AFX Scott SCTB5054L30ENDG Manual

AFX Lettelse Scott SCTB5054L30ENDG

Læs gratis den danske manual til AFX Scott SCTB5054L30ENDG (2 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om AFX Scott SCTB5054L30ENDG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

LED Indoor Luminaires Model # SCTB3840L30ENDG

Overbed Wall Mount SCTB5054L30ENDG

120VAC / 60Hz

Page 1 of 1 8061260 R1

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due

to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property damage.

 It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120VAC, 60Hz fused circuit. This xture is not compatible with dimmers.

 Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp locations.

 Disclaimer

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian IC -005 (B) / NMB-005 (B). These limits are designed to ES

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Assembly Instructions

Step 1 Preparing for installation–

A. before installing or servicing any part of Disconnect electrical power

this xture.

B. Remove xture from carton; remove components from hardware kit.

C. Place the diuser assembly (9), channel cover (7) and hardware o to the

side.

D. Remove appropriate knockout(s) on channel assembly (1) for power

supply entry.

E. Install white cover plate (4) to junction box (not included) with two screws

(5).

F. Position the channel assembly (1) onto the wall with the “this side up”

sticker facing the proper direction and mark all appropriate mounting

locations. Take the channel assembly (1) down and punch a small hole in

the wall at each of the marked locations using a nail to see if there is a

wall stud to mount the xture to. Where there is a wall stud, use a suitable

screws (2, not included) to mount the xture. Where there is no stud to

screw into, a toggle bolt or drywall anchor (3, not included) must be used

to mount the channel assembly securely to the wall.

Wiring A–ll wiring must take place inside junction box (not included).

Caution: Make sure power is o at fuse or circuit breaker box. Check

power wires for damage or scrapes. If the power supply wires are within

three inches of the driver, use a wire suitable for at least 90C (194F). Most dwellings Note:

built before 1985 have supply wire rated to 60C. Consult a qualied electrician to ensure

correct branch circuit conductor before installing.

Step 2 ring –Wi

A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

B. Connect the green wire from the xture to the supply power source ground wire.

C. Connect black wire from the xture to the black (L) wire from supply power source.

D. Connect white wire from the xture to the white (N) wire from supply power source.

E. . Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors. Tuck all Do not mix wires

connections neatly into junction box.

Step 3 Channel cover–

A. Install channel cover assembly (7) facing the correct direction (see “this side up” sticker), connect quick disconnect (6) coming out of the divider/LED

assembly with the leads that are coming out of the channel assembly. Make certain the uplight and downlight connectors are paired correctly as these are

controlled by the 4-way pull switch Align two front hole to the channel then secure with two screws (8). .

Step 4 Mounting diuser–

A. Install the diuser (9) by aligning two side holes to channel and secure with two screws ( (1) 10).

Step 5 Pull switches operation–

A. The far right pull switch operates the uplight and downlight by pulling on the chain once to turn on the uplight, pull twice to turn on the downlight, third pull to

turn on both uplight and downlight, and forth pull to turn both lights o. The left pull switch operates the night light by single pull to turn night light on and pull

twice to turn o.

Step 6 Power to the xture can now be restored–

3ft version shown for

reference only. Individual

models may vary.