Berker 20292035 Manual

Berker Vægudtag 20292035

Læs gratis den danske manual til Berker 20292035 (2 sider) i kategorien Vægudtag. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Berker 20292035, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6LE007112C

Operating and

assembly instructions

Bedienings- en

montagehandleiding

Berker GmbH & Co. KG - Zum Gunterstal - 66440 Blieskastel/Germany - Telefon: + 49 6842/945-0 - Telefax: + 49 6842/945-4625 - www.berker.com - 6LE007112C - 12/2020

2029 20 ..

Room thermostat with swich

heating/cooling

Kamerthermostaat med schakelaar

verwarmen / koelen

Safety instructions

Electrical equipment may only be installed and

assembled by a qualiﬁ ed electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these instructions may

result in damage to the device, ﬁ re or other

hazards.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

(1)

(3)

(4)

(6)

(2)

(5)

Bild 1: Design and layout of the device

(1) Thermostat insert

(2) Rocker switch

(3) Frame (not within scope of delivery)

(4) Centre plate

(5) Fastening screw

(6) Setting knob

Function

The thermostat controls the temperature in enclosed

spaces. It is controlled using the measured value of

the internal temperature sensor. The thermal re-cir-

culation (thermal resistor) achieves ecient control

during heating operation.

The thermostat possesses a switch, using which it is

possible to switch between the Heating and Cooling

control types.

Correct use

- Only suitable for indoor applications.

- Installation in wall box according to DIN49073

(deep box recommended)

Operation

(7)

(6)

Bild 2: Operating elements

(6) Setting knob

(7) Switch heating/cooling

Switching heating or cooling mode

The printing of the heating/cooling slide switch is

designed for normally closed valves.

 Switch the switch to the desired position.

Heating

Cooling

The selected operating mode is executed.

Setting the temperature setpoint

Specify the room temperature setpoint using the

setting knob (6):

- Heating:

When the setpoint is undershot, the device

switches on.

- Cooling:

When the setpoint is exceeded, the device

switches on.

The setting range is max. 5°C to 30°C.

Setting value

(scale)

2 3 5 6

Temperature [°C]

5 10 15 20 25 30

Table 1: Setting values of the setting knob

 Turn setting knob to the desired setting.

Information for electricians

Installation and electrical connection

Selecting installation location

1,5 m

Bild 3: Recommended installation location

- An inside wall opposite the heating source is the

preferred installation location.

- Optimal installation height approx. 1.5 m above

the ﬂ oor.

- Avoid installation on outside walls and draught

from windows or doors at the installation loca-

tion.

- The heated room air should be able to reach the

controller without hindrance. Do not mount the

controller within shelving units or behind curtains

and similar coverings.

- Extraneous heat a ects the control accuracy.

Avoid direct sunlight and do not install near televi-

sions, radios and heating appliances, lamps,

chimneys and heating pipes.

- Avoid mounting in combination with dimmers. If

necessary, maintain the greatest possible dis-

tance between the two devices. In the case of an

arrangement one above the other, the controller

must be arranged below the dimmer.

- When mounting the device in hollow walls, en-

sure that the controller is not exposed to any

outside heating or cooling from air draughts or

rising cables, also on the rear side.

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

Connecting and mounting the device

< ϑ

Bild 4: Electrical connection

L Outer conductor (phase)

N Neutral conductor

Load connection heating/cooling

RF Thermal resistor thermal recirculation

The printing of the heating/cooling slide switch is

designed for normally closed valves. A maximum

of 5 valve drives may be connected to the device.

The N conductor must be connected to the

thermal re-circulation as a power supply, oth-

erwise large temperature variations should be

expected.

 Connect the controller according to connection

diagram

(ﬁgure 4). Observe the terminal labelling.

 Mount the rocker switch (2) in the appropriate

seat opening, according to the ﬁgure.

 Attach frame (3) and ﬁx it in the correct position

with the fastening screw (5) using the centre plate

(4).

 Slip the setting knob (6) on.

Commissioning

The thermo-bimetal of the controller requires a

certain amount of time to adjust itself to the room

temperature. For this reason, the switching point

will deviate from the room temperature directly

after mounting. Switching point accuracy will only

occur after approx. 1 to 2 operating hours.

Limiting the setting range

The temperature setting range can be limited individ-

ually using 2 setting rings under the setting knob.

(8)

(9)

(10)

Bild 5: Setting limit on the centre plate

(8) Locking pin

(9) Setting ring, maximum temperature (red)

(10) Setting ring, minimum temperature (blue)

 Pull the setting knob.

 Pull out the locking pin (8) so that the setting

rings can be moved freely against each other.

 To set the maximum setpoint, turn the red setting

ring (9) in an anticlockwise direction into the

required position.

 To set the minimum setpoint, turn the blue setting

ring (10) in a clockwise direction into the required

position.

During setting, rough orientation for the setting

can be obtained from the printed scale.

 Slip the setting knob on. In so doing, ensure that

the nose on the rotation axis is guided into the

appropriate seat recess in the controller.

Appendix

Technical data

Contact type Change-over contact

Temperature range 5-30 °C

Rated voltage AC 230 V

Rate current heating/cooling 5(2) A

Switching dierence temperature ~0.5 K

Temperature change speed

of the control path: max. 4 K/h

Degree of contamination 2

Permissible relative humidity max 95 %,

no condensation

Protection class (after complete installation

of cover) ΙΙ

Rated impulse voltage 4 kV

Connecting terminals screw terminals

- rigid 1 ... 2.5 mm²

Troubleshooting

Large temperature variations in control

No thermal re-circulation, as no N conductor was

connected.

Connect N conductor

Produkt Specifikationer

Mærke:	Berker
Kategori:	Vægudtag
Model:	20292035
Type:	Controller-kontakt
Vekselstrømsindgangsspænding:	230 V
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Husmateriale:	Plastic, Metal
Bæredygtighedscertifikater:	REACH, RoHS
Overholdelse af bæredygtighed:	Ja