volume of your parent unit.
>
10ft (3m)
> 3ft (1m)
If you plan to install your baby unit in a designated
location, and use your home Wi-Fi network to
connect your video monitor, you need to test
which of your selected monitoring areas within the
house have good Wi-Fi signal strength. After you
have powered on your parent unit, you can use
your parent unit’s Wi-Fi signal strength indicator
to assist in checking. Once you have identified the
suitable location, you can install your baby unit.
Adjust the distance between your baby unit and
the Wi-Fi router if needed.
• Depending on surroundings and obstructing
factors, such as the effect distance and internal
walls have on signal strength, you may experience
reduced Wi-Fi signal. To improve the Wi-Fi signal
strength, adjust the distance or direction of your
parent unit. Check with your parent unit again.
1. Place the wall mount bracket on a wall and then use
a pencil to mark the top and the bottom holes as
shown. Remove the wall mount bracket and drill
two holes in the wall
(7/32 inch drill bit).
Notes
• Check for reception strength and baby unit’s angle before drilling the holes.
• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units.
2. If you drill the holes into a stud, go to step 3.
• If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the
wall anchors are flush with the wall.
3. Align the wall mount bracket and screws with the
holes in the wall as shown. Tighten the screw in the
middle hole first, so that the wall mount bracket
position is fixed. You can tighten the other screw in
the top hole.
3. Insert the screws into the holes and tighten the screws until only 1/4 inch
of the screws are exposed.
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket
at the bottom to secure the baby unit. Align
the holes on the wall mount bracket with the
screws on the wall, and slide the wall mount
bracket down until it locks into place.
5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and
secure the angle.
OR
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket at the
bottom to secure the baby unit.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
If you require assistance in operating this product, please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com.
Voluntary Product Enquiry
In addition to your Statutory Rights and subject to the conditions below, VTech warrants that this product will be
free from any defect in materials or workmanship under conditions of normal use for a period of 24 months from
date of purchase.
VTech does not warrant that the product will be free from defects if defects are caused by an accident, misuse,
abuse, improper installation or operation, vermin infestations, lack of reasonable care, unauthorised modification,
loss of parts, tampering or attempted repair by a person not authorised by VTech; or where the product has been
damaged by lightning or a mains power surge.To make a claim under this Voluntary Product Warranty you must
call the TecHelp Information Line on 1300 369 193 or contact VTech by e-mail at: tcpsupport_au@vtech.com where
a Customer Service Representative will inform you of the product return process. You will need to ensure that:
• You provide proof of purchase;
• Your product is suitably packaged (original packaging is not required); and
• You have included all components from the original purchase.
For your records
Date of purchase:
Place of purchase:
Serial number:
For Voluntary Product Warranty purposes, proof of purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product Warranty are in addition to other rights and remedies that are
available to you under law, which cannot be excluded. The processes for this Voluntary Product Warranty in no way
limit your rights which arise as a result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN 70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT RETURN OR SERVICE ADDRESS – PLEASE CONTACT TECHELP BY
PHONE OR EMAIL FOR PRODUCT AND WARRANTY SUPPORT. NO LIABILITY WILL BE ACCEPTED BY VTECH FOR
PRODUCTS RETURNED TO THIS ADDRESS UNDER THIS VOLUNTARY PRODUCT WARRANTY.
Phone number: 1300 369 193
Email address: tcpsupport_au@vtech.com
Statutory Rights
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Customer service and product warranty
The crossed-out wheelie bin symbols on products and batteries, or on their respective
packaging, indicates they must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more
than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and product
The applied nameplate is located at the bottom of the baby unit’s base.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above 2 metres.
4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or
caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will
continue working properly for any given period of time. Further, this is not a medical device and should not
be used as such. This product is intended to assist you in supervising your baby.
5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is
used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low
air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot
oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery
in an extremely high temperature surrounding environment can result in an explosion or the leakage of
flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the
leakage of flammable liquid or gas. Dispose of used battery according to the instructions.
7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage
the product.
Power adapter information:
Output: 5V DC 1A.
Tenpao International Ltd.
Model : S005BNS0500100
Rechargeable battery information:
Lithium-ion Polymer 2100mAh 3.8V
TMB - BP1803/I9300
8. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are
not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet (power adapter) shall be installed near the equipment and shall
be easily accessible.
10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be
walked on or crimped.
13. This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply in your home, consult your dealer or local power company.
14. The equipment is to be supplied from an identified USB port complying with the requirements of Limited
Power Source.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for ventilation. To protect them from overheating, these
openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This
product should never be placed near or over a radiator or heat register.
18. Never push objects of any kind into this product through the slots because they may touch dangerous
voltage points or create a short circuit. Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service
facility. Opening or removing parts of the product other than specified access doors may expose you to
dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is
subsequently used.
20. You should test the sound reception every time you turn on the units or move one of the components.
21. Periodically examine all components
for damage.
22. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the product has never been used before purchase,
reset the baby monitor periodically by powering off and then powering on the units, and power off the
baby monitor if you will not use it for some time.
23. Children should be supervised to ensure that they do not play with the product.
24. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach
of children.
25. The product is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
• Use and store the product at a temperature between 0oC and 40oC.
• Burn hazard, fire hazard, explosion hazard associated with mishandling of the battery.
• Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a
heating source.
• Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out
of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag.
• Never place the baby unit(s) inside the baby’s cot or playpen. Never cover the baby unit(s) or
parent unit with anything such as a towel or a blanket.
• Other electronic products may cause interference with your baby unit. Try installing your baby unit as far
away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms,
room monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of
the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S.
Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned
ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless
devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly
and according to the instructions in this user’s manual, the product is safe to be used based on scientific
evidence available today.
Important safety instructions
>10ft (3m)
<10ft (3m)
