Blebox SwitchBox Manual

Blebox Smart hjem SwitchBox

Læs gratis den danske manual til Blebox SwitchBox (2 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Blebox SwitchBox, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Test the work of the controller, by clicking the ON / OFF button, paying
attention to the behavior of the connected load. If you have connected a wall
push-button, check its work.
In the default conguration of the controller, for a mono-stable push-button,
holding down the push-button should cause that the load turn on, releasing
the pushbutton will turn o the load. To change this behavior, go to the
settings (button at the top-right corner of the screen) and then select "Set
actions triggered by input", for the corresponding action select the appropria-
te action type for the given trigger. You can congure 10 actions for a
push-button. For example, to switch on / o the lighting each time you press
the button, select the action type as "toggle state" and as trigger select “short
click”.
Also check the selection in the "state after restart" option, which determines
how the controller behaves after a restart caused by, for example, a power
failure. You can choose whether the load should be on, o, remain as before
the restart (if it was o then it has to continue o), or take the opposite state.
CONTROL DEVICES FROM ANY PLACE IN THE WORLD
Disconnect theinstallation supply voltage before installing the controller.
Remember that any mounting works should be carried out when the mains
voltage is disconnected (switch o the mains fuse or disconnect the power
cord from the mains socket).
The controller should be installed in a place protected against adverse
environmental conditions, protected from third party access - in the ush box
or inside the enclosure of the controlled device. Remember that metallic
elements (wires, housing parts) have a negative inuence on the range of the
device, and consequently the comfort of use. It is recommended that the
device be mounted in a stable and xed position. Due to the operating
voltage of the device it is necessary that the connectors of the controller be
protected against accidental contacts or short circuits, which could cause
electric shock or damage to the device.
1
Unlock your phone or tablet and download the free wBox application. If you
have an Android mobile device, you will nd the application in the Play Store.
For iOS devices the application is in the App Store. For phones with Windows
Phone, you can download the application from the Windows Phone Store.
By using your mobile phone or tablet, connect it to the device wireless
network. To do this, enter to your smartphone or tablet settings, then go to
setting of the WiFi network and nd the network name „switchBox-
-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to
this network.
Turn on the wBox application. A device will appear at the top of the screen. To
add it to the application, click on "plus" on the right side of the name. To
pre-congure the controller, click on the default device name.
2
You can also set the conguration using the web browser
of your phone / tablet. After connecting to the wireless
network of the controller, turn on the browser and go to:
http://192.168.4.1
Read the diagram and then proceed to install the controller. Pay particular
attention to the designation of the controller connectors. Start with power
wires - phase L (usuallybrown) and neutral N (blue). Then, connect the load. If
you only want a local control with a wall switch, connect the wall push-button
according to the diagram. To control using only your phone or Tablet, it is not
necessary to install the wall push-button.
The controller supports all types of single mono-stable push-button.
After making sure that the device is connected in accordance with the
diagram and that there are no metal components near the controller which
may accidentally cause short-circuit, start the device by turning on the power
(turning on the mains fuse or connecting the power cord to the power outlet).
smart switch for electric devices
with μWiFi technology
CONNECTION DIAGRAM
INSTALLATION - BASICS
FIRST START
User manual
N
L
Device
switchBox
μWiFi AC wireless
switch controller
by blebox.eu
230V AC max 3500W
OUTL N IN
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Do not connect the device to loads exceeding the permitted
values.
The installation of the device to a power mains that does not
meet the quality requirements dened by PN-EN 50160, will
result in the loss of the warranty.
DANGER!: Risk of electric shock! Even with the device turned o,
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
SAFETY RULES
EN
3
Once you turn on the controller for the rst time, you can proceed to its
further conguration. Being connected to the WiFi network emitted by the
device, in the control panel of the wBox application select the device, then go
to “settings” (button at the top-right corner of the screen).
You can change the name of the device that is displayed in the wBox
application. In addition, you can change the name and password of its
generated WiFi network. Remember that changing the network name or
password will disconnect the device immediately after you click the "save"
button, so re-connect to the device using the newly assigned network name
and password.
You can add the controller to your home WiFi network to control it through
this home network or from anywhere in the World. To do this, in the "Connect"
settings section, select a network name from the list and press "Connect". If is
required, enter the WiFi network password. During the connection of the
controller to your home network, the phone / tablet may disconnected from
the network. In this case, you will need to reconnect your phone / tablet to the
controller network.
Please remember that in order to control the device outside the local WiFi
network, from anyplace in the World by using the wBox application, the
option "Remote access enabled" in the controller settings must be set to "yes".
Once you've nished conguring the WiFi network, you can disconnect your
phone/tablet from the controller network and connect your mobile device
directly to your home WiFi network. The control from the wBox application
will work the same way as when the phone / tablet is connected to the
controller network. If the user leaves the local network, for example, leaving
home or using the mobile data, the wBox application will signal this state as
"remote mode". In this case, the devices can be controlled, but for security
reasons settings are not available.
direct connection (as access point), Wi-Fi
connection via a standard router,
connection with access from any location in
the world (requires access to the Internet)
Apple iPhone, Apple iPad, iPad Mini,
Android, Windows Phone, computers and
mobile devices operating a fully HTML5,
Apple watch support coming soon
Communication mode
Control with
ACCESS POINT AND WIFI NETWORK SETTINGS
TECHNICAL SPECIFICATIONS
For more information visit our website
www.blebox.eu
Or send us an email to: info@blebox.eu
Support is available at support@blebox.eu
ADDITIONAL INFORMATION
SOFTWARE UPDATE
LOCATION AND TIME OF THE DEVICE,
SCHEDULE
To update the software in the controller, connect it to your home WiFi network
(see "Access Point and WiFi settings" section) which is connected to the
Internet. Go to “settings” (button at the top-right corner of the screen) and
click the "get new rmware" button in the nal section on settings. Wait about
1 minute, do not close the interface and don’t perform other actions. The
device will download the latest software. The software version number,
hardware version and device identier can be read at the bottom of the
settings screen.
The controller has the ability to work according to a given schedule. To make
this possible, set the device's time. Go to settings in the "device time" section,
click "change timezone". Then select your region and location from the list,
conrm your selection clicking the "save" button. The device will synchronize
its time with the server time (if the controller is in a WiFi network with access
to Internet) or it will download time from the phone / tablet. It is recommen-
ded that the controller is always connected to a WiFi network with Internet
access so that it can automatically synchronize its clock.
To be able to control devices using the local sunrise and sunset, you must also
select the location of the controller. You can specify the location of the device
using a smartphone or tablet. In the section "device location", click "set
locations". Browser will ask whether to share locations - allow. In the "coordina-
tes" eld,should appear the approximate coordinates of your location. If the
"set locations" button blinks red with the word "error", or the "coordinates"
eld did not change the value from "not set" to numeric data, a failurehas
occurred during the location download. You should make sure that the phone
/ tablet has a GPS module and that the sharinglocation service is enabled on
the phone.
Adding schedule entries can be performed by clicking the "add item" button
in the "schedule" section of settings. You can select the days in which the task
will be performed, the type of entry (at a specic time, or relative to sunrise /
sunset - only having a correctly set location) and set the parameters of the
task. The set tasks will be visible as a list, individual entries can be edited or
deleted.
made of polyurethane composition not
containing halogens, self-extinguishing for
thermal class B (130 °C)
Supply voltage 230V
Maximum current (total) 16A
16AMaximum current (channel)
Max load 3500W
Inputs number 1
Input type logical, to N
Inputs voltage 230V
Housing
Power consumption
Outputs number
Output type
less than 1W
1
relay
bi-directional, encrypted
Protection rating IP20
Transmission frequency 2.4GHz
μWiFi, compatible with WiFi, 802.11gCommunication standard
Dimensions
Transmission
39 x 47 x 23 mm

