Blebox dimmerBox Manual

Blebox Smart hjem dimmerBox

Læs gratis den danske manual til Blebox dimmerBox (2 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Blebox dimmerBox, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
The device requires pre-conguration! After the rst start, select
the type of light source controlled. The incorrect selection can
cause irreparable damage to the controller and to light source.
It is forbidden to connect dierent types of light sources to the
controlled circuit as well as to change the load type with the
connected controller.
After clicking on the device name, a window will appear informing you that
you need to select the type of load (the type of lighting that the dimmerBox
will control). Go to “Settings” (icon at the top-right corner of the screen) and
select the appropriate option in the "Load Type" box.
Remember that choosing the wrong option it can cause permanently
damage to the controller and to the light source!
If you change the load type in the future, e.g. by replacing the traditional
bulbs with LEDs, rst select the load type for "None", remove old bulbs, add
new ones and in the next step change the load type to "LED bulb". Never add
to controlled circuit, dierent types of load, e.g. a traditional bulb and a LED
bulbs, or selecting the wrong load type.
After saving the settings, go to the main panel by clicking the arrow top-left
corner of the screen. Test the controller by moving the scrollbar several times
in extreme and intermediate positions - the light source should change its
brightness.
If you have connected a wall push-button, go to the settings and then in the
"Buttons" option select the type of mounted push-button - with a single
button or two buttons. Then check its work. For a single-button, a single click
will cause that the light will switch on and switch o accordingly. Holding the
push-button generates an increase in the brightness of the light source or its
attenuation. For a button with two buttons, one of the buttons is forswitch o
(single click) or dimming (hold down) while the other is for turn on increase
the intensity of the light source.
TURN ON / OFF AND DIMM 230V LIGHTING FROM ANY PLACE IN THE WORLD
Disconnect theinstallation supply voltage before installing the controller.
Remember that any mounting works should be carried out when the mains
voltage is disconnected (switch o the mains fuse or disconnect the power
cord from the mains socket).
The controller should be installed in a place protected against adverse
environmental conditions, protected from third party access - in the ush box
or inside the enclosure of the controlled device. Remember that metallic
elements (wires, housing parts) have a negative inuence on the range of the
device, and consequently the comfort of use. It is recommended that the
device be mounted in a stable and xed position. Due to the operating
voltage of the device it is necessary that the connectors of the controller be
protected against accidental contacts or short circuits, which could cause
electric shock or damage to the device.
1
Download the free wBox application. If you have an Android mobile device,
you will nd the application in the Play Store. For iOS devices the application
is in the App Store.
By using your mobile phone or tablet, connect it to the device wireless
network. To do this, enter to your smartphone or tablet settings, then go to
setting of the WiFi network and nd the network name „dimmerBox-
-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to
this network.
Turn on the wBox application. A device will appear at the top of the screen. To
add it to the application, click on "plus" on the right side of the name. To
pre-congure the controller, click on the default device name.
2 FIRST START
You can also set the conguration using the web browser
of your phone / tablet. After connecting to the wireless
network of the controller, turn on the browser and go
website www.blebox.eu
brightness controller for 230v lighting
with μWiFi technology
CONNECTION DIAGRAM
light source
INSTALLATION - BASICS
User manual
SAFETY RULES
Read the diagram and then proceed to install the controller. Pay particular
attention to the designation of the controller connectors. Start with power
wires - phase L (usuallybrown) and neutral N (blue). Then, connect the load. If
you only want a local control with a wall switch, connect the wall push-button
according to the diagram. To control using only your phone or Tablet, it is not
necessary to install the wall push-button.
The controller supports all types of double monostable push-button. The order
of connection of the S1 / S2 input, to the right / left push-button does not
matter at the installation stage - it can be set at a later stage of the controller
conguration.
After making sure that the device is connected in accordance with the diagram
and that there are no metal components near the controllerwhich may
accidentally cause short-circuit, start the device by turning on the power
(turning on the mains fuse or connecting the power cord to the power outlet).
N
L
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Do not connect the device to loads exceeding the permitted
values.
Using dimmerBox with magnetic low-voltage (MLV) transformers
is strictly forbidden and can cause a device damage and risk of
re.
The installation of the device to a power mains that does not
meet the quality requirements dened by PN-EN 50160, will
result in the loss of the warranty.
DANGER!: Risk of electric shock! Even with the device turned o,
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
direct connection (as Access Point),
Wi-Fi connection via a stan- dard router,
connection with access from any location
in the world (requires only access
to the Internet)
Apple iPhone, Apple iPad, iPad Mini,
Android, computers and mobile devices
supporting HTML5
230V AC Dimmable LED,
Incandescent/Halogen,
Electronic Low-voltage (ELV)
made of polyurethane composition not
containing halogens, self-extinguishing for
thermal class B (130 °C)
230 V AC
250 W
2
logical, active when connected to N,
congurable
230 V AC
<1W
output phase
bi-directional, encrypted
in the ush-mounted box,
inside the wall, inside the housing
of the dimming device
IP20
2.4 GHz
μWiFi, compatible with WiFi, 802.11g
48 x 38 x 23 mm
leading edge, trailing edge
housing
supply voltage
control modes
energy consumption
maximum voltage
type of control outputs
maximum load
dimensions
communication standard
transmission type
mode
number of inputs
type of inputs
protection level
mounting method
radio frequency
compatible devices
3
Once you turn on the controller for the rst time, you can proceed to its
further conguration. Being connected to the WiFi network emitted by the
device, in the control panel of the wBox application select the device, then go
to “Settings” (icon at the top-right corner of the screen).
You can change the name of the device that is displayed in the wBox
application. In addition, you can change the name and password of its
generated WiFi network. Remember that changing the network name or
password will disconnect the device immediately after you click the "Save"
button, so re-connect to the device using the newly assigned network name
and password.
You can add the controller to your home WiFi network to control it through
this home network or from anywhere in the World. To do this, in the "Connect"
settings section, select a network name from the list and press "Connect". If is
required, enter the WiFi network password. During the connection of the
controller to your home network, the phone / tablet may disconnected from
the network. In this case, you will need to reconnect your phone / tablet to the
controller network.
Please remember that in order to control the device outside the local WiFi
network, from anyplace in the World by using the wBox application, the
option "Remote access enabled" in the controller settings must be set to "Yes".
Once you've nished conguring the WiFi network, you can disconnect your
phone/tablet from the controller network and connect your mobile device
directly to your home WiFi network. The control from the wBox application
will work the same way as when the phone / tablet is connected to the
controller network. If the user leaves the local network, for example, leaving
home or using the mobile data, the wBox application will signal this state as
"Remote mode". In this case, the devices can be controlled, but for security
reasons settings are not available.
ACCESS POINT AND WIFI NETWORK SETTINGS
TECHNICAL SPECIFICATIONS
for more information visit our website
www.blebox.eu
or send us an email to: info@blebox.eu
support is available at support@blebox.eu
ADDITIONAL INFORMATION
SOFTWARE UPDATE
LOCATION AND TIME OF THE DEVICE,
SCHEDULE
To update the software in the controller, connect it to your home WiFi network
(see "Access Point and WiFi settings" section) which is connected to the
Internet. Go to “Settings” (icon at the top-right corner of the screen) and click
the "Get new rmware" button in the nal section on settings. Wait about 1
minute, do not close the interface and don’t perform other actions. The device
will download the latest software. The software version number, hardware
version and device identier can be read at the bottom of the settings screen.
The controller has the ability to work according to a given schedule. To make
this possible, set the device's time. Go to settings in the "Device time" section,
click "Change timezone". Then select your region and location from the list,
conrm your selection clicking the "Save" button. The device will synchronize
its time with the server time (if the controller is in a WiFi network with access
to Internet) or it will download time from the phone / tablet. It is recommen-
ded that the controller is always connected to a WiFi network with Internet
access so that it can automatically synchronize its clock.
To be able to control devices using the local sunrise and sunset, you must also
select the location of the controller. You can specify the location of the device
using a smartphone or tablet. In the section "Device location", click "Set
locations". Browser will ask whether to share locations - allow. In the "Coordi-
nates" eld, should appear the approximate coordinates of your location. If
the "Set locations" button blinks red with the word "Error", or the "Coordina-
tes" eld did not change the value from "Not set" to numeric data, a failurehas
occurred during the location download. You should make sure that the phone
/ tablet has a GPS module and that the sharinglocation service is enabled on
the phone.
Adding schedule entries can be performed by clicking the "Add item" button
in the "Schedule" section of settings. You can select the days in which the task
will be performed, the type of entry (at a specic time, or relative to sunrise /
sunset - only having a correctly set location) and set the parameters of the
task. The set tasks will be visible as a list, individual entries can be edited or
deleted.
lights types

