AMX FG2105-70 Manual

AMX Controller FG2105-70

Læs gratis den danske manual til AMX FG2105-70 (2 sider) i kategorien Controller. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 14 anmeldelser. Har du et spørgsmål om AMX FG2105-70, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Guide

NI-700 NetLinx Integrated Controller

The NI-700 (FG2105-70) is geared to meet the specific control and automation needs of a single

room environment, in which both price and functionality are the driving requirements. The NI-700 is

configured to control a limited number of video players, projectors, lights, thermostats, and other

electronic equipment.

ATTENTION!

Verify you are using the latest version of NetLinx Studio (available for download from

www.amx.com).

Port Assignment and Functionality

Ethernet Ports used by the NI Controller

Note: While the NI-700 is capable of receiving 8 and 9 bit characters, it cannot receive 7 bit, 1 stop

bit data from a serial device (ex: 9600,N,7,1).

RACK MOUNT SAFETY INSTRUCTIONS

• If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the

rack environment may be greater than room ambient. Therefore, consideration should be

given to installing the equipment in an environment compatible with the maximum ambient

temperature 50°C.

• Installation of the equipment in a rack should be such that the amount of air flow required for

safe operation of the equipment is not compromised.

• Mounting of the equipment in the rack should be such that a hazardous condition is not

achieved due to uneven mechanical loading.

• Consideration should be given to the connection of the equipment to the supply circuit and the

effect that overloading of the circuits might have on over current protection and supply wiring.

• Reliable earthing of rack-mounted equipment should be maintained. Particular attention

should be given to supply connections other than direct connections to the branch circuit (e.g.

use of power strips).

FIG. 1 NI-700

NI-700 Specifications

Dimensions (HWD): • 1 9/16" x 5 9/16" x 5 1/8" (4.01 cm x 14.10 cm x 13.00 cm)

• RU: 1

Power Requirement: • 280 mA @ 12 VDC

• Power requirements are usage dependant

Memory: • 64 MB SDRAM (not upgradeable)

• 32 MB Flash chip (not upgradeable)

• 512 Kb of Non-volatile SRAM

Microprocessor: • 304 MIPS

Weight: • 1.30 lbs (0.59 kg)

Enclosure: • Metal with black matte finish

Certifications: • FCC Part 15 Class B, CE, and IEC 60950

Front Panel Components

PROGRAM Port: RS-232 DB9 connector (male) can be connected to a DB9 port on a PC.

This port can be used with both Serial and NetLinx commands.

CONFIGURATION

DIP Switch:

8-position DIP switch sets the communication parameters for the Program

port.

IR RX LED (red): Lights when IR data is being received via the rear IR RX port.

IR LED (red): Lights during the transmission of IR or Serial data via the rear IR port.

I/O LEDs (yellow): Light when the rear I/O channels 1 - 4 are active. LED indicator for each

I/O port reflects the state of that particular port.

SERIAL LEDs

(red and yellow):

Light when the rear DB9 Ports (1 & 2) transmit or receive RS-232, 422, or

485 data.

Note: These LEDs do not reflect changes in either the RTS or CTS when

hardware handshaking is used.

MASTER LEDs • LINK/ACT (green): Lights when the Ethernet cable is connected and an

active link is established. This LED also blinks when receiving Ethernet

data packets.

• Status (green): Lights when the Controller is programmed and

communicating properly.

• Output (red): Lights when the Controller transmits data, sets channels

On and Off, sends data strings, etc.

• Input (yellow): Lights when the Controller receives data from button

pushes, strings, commands, channel levels, etc.

ID Pushbutton: Sets the NetLinx ID (Device only) assignment for the device.

Rear Panel Components

PORT 1 /2: Two RS-232/422/485 control ports use DB9 (male) connectors with XON/

XOFF (transmit On/transmit Off), CTS/RTS (clear to send/ready to send),

and 300 - 115,200 baud.

IR RX (Port 5): 4-pin 3.5 mm port connects up to 8 IRX-SM+ swivel mount or IRX-DM+

Decora mount IR receivers.

Note: The IR RX port functions using AMX IR codes (38 KHz and 455

KHz) and works ONLY with AMX IR Receivers such as the IRX-DM+ and

IRX-SM+.

I/O (Port 4): 4-channel digital I/O port for contact closure with each input being capable

of voltage sensing. Input format is software selectable with interactive

power sensing for IR ports.

