Black And Decker 2912 Manual

Black And Decker Lommelygte 2912

Læs gratis den danske manual til Black And Decker 2912 (2 sider) i kategorien Lommelygte. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Black And Decker 2912, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

If you have any questions, call 1-800-9-BD TOOL (1-800-923-8665)

9.6, 12, 14.4 Volt Cordless Worklights

2909, 2912, 2914

Please take time to read this manual and pay particular attention to the safety

rules we’ve provided for your protection. If you have any questions about

your tool please call:

1-800-9-BD TOOL

(1-800-923-8665)

NOTE: Your 2909 worklight operates on a 9.6V power pack (97046 or

97148) Your 2912 worklight operates on a 12V power pack (97150 or

97051). Your 2914 worklight operates on a 14.4V power pack (97152).

Power packs are sold separately.

WARNING: When using electric tools, basic safety precautions should

always be followed to reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

Safety Rules for Worklights

1. WARNING: DO NOT OPERATE FLASHLIGHT OR CHARGER NEAR

FLAMMABLE LIQUIDS OR IN GASEOUS OR EXPLOSIVE

ATMOSPHERES. INTERNAL SPARKS MAY IGNITE FUMES.

2. WARNING: Lens and bulb become hot during use.

• During or immediately after use, don’t lay worklight flat on lens

surface.

• Don’t touch lens surface when bulb is lit.

• Handle worklight with care around any flammable surface.

• If bulb has been lit, let worklight cool for several minutes before

changing bulb.

Safety Rules for Chargers

1. Before using charger, read all instructions and cautionary markings

on (1) charger, (2) battery pack, and (3) product using battery pack.

2. DANGER: 120 volts present at charging terminals. Do not probe with

conductive objects. Danger of electric shock or electrocution.

3. If battery pack case is cracked or damaged, do not insert into charger.

Danger of electric shock or electrocution.

4. The charger and battery pack are specifically designed to work

together. DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual.

5. Do not expose charger to rain or snow.

6. To reduce risk of damage to electric plug and cord, pull by plug rather

than cord when disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped

over, or otherwise subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary.

Use of improper extension cord could result in risk of fire, electric

shock, or electrocution.

9. Two wire cords can be used with 2 or 3 wire extension cords. Only

round jacketed extension cords should be used, and we recommend

that they be listed by Underwriters Laboratories (U.L.) (C.S.A. in

Canada.) The letters WA on the cord jacket indicate that the cord is

suitable for outdoor use.

10.An extension cord must have adequate wire size (AWG or American

Wire Gauge) for safety. The smaller the gauge number of the wire, the

greater the capacity of the cable, that is 16 gauge has more capacity

than 18 gauge. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS

NAMEPLATE RATING AMPS - 0 - 10.0

Total Extension Cord Length (feet) 25 50 75 100 125 150 175

Wire Gauge 18 18 16 16 14 14 12

11.The charger is ventilated through slots in the top and the bottom of

the housing. Do not place any object on top of the charger or place

the charger on a soft surface that might block the ventilation slots

and result in excessive internal heat. Place the charger in a position

away from any heat source.

12.Do not operate charger with damaged cord or plug — have them

replaced immediately.

13.Do not operate charger if it has received a sharp blow, been dropped,

or otherwise damaged in any way; take it to an authorized B&D

service center.

14.Do not disassemble charger; take it to an authorized B&D service

center when service or repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or fire.

15.To reduce risk of electric shock, unplug charger from outlet before

attempting any cleaning. Removing the battery pack will not reduce

this risk.

16.NEVER attempt to connect 2 chargers together.

17.DO NOT store or use the tool and battery pack in locations where the

temperature may reach or exceed 105°F (such as outside sheds or

metal buildings in summer).

18.The charger is designed to operate on standard household electrical

power (120 volts). Do not attempt to use it on any other voltage!

Safety Rules for Batteries

1. Do not incinerate the battery pack even if it is severely damaged or is

completely worn out.The battery pack can explode in a fire.

2. A small leakage of liquid from the battery pack cells may occur under

extreme usage or temperature conditions. This does not indicate a

failure. However, if the outer seal is broken and this leakage gets on

your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for

a minimum of 10 minutes and seek immediate medical attention.

(Medical note: The liquid is 25-35% solution of potassium

hydroxide.)

3. Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, immediately discontinue

use and do not recharge.

4. Do not carry extra battery packs in aprons, pockets, or tool boxes

along with other metal objects. Battery pack could be short circuited

causing damage to the battery pack and possibly causing severe burn

or fire.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Charging Procedure

98014/97014 (1 Hour Chargers) only

1. Plug the charger into an appropriate AC power outlet.

2. Insert the battery pack into the charger, as shown in Figure 1, making

sure the pack is fully seated in the charger. The red (charging) light

will blink continuously indicating that the charging process has

started.

