Whale Supersub Manual

Whale Ikke kategoriseret Supersub

Læs gratis den danske manual til Whale Supersub (40 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Whale Supersub, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/40

Model Number SS5012 (B) Supersub 500 (12V d.c.)

Model Number SS5022 (B) Supersub 650 (12V d.c.) with N.R.V.

Model Number SS1012 (B) Supersub 1100 (12V d.c.) with N.R.V.

Model Number SS1024 (B) Supersub 1100 (24V d.c.) with N.R.V.

Installation Guidelines for:

This booklet must be read prior to installation

Model Number SS5212 (B) Supersub Smart 650 (12V d.c.) with N.R.V.

Model Number SS1212 (B) Supersub Smart 1100 (12V d.c.) with N.R.V.

Model Number SS1224 (B) Supersub Smart 1100 (24V d.c.) with N.R.V.

Standard Pumps (separate bilge switch required)

Automatic Pumps

Supersub

Range

Model shown: SS5212

Mounting wedge is supplied with automatic pumps only.

* B Suffix refers to bulk packed versions

N.R.V. = Non Return Valve

The original low profile narrow electric bilge pump.

Please Note: Pump operates with a 5 second on delay on automatic setting

Supersub

Range

Munster Simms Engineering Ltd, 2 Enterprise Road, Bangor, Co Down, N. Ireland BT19 7TA

Tel: +44 (0)28 9127 0531 Web: www.whalepumps.com Email info@whalepumps.com

Thank you for purchasing this Whale product.

For over 60 years Whale has led the way in the design and manufacture of freshwater, bilge and waste management systems including plumbing,

taps, showers and pumps, for low voltage applications. The company and its products have built a reputation for quality, reliability and innovation

backed up by excellent customer service. For information on our full product range visit: www.whalepumps.com

CONTENTS LIST OF IMAGES

To the fitter

Read the following carefully before installation. Check that the product is suitable for the intended application, follow these installation instructions

and ensure all relevant personnel read the points below. Also ensure that these operating instructions are passed on to the end user.

WARNING: Please note that incorrect installation may invalidate warranty.

To the user

Read the following instructions carefully.

All Supersub models are uniquely designed, specifically for fast and efficient removal of bilge water from leisure craft. The Supersub range fits into

narrow and low spaces that other bilge pumps cannot reach. SS5012, SS5022, SS1012 AND SS1024 ARE NOT AUTOMATIC PUMPS. (Please

refer to Section 4 for the switches and optional extras that can be used with these products).

Supersub Smart 650 and 1100 are automatic. The pump will sense the presence of water and will switch on, then will turn off again when the

water level has dropped. The switching is solid state hence there are no moving parts. The Supersub Smart models allow waves of water to pass

over, without turning the pump on every time, as it has a built in time delay.

• The Supersub and Supersub Smart range of products are designed to pump normal bilge water. Output capacity depends on installation and

operating conditions. If this product is intended to be used for any other purpose or with any other liquid, it is the user's responsibility to ensure

that the pump is suitable for the application and, in particular, that the materials are fully compatible with the liquids to be used.

• This product must only be used in the bilges of leisure craft. If this product is to be used as the sole and/or primary bilge pump, the

Supersub 500/650/1100 and Supersub Smart 650/1100 pumps must only be used in boats up to 24m (78.8 ft).

• The bilge water only be evacuated through a correctly installed skin fitting above the water line of the boat.must

• With all applications, it is important that a system of safe working practice is applied to installation, use and maintenance. Ensure the electric

supply is turned off and waste water system is drained before installation.

• The Supersub range is designed only for the removal of normal bilge water in leisure boats and personal watercraft (as explained in

Section 2 - Application). Your warranty may be invalidated if the product is used in other applications or outside the remit of the standards

quoted on the packaging and pump body.

• Bilge pump capacities may not be sufficient to prevent flooding from rapid accumulation of water due to storms, rough weather and/ or NOTE:

rapid leaks created by hull damage and or unsafe navigational conditions.

• The pumped water must be evacuated through a skin fitting above the water line (see typical installation diagrams). The Supersub and

Supersub Smart range is not for use in systems evacuating water through a skin fitting or seacock below the water line. All pipework must

contain a correctly installed anti-syphon valve / loop.

• In order to securely fasten the unit, ensure that the mounting surface is a minimum thickness of 19mm (3/4") (screws supplied with retail models

only). screw directly to the hull - mounted on a bulkhead or on an additional board.NOTE Do not must be

• unscrew the rear section, as interference with the internal electrics will render the pump unfit for use. - this is a NOTE - DO NOT

non-serviceable part of the pump.

•WARNING: Fire hazard. Wiring must comply with applicable electrical standards and include a properly rated fuse or circuit breaker. Improper

wiring can cause a fire resulting in injury or death. Switch off the power while making connections.

LV1219 Non-Return Valve (recommended for SS5012 models) .

BE9003 / BE9006 Automatic, water activated, electronic switch (For use with SS5012, SS5022, SS1012 and SS1024 models).

BE9002 Automatic, water activated, floatswitch (Please see Figure 5, Supersub Automatic System).

SF5131 3/4” Skin fitting (for use with SS5012, SS5022 and SS5212 models)

SF5204 1” Skin Fitting (for use with SS1012, SS1024, SS1212 and SS1224 models)

See diagrams (page 4)

1. Principles of Operation 6. Instructions for use

2. Application 7. Trouble shooting

3. Warning 8. Winterization

4. Optional Extras 9. Service Support & Warranty

5. Installation Instructions 10. Declaration of conformity, standards, approvals

Figure 1. Installation & Recommendations

Figure 2. Fitting Instructions

Figure 3. Fitting Instructions - Into Existing Drill Holes

Figure 4. Typical Installations

Figure 5. Wiring Diagrams

Figure 6. Plumbing

Figure 7. Maintenance

1. Principles of Operation

2. Application

3. Warning

4. Optional Extras

5. Installation Instructions

Produkt Specifikationer

Mærke:	Whale
Kategori:	Ikke kategoriseret
Model:	Supersub

Har du brug for hjælp?

Hvis du har brug for hjælp til Whale Supersub stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Whale Manualer

Whale Gusher 30 Manual

5 September 2024

Whale UF2214 Manual

5 September 2024

Whale Gusher 10 Mk3 Manual

5 September 2024

Whale InstantMatch Premium SDP303T Manual

5 September 2024

Whale Switch Connect BP1578 Manual

5 September 2024

Whale Instant Match SDP134Tn Manual

20 Juli 2024

Whale Orca 3000 Manual

19 Juli 2024

Whale Smartbail Manual

7 Juli 2024

Whale Gulper 320 Manual

7 Juli 2024

Whale Supersub Manual

7 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Essentiel B SP40 Manual

18 Juni 2025

Royal Catering RCGW 1 Manual

18 Juni 2025

Tracer GameZone Hexy2 Manual

18 Juni 2025

Chapin 97084 Manual

18 Juni 2025

Royal Catering RCSW-3R Manual

18 Juni 2025

Festo EMMB-AS-60-02-K-S30M Manual

18 Juni 2025

Royal Catering RC-FST635G Manual

18 Juni 2025

Smeg KBSF02WH Manual

18 Juni 2025

Steinberg SBS-FZ 1000/6M Manual

18 Juni 2025

Royal Catering RCGW-2 Manual

18 Juni 2025