Note: The I/Os are not dry closure; they are electronic switches that float

at 5V when Off. Therefore, they should not be expected to work in

situations that require true dry contact (or dry closure). The I/Os do work

with AMX PC1, PC2, UPC20 and UPC20+.

PROGRAM port (DB9)

CONFIGURATION DIP Switch

IR RX LED

MASTER Status LEDs

SERIAL Status LEDs

I/O Status LEDs

IR Status LED

ID Pushbutton

PORT 1 (RS-232/422/485)

PORT 2 (RS-232/422/485)

ETHERNET 10/100 Port (RJ45)

12VDC Power connector

IR RX connector

I/O connectors IR connectors

AxLink connector / LED

(front)

(rear)

NI-700 Specifications (Cont.)

IR (Port 3): 4-pin 3.5 mm mini-Phoenix IR/Serial port supports high-frequency

carriers of up to 1.142 MHz with the output in 3 formats: IR, Serial, Data.

Note: IR ports support data mode (at limited baud rates and wiring

distances).

AxLink Port/LED: 4-pin 3.5 mm mini-Phoenix (male) connector provides data and power to

external control devices.

Green AxLink LED indicates the status of the port.

ETHERNET

10/100 Port:

RJ-45 port for 10/100 Mbps communication. LEDs show communication

activity, connection status, speeds, and mode information:

• SPD (speed) - Yellow LED lights On when the connection speed is 100

Mbps and turns Off when the speed is 10 Mbps.

• L/A (link/activity) - Green LED lights On when the Ethernet cables are

connected and terminated correctly, and blinks when receiving Ethernet

data packets.

12VDC PWR: Power Port: 2-pin 3.5 mm mini-Phoenix (male) connector.

Operating

Environment:

• Operating Temperature: 0° C (32° F) to 50° C (122° F)

• Operating Humidity: 20% - 85% RH

• Heat Dissipation (Typical): 11.5 BTU/hr

Included

Accessories:

• 2-pin 3.5 mm mini-Phoenix female PWR connector (41-5025)

• 4-pin 3.5 mm mini-Phoenix female connector (41-5047)

• 6-pin 3.5 mm mini-Phoenix female I/O connector (41-5063)

• CC-NIRC IR Emitter

Other AMX

Equipment:

• AC-RK Accessory Rack Kit (FG515)

• CC-NIRC IR cables (FG10-000-11)

• CC-NSER IR/Serial cables (FG10-007-10)

• IRX-PP38 Plasma Proof IR Sensor (FG460)

• IRX-DM+ IR Sensor (FG458-10 and FG458-11)

• IRX-SM+ IR Sensor (FG455-01)

• PMB Pole Mount Bracket (FG531)

• STS, Serial To Screw Terminal (FG959)

• Surface Mount Bracket Accessory (FG525)

NI-700 Port Assignments

Port ICSP Port #

Serial Port #1 1

Serial Port #2 2

IR/Serial Port 3

I/O Port 4

IR RX Port 5

Ethernet Port Usage

Port type Description Standard Port #

FTP The on-board Master has a built-in FTP server. 21/20 (TCP)

SSH The SSH port functions using the same interface as Telnet but

over a secure shell where it uses SSL as a mechanism to

configure and diagnose a NetLinx system.

Note: SSH version 2 (only) is supported.

22 (TCP)

Telnet The NetLinx Telnet server provides a mechanism to configure

and diagnose a NetLinx system.

23 (TCP)

HTTP The Master has a built-in web server that complies with the

HTTP 1.0 specification and supports all of the required

features of HTTP v1.1. This port is used for unsecure HTTP

Internet communication between the web browser’s UI and the

target Master.

80 (TCP)

HTTPS/SSL This port is used by a web browser to securely communicate

between the web server UI and the target Master.

443 (TCP)

ICSP Peer-to-peer protocol used for both Master-to-Master and

Master-to-device communications.

1319 (UDP/TCP)

integration!

Solutions

This feature on the Master uses, by default, port 10500 for the

XML based communication protocol.

This port is connected to by the client web browser’s JVM

when integration! Solutions control pages are retrieved from

the on-board Master’s web server.

10500 (TCP)

Produkt Specifikationer

Mærke:	AMX
Kategori:	Controller
Model:	FG2105-70
Vægt:	590 g
Relativ luftfugtighed ved drift (H-H):	20 - 85 %
Driftstemperatur (T-T):	0 - 50 °C
Dimensioner (BxDxH):	40.1 x 141 x 130 mm
RS-232-porte:	2