Produkt Specifikationer

Mærke: Blebox
Kategori: Smart hjem
Model: SwitchBox

Har du brug for hjælp?

Hvis du har brug for hjælp til Blebox SwitchBox stil et spørgsmål nedenfor, og andre brugere vil svare dig


Smart hjem Blebox Manualer

Blebox

Blebox SwitchBox Manual

29 August 2024
Blebox

Blebox switchBoxD Manual

29 August 2024
Blebox

Blebox wLightBoxS Manual

29 August 2024
Blebox

Blebox wlightbox Manual

29 August 2024
Blebox

Blebox dimmerBox Manual

29 August 2024
Blebox

Blebox LightBox Manual

29 August 2024

Smart hjem Manualer

Nyeste Smart hjem Manualer

Homematic IP

Homematic IP HM-PB-6-WM55 Manual

2 Oktober 2025
Salus

Salus TRV3RF Manual

1 Oktober 2025
Salus

Salus SIR600 Manual

1 Oktober 2025
Homematic IP

Homematic IP HM-LC-Bl1PBU-FM Manual

29 September 2025
Homematic IP

Homematic IP HmIP-FROLL Manual

29 September 2025
TP-Link

TP-Link Tapo S515D KIT Manual

29 September 2025
Brilliant

Brilliant Nexus Home Ultimate 21465 Manual

29 September 2025
Olight

Olight Ostrip Manual

29 September 2025
Shelly

Shelly Pro 3 Manual

27 September 2025
Shelly

Shelly Dimmer 2 Manual

27 September 2025