Walrus Audio Silt Manual

Walrus Audio Ikke kategoriseret Silt

Læs gratis den danske manual til Walrus Audio Silt (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Walrus Audio Silt, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

The Walrus Audio Silt Harmonic Fuzz is a collaborative

project with tube expert Jim Hagerman of Hagerman

Ampliﬁcation. Wielding an internal pre-amp tube,

the Silt is a two-in-one fuzz that creates massively

rich fuzz tones perfect for chords and rhythmic parts

or with the press of a switch, adds uniquely harmonic

overtones to the signal before hitting the tube. Crafted

speciﬁcally for those seeking a harmonically rich fuzz

experience, the Silt boasts an analog circuit with the

distinctive warmth of a 12AU7 tube as its drive section,

letting you explore

pOWER InFO

CoNTROLS

9V - 12V DC, Center Neg. 300mA min.*

Tip: Running the pedal at 12v will give you an extra gain boost,

you push the primal boundaries of fuzz to deliver the searing t

you’ve been searching for.

Silt plays well with other pedals and does not need to be place

in your chain like some vintage pedals.

*The use of an isolated power supply is recommended for pow

all Walrus Audio Pedals. Daisy chain power supplies are not

recommended.

CONTOUR

Toggle between highpass (up), flat (middle),

and lowpass (down) curves in the pre-tube

EQ stage, like uncovering layers of sonic

strata. Especially helpful when switching

between different styles of pickups.

HARMONIC SWITCH

Harmonic Mode activates a f requency

doubler before the drive section of the

pedal. This produces crispy, octave-like

sounds, lending a unique edge to your

lead tones. Try this with your guitar tone

knob rolled off.

Should the tube in your Silt ever fail, follow these steps to replace it.

We recommend using a JJ 12AU7 (ECC82) tube.

1. Take out the four screws

to remove the backplate.

2. Grab both ends of the

tube’s PCB and gently pull

straight up.

3. Gently pull the tube out

of the socket.

4. Put the new tube into

the tube socket making

sure all pins are aligned.

5. Connect the tube PCB

back to the Silt’s main PCB

ensuring that all 10 pins

are lined up. (8 pins on the

longer side, 2 pins on the

shorter side.)

TUBE MAINTENANCE

10 PIN

CONNECTOR

2 PIN

CONNECTOR

Produkt Specifikationer

Mærke:	Walrus Audio
Kategori:	Ikke kategoriseret
Model:	Silt

Har du brug for hjælp?

Hvis du har brug for hjælp til Walrus Audio Silt stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Walrus Audio Manualer

Walrus Audio Luminary Manual

16 August 2025

Walrus Audio Canvas Nano Manual

14 August 2025

Walrus Audio Canvas Rehearsal Manual

13 August 2025

Walrus Audio Canvas Clock Manual

12 August 2025

Walrus Audio Canvas Re-Amp Manual

12 August 2025

Walrus Audio Canvas Power HP Manual

12 August 2025

Walrus Audio Silt Manual

28 Juli 2025

Walrus Audio 385 MKII Manual

27 Juli 2025

Walrus Audio Qi Etherealizer Manual

16 Juli 2025

Walrus Audio Iron Horse Manual

18 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM SU9030 Manual

13 September 2025

IFM O2U554 Manual

13 September 2025

Speco Technologies HTi70TM Manual

13 September 2025

QSC RMXa Manual

13 September 2025

Tineco Floor One S2 Series Manual

13 September 2025

Tineco Floor One S3 Breeze Manual

13 September 2025

Tineco Floor One S5 Steam Manual

13 September 2025

Osram VX500-CB Manual

13 September 2025

Zelmer ZTS7990 Manual

13 September 2025

Osram VX250-SP Manual

13 September 2025