3. The battery pack will be fully charged in about 1 hour under most

conditions. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

If you have any questions, call 1-800-9-BD TOOL (1-800-923-8665)

98020 (15 Minute Charger) only

1. Plug the charger into an appropriate AC power outlet. The charger will

beep twice and the red light will blink and then go off.

2. Insert the battery pack into the charger, as shown in Figure 1, making

sure the pack is fully seated in the charger. The red light will blink and

the charger will beep once indicating the charging process has started.

3. The battery pack will be fully charged in less than 15 minutes under

most conditions. This will be indicated by the red light remaining ON

and 3 audible beeps. The pack is fully charged and may be used at this

time or left in the charger.

Power Pack Insertion and Removal

To insert the power pack into your worklight, slide it into the end of the

light until it snaps into place. To remove the power pack, depress the

release buttons shown and withdraw the power pack.

Switch

To turn the light on, slide the switch forward. To turn it off, slide the switch

back.

Swiveling Head (Figure 2)

Your worklight has a swiveling head. To convert your light to a right angle

model, grasp the front end of the light forward of the switch and hold the

back end firmly. Twist the front end clockwise (as viewed from the lens)

until the head swivels 90 degrees and clicks into place. To return the head

to a straight position, rotate the head (as viewed from the lens)

counterclockwise until it clicks into the straight position.

Replacing the Light Bulb

Worklight Cat. No Replacement Bulb Cat. No.

2909 29090

2912 29120

2914 29140

To replace the light bulb, first unscrew the lens holder. Pull the bulb out of

the spring, and insert a new bulb. Reinstall lens holder.

NOTE:Do not look directly into the worklight beam.

Spare Bulb Storage (Figure 3)

To store a bulb, unscrew the lens holder and remove it. Inside the body of

the worklight is the storage socket. To remove the bulb, pull it up and out

of the storage area. a pack from the charger andNOTE: Removing

immediately inserting it into the worklight may weaken bulb life.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

nickel-cadmium battery indicates that the costs to recycle the battery at

the end of its useful life have already been paid by B&D. In some areas, it

is illegal to place spent nickel-cadmium batteries in the trash or municipal

solid waste stream and the RBRC program provides an environmentally

conscious alternative.

RBRC in cooperation with B&D and other battery users, has established

programs in the United States to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural

resources by returning the spent nickel-cadmium battery to an authorized

service center or to your local retailer for recycling. You may also contact

your local recycling center for information on where to drop off the spent

battery.

One Year Free MaIntenance

All B&D tools for Industry and Construction are covered under a one year

free maintenance program where B&D will inspect your tool for safety and

provide necessary maintenance or repairs, including normal wear and tear

parts, for one year, FREE OF CHARGE.

Full Warranty

All B&D tools for Industry and Construction are warranted to be free of

any defects in materials or workmanship. Upon thorough examination of

tool, B&D will repair or replace, at our option, any product that is

determined to be defective.

Conditions

The service/safety check and the warranty do not apply to: repairs made or

attempted by anyone other than an authorized B&D service location;

misuse, abuse, neglect, improper application of the tool; missing parts; or

normal wear and tear (after first year of ownership). Please return the

complete unit, transportation prepaid, to any B&D factory owned or B&D

authorized service center location (list provided with tool or see Yellow

Pages under “Tools Electric”).

Fig. 1

Fig. 2

Fig. 3

LENS HOLDER

BULB

BATTERY RELEASE BUTTON

SPARE BULB STORAGE

POWER PACK (NOT INCLUDED)

SWIVELING HEAD

SWITCH

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A. F#154530

(OCT96-2)

Printed in Taiwan

Produkt Specifikationer

Mærke:	Black And Decker
Kategori:	Lommelygte
Model:	2912

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker 2912 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lommelygte Black And Decker Manualer

Black And Decker BDV157 Manual

28 Juli 2024

Black And Decker BDBB226 Manual

22 Juli 2024

Black And Decker BCL101 Manual

19 Juli 2024

Black And Decker BDCCF18N Manual

1 April 2024

Black And Decker BDLB14 Manual

21 November 2023

Black And Decker 2912 Manual

4 November 2023

Black And Decker BDLB28 Manual

20 August 2023

Black And Decker 2909 Manual

25 Marts 2023

Black And Decker FSL12 Manual

18 December 2022

Black And Decker VP369 Manual

18 December 2022

Lommelygte Manualer

Nyeste Lommelygte Manualer

Milwaukee HL-SF Manual

13 August 2025

Milwaukee IR-HL450 Manual

13 August 2025

Milwaukee IR PL250 Manual

12 August 2025

Milwaukee ML-LED Manual

12 August 2025

Milwaukee M18 URSL Manual

12 August 2025

DeWalt DCL183 Manual

9 August 2025

Dometic GLO-A400 Manual

8 August 2025

Emos P4533 Manual

31 Juli 2025

Emos P4538 Manual

31 Juli 2025

Emos P4540 Manual

31 Juli 2025