Xaoc Samara Manual


Læs gratis den danske manual til Xaoc Samara (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Xaoc Samara, eller vil du spørge andre brugere om produktet?

Side 1/6
utility
waveform
processor
Model of 1962
operator’s manual rev. 1962/1.0
Thank you for purchasing this Xaoc Devices prod-
uct. Samara is a "Swiss Army Knife" type of mod-
ule, intended to serve the most common voltage
and audio signal processing purposes such as at-
tenuation, offsetting, mixing, inverting, and even
basic waveshaping. We have designed it to com-
plement the ever-popular Batumi module but it
will happily serve all these functions on its own.
The module requires 10hp worth of free space
in the eurorack cabinet. The ribbon type power
cable must be plugged into the bus board, pay-
ing close attention to polarity orientation. The
red stripe indicates the negative 12V rail and is
supposed to point in the same direction on both
the bus board and the unit. The module itself is
secured against reversed power connection,
however reversing the 16-pin header may cause
serious damage to other components of your
system, because it will short-circuit the +12V
and +5V power rails. The module should be fas-
tened by mounting the supplied screws before
powering up. To better understand the device,
we strongly advise the user to read through the
entire manual before using the module.
Samara features four channels—each with two
inputs and an attenuator, additional switchable
offset generators, four voltage level and polarity
indicators, two adders with switchable scale,
and a precision four-channel processor that se-
lects minimum and maximum voltage. See the

    
are four identical channels. Each channel features
a regular input in as well as an inverting inv
input . The difference between these inputs is
adjusted by an active attenuator. Each unused in-
put is normalized to 0V, hence this arrangement
allows for two independent channels of normal
attenuation, or inverting attenuation, or comput-
ing a difference between two voltages or signals.
Additionally, two sources of a stable +5V
voltage are switchable in channels and 1 3,
activated by pressing the corresponding illu-
minated button . This offset is added to the
inputs before attenuation. Thus, if nothing is
patched to the inputs of channels and/or 1
3, they can be used as a source of constant
voltage, from 0 to 5V. The resulting signal or
voltage, after being manually attenuated by
the level/ofst knob , is available on the
corresponding out outputs .
To achieve independent control over scale and
offset two channels must be utilized: one for
offset (with the engaged 5V offset toggle
and nothing patched into the inputs) and an-
other one for scaling.
A bi-color LED indicates the value and polar-
ity of the voltage through corresponding bright-
ness and color. For audio signals, fast blinking of
red and green yields a yellow-orange mixture
with intensity corresponding to signal level.
Note that you may use the individual outputs
to re-direct the processed channels to other
channels. For example, an attenuated signal or
module
explained


Produkt Specifikationer

Mærke: Xaoc
Kategori: Ikke kategoriseret
Model: Samara

Har du brug for hjælp?

Hvis du har brug for hjælp til Xaoc Samara stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Xaoc Manualer

Xaoc

Xaoc Lublin 1957 Manual

2 Februar 2025
Xaoc

Xaoc Bytom 1981 Manual

8 Januar 2025
Xaoc

Xaoc Ustka 1966 Manual

6 September 2024
Xaoc

Xaoc DEVA Manual

4 Juli 2024
Xaoc

Xaoc Katowice Manual

4 Juli 2024
Xaoc

Xaoc Tirana Manual

4 Juli 2024
Xaoc

Xaoc Sarajewo Manual

4 Juli 2024
Xaoc

Xaoc Batumi Manual

4 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer