Accell UltraAV K072C-013B Manual

Accell Modtager UltraAV K072C-013B

Læs gratis den danske manual til Accell UltraAV K072C-013B (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Accell UltraAV K072C-013B, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI Distribution
Amplifi er. This product is designed to provide an exceptional
performance and value. Please review the manual before
operating and retain for future reference.
- CAUTION -
1. Ensure the unit has suffi cient
ventilation. Do not cover
ventilation openings. Do not install
in a confi ned space.
2. Do not operate near source
of heat. Do not stack on to p,
underneath or between other heat
generating unit/s including other
amplifi ers.
3. Unplug power adapter if not
used for an extended period.
4. To prevent damage from power
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the fi eld. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV 4x4 HDMI Matrix and Distribution Amplifier accepts signals
from up to 4 HDMI enabled audio/video sources and distributes the
signal to up to 4 HDMI enabled displays. The matrix can be configured to
send any input to a HDMI displays, monitors, projectors or TV’s.ny
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both oltage over-current and over-v
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the excessive current or voltage
has passed.
Package Contents
●HDMI Distribution Amplifier (Matrix) ●Power Adapter
●Remote Control (with battery) ●Owner’s Manual
●CD-ROM (for RS-232 control)
Model Number:
K072C-013B
UltraAV
®
HDMI 4x4 Matrix and
Distribution Amplifier
Setup
With the matrix power switch in the OFF position, connect an HDMI High
Speed cable from the HDMI Output of the most commonly used audio/
video source to the HDMI Input 1 located on the rear of the matrix.
Similarly, connect the remaining source devices to the HDMI Input rts Po
on the matrix.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
Next, connect an HDMI cable to the HDMI Output Port 1 on the rear of
the matrix. Connect the other end to the HDMI Input Port of the displ ay
device. Similarly, connect the remaining HDMI Output Ports from the
matrix to the other displays.
The matrix has internal memory that stores the system
information for faster switching. Please follow the steps in the
order listed: Turn ON the displays and ensure they are awake (not in
standby mode). Check the displays INPUT setting to ensure the correct
HDMI port is active.
Turn on the source devices and ensure they are awake (not in standby
mode). Connect the power adapter to the matrix. Plug the power
adapter into a surge protected AC power outlet. Turn the matrix power
switch to the ON position.
The matrix has a low power d w and is intended to be left on. If ra
the matrix is turned off, start up the system as noted above. If new
hardware is added, please perform a RESET.
To RESET the matrix, turn off the display and source devices. Power off
the matrix and unplug the power adapter from the rear of the matrix.
Wait 20 minutes for the memory of the system configuration inside of
the matrix to be deleted. llow the setup instructions above to correctly Fo
initiate the setup.
HDMI 4x4 Matrix and Distribution Amplifier
Model: K072C-013B
Specifi cations
● Independently access 4 HDMI Sources from 4 HDMI Displays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Input video signal: 5v p-p, Input DDC signal: 5v p-p (TTL)
● Data transfer speed of 6.75Gbps (2.25Gbps/channel)
● Audio formats supported: S-HD 7.1, Dolby TDT rue-HD 7.1
● Deep color up to 36-bit
● RS232 Port for control
● Maximum input cable length: Up to 20m (24AWG)
● Maximum output cable length: Up to 20m (24AWG)
● Shelf or surface mountable
● 5V DC, UL Listed power adapter
● Approximate dimensions: 10.9”W x 1.1”H x 6.1”D
277W x 28H x 156D mm
● Operating temperature range: 5 to 131°F (-15 to 55°C)
● Operating humidity range: 5% to 90% RH (no condensation)
LED indicator lights
On initial power on, all LED lights on the matrix should come on solid
blue. All the numerical LED displays will momentarily read ‘0’ and
then change to ‘1’. If less than the maximum number of Displays
are connected to the matrix (not all the outputs are used) the
numerical indicator will indicate ‘0’ for that output and there will be no
corresponding blue LED for the unused output. Blue lights HDMI OUT
will only appear for devices connected. A unused HDMI Input ports will ny
also have its blue LED unlit.HDMI IN
Operation
Manual Control: You can ope te HDMI source switching manually by ra
using the buttons labeled ‘Out” located on the front panel. Press the
button that corresponds to the output that you want to change the HDMI
source on and toggle through until the desired HDMI input source video
is being displayed. A numerical LED indicates which HDMI source input is
being shown on each output (HDTV).
Remote Control: Included with the Matrix is a Remote Control. The
remote control can control the matrix pointing it at the front of the by
matrix, targeting the integrated IR receiver labeled -IR. IR uses line-of
sight between the remote control (or IR-TX) and the receiver. The angle
which the remote will work is at about a 15° degree angle in either
direction to the receiver. If the receiver is postioned such that there
is not line-of -sight, the port labeled “IR Extender” accepts an optional
IR Receiver. This receiver enables line-of-sight if the matrix is out of
position.
LED Indicator Lights

Produkt Specifikationer

Mærke: Accell
Kategori: Modtager
Model: UltraAV K072C-013B

Har du brug for hjælp?

Hvis du har brug for hjælp til Accell UltraAV K072C-013B stil et spørgsmål nedenfor, og andre brugere vil svare dig


Modtager Accell Manualer

Accell

Accell UltraAV K078C-006B Manual

10 August 2024
Accell

Accell UltraAV K072C-011B Manual

9 August 2024
Accell

Accell UltraAV K078C-007B Manual

9 August 2024
Accell

Accell UltraAV K072C-012B Manual

8 August 2024
Accell

Accell UltraAV K072C-013B Manual

6 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Atoll

Atoll AV500 Manual

6 December 2025
Atoll

Atoll AV100 Manual

5 December 2025
Atoll

Atoll AM300 Evolution Manual

5 December 2025
AVM

AVM Evolution AS 3.3 Manual

5 December 2025
AIYIMA

AIYIMA A08 Pro Manual

5 December 2025
MKC

MKC MK3506D+ Manual

4 December 2025
AIYIMA

AIYIMA T5 Manual

3 December 2025
PRV Audio

PRV Audio MDX1800.1 Manual

3 December 2025
Topping

Topping MX5 Manual

30 November 2025
Topping

Topping Mini 300 Manual

29 November 2025