AMX NXA-TTS500 Manual

AMX Flad panel støtte NXA-TTS500

Læs gratis den danske manual til AMX NXA-TTS500 (2 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om AMX NXA-TTS500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Guide

TTS Secure Surface Mounting / Alternate Cable Routing

Overview

Each of the TTS Table-Top Stands features a Cable Knockout and three mounting

holes on the bottom panel that allow you to provide a secure surface-mount

installation.

When surface mounting the TTS, all cabling will enter the TTS enclosure through the

knockout on the bottom panel, using strain relief inside the enclosure (FIG. 1).

Note that in this type of installation, the rear panel connectors on the TTS are not

used, since the cables entering the enclosure through the bottom panel connect

directly to the Touch Panel, Keypad(s) or ControlPad installed in the Table-Top Stand.

Strain Relief Accessories

Included with each TTS Table-Top Stand is a cable Strain Relief and Strain Relief

Bracket that mount inside the TTS enclosure:

Cable Strain Relief (45-0004-04)

The Cable Strain Relief (FIG. 2) mounts onto the cable.

Strain Relief Bracket (62-1800-06)

The Strain Relief Bracket (FIG. 3) mounts to the bottom panel of the TTS enclosure,

using the center mounting hole.

Note that the screw that secures the Strain Relief Bracket also serves as one of three

mounting screws that secure the TTS enclosure to the mounting surface.

Preparing the Mounting Surface

1. Establish the desired location and position for the installation.

Refer to FIG. 4 and FIG. 5 for the dimensions of the bottom panel and the

location of the three mounting holes.

The mounting holes are 0.166” (4.22 mm). See “Mounting Specifications” for

details.

2. Drill three mounting holes into the surface.

Mounting Specifications

The following illustrations provide detailed dimensions of the bottom panel of the TTS

Enclosures.

NXA-TTS43X-BL and NXA-TTS500-BL

The NXA-TTS43X-BL and NXA-TTS500-BL share the same TTS enclosure (FIG. 4):

MET-TTS1/2/3-BL and AP-TTS16-BL

The MET-TTS1/2/3-BL and AP-TTS16-BL share the same TTS enclosure (FIG. 5):

FIG. 1

Cable Knockout, Strain Relief and Surface Mounting Holes on TTS Enclosures

FIG. 2 Cable Strain Relief (45-0004-04)

FIG. 3 Strain Relief Bracket (62-1800-06)

Cable Strain Relief

Cable Strain Relief Bracket

Cable Knockout

(shown with knockout removed)

Surface Mounting Holes

Mounting screw passes

through the Bracket to

secure the TTS enclosure

to the mounting surface

(see Fig. 1)

Cable with Cable Strain

Relief mounts here

FIG. 4 Bottom panel specifications - NXA-TTS43X-BL and NXA-TTS500-BL

FIG. 5 Bottom panel specifications - MET-TTS123-BL and AP-TTS16-BL

Produkt Specifikationer

Mærke:	AMX
Kategori:	Flad panel støtte
Model:	NXA-TTS500
Bredde:	177.8 mm
Dybde:	132.3 mm
Højde:	95.01 mm
Produktfarve:	Sort
Panel montering grænseflade:	- mm
Monteringstype:	Skrivebord
Kapabilitet:	NXD-500i
Maksimal vægtkapacitet:	- kg
Maksimal skærmstørrelse kompatibilitet:	- "
Antal understøttede skærme:	1
Minimal skærmstørrelse kompatibilitet:	- "
Monteringshul mønster (BxD):	4.22 x 4.22 mm