NUVO SF77/196 Manual

NUVO Lettelse SF77/196

Læs gratis den danske manual til NUVO SF77/196 (2 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om NUVO SF77/196, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE

WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE

CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this xture. Be sure to follow the

steps in the order given. Under no circumstances should a xture be hung

on house electrical wires, nor should a swag type xture be installed on

a ceiling which contains a radiant type heating system. Read instructions

carefully. If you are unclear as to how to proceed, consult a qualied

electrician.

NOTE: Proper wiring is essential for the safe operation of this xture.

FIXTURE ASSEMBLY

Carefully remove the xture from the carton and check that all parts are

included as shown in gure. Be careful not to misplace any of the screws

or parts, which are needed to install this xture.

INSTALLATION

IMPORTANT: Do not attach xture directly to outlet box.

STEP 1: Position the back plate (B) through the xing holes onto the wall

and make marks, drill pilot holes for wood screws (C) into the wall, then

insert the plastic anchor (A) into the holes.

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised

dimples on the mounting bar. Wrap the ground wire from the xture

(if supplied) around the green grounding screw, then connect it to ground

wire from the outlet box (if not xed on the outlet box) using a wire

connector (not supplied). If ground wire from the xture is not supplied,

wrap the ground wire (if not xed on the outlet box) from the outlet box

around the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER

SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your xture. Identify which

group your xture wire(s) falls into and connect the wires according to the

directions below:

GROUP A:

Connect to Black House Wire

GROUP B:

Connect to White House Wire

BLACK WHITE

* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square

shaped or ridged and the less tracer wire is round in shape or smooth (seen

best when viewed from wire end.)

STEP 3: Take your xture wire(s) from group A and place evenly against the

black wire from the outlet box. Do NOT twist wires together before using

wire connectors.

STEP 4: Fit a wire connector over the wires and screw the connector

clockwise until you feel rmness.

STEP 5: Try gently to pull the connector off the wires. If you can pull the

connector off, carefully re-do steps 3 and 4 as above, and check again for

a rm connection.

STEP 6: Connect the xture wire from group B to the white wire from

the outlet box in the same manner. Make sure no bare wires can be seen

outside wire connectors.

ITEM NO: SF77-188, SF77-189, SF77-190, SF77-191,

SF77-192, SF77-193, SF77-194, SF77-195, SF77-196

ARTÍCULO Nº: SF77-188, SF77-189, SF77-190, SF77-191,

SF77-192, SF77-193, SF77-194, SF77-195, SF77-196

ARTICLE N°: SF77-188, SF77-189, SF77-190, SF77-191,

SF77-192, SF77-193, SF77-194, SF77-195, SF77-196

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside outlet box.

Secure back plate (B) to outlet box with outlet screws (D), then secure the

outlet box with wood screws (C) into plastic anchors (A) in the wall.

STEP 2: Place the front plate (F) over the sockets (E) and back plate (B)

to the wall.

STEP 3: Place the cups (G) over the sockets (E) to the front plate (F).

STEP 4: Install lamps (not supplied). Do not exceed the maximum capacity

recommended on the socket.

CLEANING

To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not

use abrasive materials such as scouring pads or powders, steel wool or

abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order

replacement parts. Be sure to use exact wording from illustration when

ordering parts.

FIGURE

Line art shown may not exactly match the xture enclosed. However, the installations

do apply to this xture.

La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,

las instalaciones sí aplican para esta pieza.

Les images peuvent ne pas correspondre exactement au luminaire de la boîte.

Par contre, les directives d’installation s’appliquent au luminaire.

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lettelse
Model:	SF77/196

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO SF77/196 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse NUVO Manualer

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025

NUVO Terrace 60/7747 Manual

4 April 2025

NUVO 65/220 Manual

4 April 2025

NUVO Halter 60/7692 Manual

4 April 2025

NUVO Everton 60/7877 Manual

4 April 2025

Lettelse Manualer

Nyeste Lettelse Manualer

Schwaiger CALE100 511 Manual

9 April 2025

ADB Orkis Fresnel Manual

8 April 2025

Claypaky Actoris ParLED Manual

8 April 2025

ET2 Waterfall E24846-90 Manual

8 April 2025

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

Maxim Westlake 65102BK Manual

4 April 2025

Maxim Diverse 57641WTWT Manual

4 April 2025