NUVO Ballerina 60/1265 Manual

NUVO Lettelse Ballerina 60/1265

Læs gratis den danske manual til NUVO Ballerina 60/1265 (1 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om NUVO Ballerina 60/1265, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Secure back plate (B) to outlet box with outlet box

screws (E), plastic wall anchor (A) and wood screws

(C).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two

raised dimples on the circular strap. Wrap the ground

wire from the fixture (if supplied) around the green

grounding screw, then connect it to ground wire from

the outlet box (if not fixed on the outlet box) using a

wire connector (not supplied). If ground wire from the

fixture is not supplied, wrap the ground wire (if not

fixed on the outlet box) from the outlet box around the

green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is round

in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place

evenly against the black wire from the outlet box. Do

NOT twist wires together before using wire connectors.

STEP 4: Fit a wire connector (not supplied) over the wires and

screw the connector clockwise until you feel firmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4, as

above, and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box. Raise face plate (F) allowing for mounting

screw (D) to protrude through the hole in the face plate

(F), and secure with finial (G).

STEP 2: Place the glass (I) over the socket (H) then secure with

retaining ring (J).

STEP 3: Install lamps. (Please do not exceed the maximum

capacity recommended on the socket.)

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to

order replacement parts. All parts for this fixture can be ordered

from place of purchase. Be sure to use exact wording from

illustration when ordering parts.

Line art shown may not exactly match the fixture enclosed.

However, the installations do apply to this fixture.

ITEM NO: 60-328 60-329 60-330 60-331 60-316

60-317 60-318 60-319 60-324 60-325

60-326 60-327 60-320 60-321 60-322

60-323 60-332 60-333 60-334 60-335

60-1264 60-1265 60-1266 60-1267

NUV

A Satco Product

LIGHTING

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lettelse
Model:	Ballerina 60/1265

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO Ballerina 60/1265 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse NUVO Manualer

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025

NUVO Terrace 60/7747 Manual

4 April 2025

NUVO 65/220 Manual

4 April 2025

NUVO Halter 60/7692 Manual

4 April 2025

NUVO Everton 60/7877 Manual

4 April 2025

Lettelse Manualer

Nyeste Lettelse Manualer

Schwaiger CALE100 511 Manual

9 April 2025

ADB Orkis Fresnel Manual

8 April 2025

Claypaky Actoris ParLED Manual

8 April 2025

ET2 Waterfall E24846-90 Manual

8 April 2025

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

Maxim Westlake 65102BK Manual

4 April 2025

Maxim Diverse 57641WTWT Manual

4 April 2025