Produkt Specifikationer

Mærke: Blebox
Kategori: Smart hjem
Model: dimmerBox

Har du brug for hjælp?

Hvis du har brug for hjælp til Blebox dimmerBox stil et spørgsmål nedenfor, og andre brugere vil svare dig


Smart hjem Blebox Manualer

Blebox

Blebox SwitchBox Manual

29 August 2024
Blebox

Blebox switchBoxD Manual

29 August 2024
Blebox

Blebox wLightBoxS Manual

29 August 2024
Blebox

Blebox wlightbox Manual

29 August 2024
Blebox

Blebox dimmerBox Manual

29 August 2024
Blebox

Blebox LightBox Manual

29 August 2024

Smart hjem Manualer

Nyeste Smart hjem Manualer

Homematic IP

Homematic IP HM-PB-6-WM55 Manual

2 Oktober 2025
Salus

Salus TRV3RF Manual

1 Oktober 2025
Salus

Salus SIR600 Manual

1 Oktober 2025
Homematic IP

Homematic IP HM-LC-Bl1PBU-FM Manual

29 September 2025
Homematic IP

Homematic IP HmIP-FROLL Manual

29 September 2025
TP-Link

TP-Link Tapo S515D KIT Manual

29 September 2025
Brilliant

Brilliant Nexus Home Ultimate 21465 Manual

29 September 2025
Olight

Olight Ostrip Manual

29 September 2025
Shelly

Shelly Pro 3 Manual

27 September 2025
Shelly

Shelly Dimmer 2 Manual

27 September 2025