Altec Lansing MZW101 Manual

Altec Lansing Headset MZW101

Læs gratis den danske manual til Altec Lansing MZW101 (2 sider) i kategorien Headset. Denne vejledning er vurderet som hjælpsom af 93 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 47 anmeldelser. Har du et spørgsmål om Altec Lansing MZW101, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. Make sure the following items are

included in your package.

Ear Caps

(three sizes for maximum comfort)

USB Cable

MZW100

S Ea nestereo rpho

Item # MZW101

Quick Start Guide

3. When charging, a red LED light will illuminate. The light will turn blueCharging: .

2. For a look at the various buttons and parts of your earphones,

view the graphic below. when your unit is fully charged. Your earphones can take up to one hour to fully

charge.

5. Wearing Your Earphones

For the best sound performance and a secure, comfortable ﬁt, be sure that the

6. Listening to Music

4. Powering On Your Earphones & Pairing Them With a Bluetooth Phone

Play/Pause

Press the Power button to get music from your audio source to play or pause.

Next/Previous Song

Press and hold the Volume Up or Volume

Down buttons for two seconds to advance to

the next song or go back to the previous one.

Increase/Decrease Volume

Press the Volume Up or Volume Down

buttons to increase or decrease the

volume.

NOTE: Music will automatically pause when

a call is dialed out or when there is an incoming

call. It will resume when the call ends.

7. Using Your Earphones During Phone Calls

Last Number Redialing

Quickly tap on the Answer button twice and the last number that you dialed will be

redialed.

Answering an Incoming Call

To answer an incoming call, quickly

press the Answer button.

Ending a Call

To end a call, quickly press the Answer

button, and the call will be disconnected.

Adjusting Volume

By pressing the Volume Up or Volume

Down buttons you can increase or decrease

the volume of the phone call.

ear buds rest gently in your ear , form a seal in your ear canal, and drape around the

Use the ear cap that feels most comfortable in your ear.

---By pressing the Power button down for about 3 seconds, your

earphones will power on and connect to the last phone they were

paired with.

---In order to pair your earphones with your phone for the ﬁrst time

be sure to hold down the Power button for a full 5-7 seconds.

When ready to pair the LED light will ﬂash red and blue alternately.

--If you are having trouble pairing your earphones with your phone,

be sure that you are holding down the Power button long enough

for your earphones to go into pairing mode.

-Press and hold the Power button for around 5-7 seconds. When your earphones

are ready to pair with a Bluetooth audio source, they will go into pairing mode,

with the LED ﬂashing alternately red and blue.

-Go to the Bluetooth Manager of your Bluetooth device. Search

Bluetooth devices and select “MZW101” to start connecting.

-If required, enter the PIN code "0000” and conﬁrm the entry.

Once paired, you will hear your speaker audibly say: “You are

now paired, enjoy.”

5-7 Seconds

Volume Down/Previous

Volume Up/Next

Power/Play/Answer

Microphone

LED

Charging Port

Ear Cap

LED

IMPORTANT

MZW 110

-Once powered on, you can press and hold

the Power button again for approximately

three seconds to power o your earphones.

The LED Indicator light will brieﬂy turn red

before powering o.

NOTE: In order to save power, your

earphones will automatically power o if left

unpaired or idle for over ten minutes.

If you have previously paired your

earphones with a phone, you can press the

Power button for three seconds to power on

your earphones and they will automatically

connect with the last phone which you paired with.

Altec Lansing One Year Warranty Card

What Is Not Covered by Warranty

To Obtain Warranty Service and Troubleshooting information:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference , and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution: changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates. Uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions. May cause harmful

interference to radio or -television reception, which can be

following measures:

__ Reorient or relocate the receiving antenna.

__ Increase the separation between the equipment and receiver.

__ Consult the dealer or experienced radio/ TV technician for help.

Technical Support

For technical support issues please visit our website at www.alteclansing.com.

You can ﬁnd manuals, software and FAQ’s at the website. Can’t ﬁnd what you

are looking for? Call 1-855-292-4087 to access our technical support

information on the phone.

Item # MZ 01W1

Quick Start Guide

Produkt Specifikationer

Mærke:	Altec Lansing
Kategori:	Headset
Model:	MZW101
Kode for international beskyttelse (IP):	IPX7
Produktfarve:	Sort
Kontroltype:	Knapper
Produkttype:	Hovedtelefoner
Bluetooth:	Ja
Anbefalet brug:	Sport
Impedens:	- ohm (Ω)
Forbindelsesteknologi:	Trådløs
Batterilevetid (maks.):	6 t
Bæremåde:	I ørerne
3,5 mm stik:	Ingen
USB-tilslutning:	Ingen
Hovedtelefon frekvens:	- Hz
Driverenhed:	9 mm
Mikrofontype:	Indbygget
Batteritype:	Indbygget batteri
Ørekobling:	Intraaural
Vedvarende afspilningstid, lyd:	6 t