Walrus Audio Slötvå Manual

Walrus Audio Ikke kategoriseret Slötvå

Læs gratis den danske manual til Walrus Audio Slötvå (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Walrus Audio Slötvå, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
9 volt DC, Center Neg.
100ma min*
Output Jack
Bypass LED
Bypass Switch/
Secondary Function
Sustain Switch
Input Jack
*The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Depth knob Secondary
Function:
Modulation Rate
Mode Switch Secondary
Function:
Wave shape selection
The Slötvå Multi Texture Reverb allows players to create and save up to three
presets with lush, modulated, sleepy and ambient soundscapes. Stocked
with three different algorithms specifically designed to invoke textures for
bringing dreams from your subconscious to reality.
The toggle switch allows three different reverb modes, Dark (Lower Octave),
Rise (Ambient Swell) and Dream (Latching Pad), while secondary functions
on the switch change between different wave shapes for the modulation on
the reverb trail.
Combine deep modulation with long washy trails and experience, the Slötvå.
Got questions or need a repair? help@walrusaudio.com. All our pedals come with a limited lifetime warranty.
CONTROLS:
DECAY – Adjusts the length of the reverb decay. Go from tight short reverb,
at full counter-clockwise, to long drawn out texture at full clockwise.
FILTER – Controls the tone of the reverb decay. Each algorithm includes
a low-pass filter optimized for that unique sound and the knob controls
the filter cutoff frequency. Turn the knob up to open the filter for brighter
tones, and down to close the filter resulting in a darker tone.
MIX – Turn counter-clockwise for increased dry signal, and clockwise for
more reverb. Use the white line to reference approximately equal parts dry
and reverb. Since this point is around 2 o’clock, it gives a greater range of
adjustment of your mix ratio below the 50/50 point making it easier to dial
in the perfect amount of reverb.
X – The X knob changes jobs depending on which algorithm is selected.
DARK – Sets the level of a -1 octave signal that feeds the reverb.
RISE – Sets the amount of time it takes the reverb to swell in
after a note is played. Set lower for shorter rise times and higher
for longer rise times.
– Sets the depth of vibrato applied to the reverb decay. DREAM
DEPTH – Controls the amount of modulation applied to the reverb decay. Go from no modulation, to
nightmare inducing pitch bending at high settings.
Secondary Function: Rate - Controls the speed of the modulation applied to the reverb decay.
ALGORITHM SWITCH – The toggle switch selects one of three onboard reverb algorithms.
Secondary Function: Wave Shape selection.
REVERB MODES: Use the toggle switch to select one of three onboard algorithms.
DARK – Add a lower octave to your reverb trail. Create deep and wide atmospheric sounds and channel
nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.
RISE – Auto-swell reverb for beautiful cinematic swells. Don’t rush it. Let it breathe and gently wake up. X
knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise
times and higher for longer rise times. Note: Rise works best in front of an amp, not through an FX loop.
DREAM – Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment
with the X knob to add vibrato over the pad. Press sustain again and pad will decrescendo according to
where decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.
MODULATION WAVE SHAPES:
SINE – Smooth and even pitch up and down modulation.
WARP – Asymmetric pitch up modulation similar to a warped record.
SINK – Asymmetric pitch down modulation for sinking detune similar to a Bigsby.
BYPASS – Turns the effect on and off. It also features our smart bypass switching. When the switch is in off
position, press and hold to temporarily activate the effect to add a moment of reverb texture. Releasing
the switch turns the effect off, and fades it out.
SUSTAIN – When pressed, the decay switch ramps up the reverb trail to maximum creating long dreamy
reverb trail and then ramps back down to the decay knob setting when released. In the “Dream” algorithm,
the sustain switch is latching. Press it once to capture and sustain the current reverb decay for extremely
long pad-like sounds. Press it again to let the reverb trail taper off, based on the position of the decay knob.
SECONDARY FUNCTIONS – To access the secondary functions, with the pedal engaged, hold down the
bypass switch and use the toggle to select the desired wave shape, and the depth knob to set the desired
rate. The bypass LED will flash at the rate of modulation while in the secondary mode. The pedal remembers
the wave shape and rate settings for the current preset when saved, until the next time they are modified.
The pedal also maintains the algorithm and depth setting when modifying secondary functions.
WALRUSAUDIO.COM
TRAILS MODE – The Slötvå can run in trails or no trails mode. In trails mode, when you turn the pedal off,
the reverb decay dies off naturally. In no trails mode, the decay is abruptly cut off when you turn the pedal
off. To toggle between either mode, hold down the bypass switch for 1 second while applying power to
the pedal. Unplug power and repeat to toggle to the other mode. Default is Trails mode.
Presets - Slötvå has 3 on-board presets (Red, Green, Blue). If the same algorithm is used in the next preset,
the reverb sound will fade into the saved settings.
Scroll through the presets by pressing both stomp switches at the same time. Each press of both stomp
switches will load the next preset until you get back to red and the pattern of Red, Green, Blue repeats.
To save a preset:
1. Scroll to the preset color you want to save a new sound.
2. Using the knobs and switches, dial in the desired reverb sound. The preset LED will turn purple
indicating the preset has been modified. The preset LED will go back to the preset color when you cross
the current saved setting.
3. To save, hold down the Bypass and Sustain switches until the preset LED blinks. The preset is now
saved and the LED will return to the preset color.
FACTORY RESET To perform a factory reset, hold down both foot switches while plugging in power to –
the pedal. Hold both switches until the Preset LED starts to flash, then release both switches. The pedal
will now be in Trails mode with the three default presets loaded in the Red, Green and Blue presets.
The default wave shape are as follows: Dark - Sink // Rise - Sine // Dream - Sink.

Produkt Specifikationer

Mærke: Walrus Audio
Kategori: Ikke kategoriseret
Model: Slötvå

Har du brug for hjælp?

Hvis du har brug for hjælp til Walrus Audio Slötvå stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Walrus Audio Manualer

Walrus Audio

Walrus Audio Silt Manual

28 Juli 2025
Walrus Audio

Walrus Audio 385 MKII Manual

27 Juli 2025
Walrus Audio

Walrus Audio Qi Etherealizer Manual

16 Juli 2025
Walrus Audio

Walrus Audio Iron Horse Manual

18 Juni 2025
Walrus Audio

Walrus Audio Janus Manual

17 Juni 2025
Walrus Audio

Walrus Audio Ages Manual

7 Juni 2025
Walrus Audio

Walrus Audio Jupiter V2 Manual

6 Juni 2025
Walrus Audio

Walrus Audio Fundamental Delay Manual

31 Maj 2025
Walrus Audio

Walrus Audio Slötvå Manual

14 Januar 2025
Walrus Audio

Walrus Audio Kangra Manual

7 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MiVue 540 Manual

2 August 2025
Pro User

Pro User PSI2000TX Manual

2 August 2025
Guede

Guede 5T Manual

2 August 2025
Navman

Navman EZY40 Manual

2 August 2025
Thule

Thule Chariot Ski kit Manual

2 August 2025
Hozelock

Hozelock 5102 Manual

2 August 2025
ART

ART 310 Manual

2 August 2025
Gorenje

Gorenje KAS53ZDCINVFT Manual

2 August 2025
Gorenje

Gorenje KAS35ZDCINVFT Manual

2 August 2025
Navman

Navman MY450LMT Manual

2 August 2025