APC RBC135 Manual

APC Batteri RBC135

Læs gratis den danske manual til APC RBC135 (2 sider) i kategorien Batteri. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om APC RBC135, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Guide Smart-UPS™

APCRBC135 / APCRBC136

Hardwiring must be performed by qualified service personnel.

Adhere to all national and local electrical codes.

Internal Battery Installation/Replacement

APCRBC135

Standard 40º C

APCRBC136

High Temperature 50º C

1 Remove the two screws that secure the battery

compartment door. Remove the door.

2 Pull the battery out of the compartment to access the

battery connectors. Disconnect the battery.

3 Slide the battery part way into the UPS. Be sure the

battery connectors remain outside the UPS chassis.

Firmly push the two battery connectors together. Slide the

battery into the UPS.

4 Close the battery compartment door and secure the

door with the two screws removed in step 1.

rb001a

002a

003a

rb005a

rb005b

04b

003b

Customer support and warranty information is available at the APC Web site, www.apc.com.

Electric Industries S.A.S., American Power Conversion Corporation, or their affiliated companies. All

other trademarks are property of their respective owners. EN 990-5210A

5/2012

Connect an External Battery

Remove a knockout panel

The UPS has two knockout panels located in the battery compartment. One knockout panel is in the side wall of the

UPS. The other knockout panel is on the floor of the UPS.

Note: According to product safety standards an internal battery can not be installed in the battery

compartment if the knockout panel located on the floor of the UPS has been removed.

Refer to steps 1 and 2 on the previous page for instructions on removing the internal battery.

1 Remove the two screws that secure the battery

compartment door. Remove the door.

2 Remove the knockout panel that will be most convenient

for connecting the external battery.

Use a screwdriver to remove the knockout panel.

3 Locate the external battery cable and the strain relief

included in the box with the battery.

Clamp the strain relief on to the external battery cable.

NOTE: Once the strain relief has been clamped around

the cable it can not be opened nor removed from the cable.

Slide the external battery cable through the hole in the UPS.

Snap the strain relief into the hole in the UPS.

4 Firmly push the two battery connectors together.

Place the battery connectors into the battery compartment.

5 Close the battery compartment door and secure the

door with the two screws removed previously.

003a

rb007a

009a

003b

Produkt Specifikationer

Mærke:	APC
Kategori:	Batteri
Model:	RBC135
Bredde:	107 mm
Dybde:	144 mm
Højde:	107 mm
Vægt:	4680 g
Produktfarve:	Sort
Pakkevægt:	5140 g
Pakkedybde:	229 mm
Pakkebredde:	229 mm
Pakkehøjde:	229 mm
Batteriteknologi:	Blybatterier (VRLA)
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Driftstemperatur (T-T):	0 - 40 °C
Certificering:	REACH
Batterilevetid:	5 År
Harmoniseret systemkode (HS):	85044090
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Batteriets kapacitet:	168 VAh
Hot-swap batteri:	Ja