Bobrick B-823 Manual


Læs gratis den danske manual til Bobrick B-823 (1 sider) i kategorien Sæbedispenser. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Bobrick B-823, eller vil du spørge andre brugere om produktet?

Side 1/1
HOW TO MOUNT DISPENSER
1. Place Shank and Latch Assembly through 1" diameter hole
in counter top. Make sure the rubber gasket is between the
shank and the counter top.
2. Below the counter, push the O-Ring and Rosette Washer
up and around the shank and secure them by threading the
Mounting Nut.
3. Thread the Bottle Cap Assembly to the end of the Shank
below the counter.
4. Thread the Bottle to the Bottle Cap Assembly.
5. Push the funnel through the top of the shank above the
counter until it snaps into place.
6. Install the Foam Dispensing Assembly by aligning the round
hole of the escutcheon with the middle of the red latch. Push
down gently and rotate clockwise until the assembly locks into
place.
HOW TO FILL DISPENSER
1. Insert BobKey into the round hole of the escutcheon and
rotate the escutcheon counterclockwise to disengage the
Foam Dispensing Assembly.
2. Fill the dispenser with FOAM SOAP ONLY by pouring through
the funnel.
3 Unit is filled when the funnel floats up.
4. Dispenser may also be filled by removing the bottle from
beneath countertop.
5. If a shorter shank is desired, remove soap pump assembly,
then cut shank at break in threads. The same length removed
from the shank should be removed from the bottom of
the funnel and top of supply tube connected to the foam
dispensing assembly.
Note: When first using a new dispenser, the dispenser will initially
need to be pumped several times for the soap to go through the
entire dispenser. In some installations, this may take up to 50 pumps.
HOW TO MAINTAIN DISPENSER
For proper maintenance, the soap pump assembly should be flushed
every six months by filling the bottle with warm water and pumping
the unit several times. Remove excess water and refill with soap.
INSTALLATION AND MAINTENANCE INSTRUCTIONS
Bobrick Models B-823, B-8231, B-8236, B-82316
Manual Foam Soap Dispensers
REPLACEMENT PARTS LIST
24-17 BobKey
823-32 Foam Dispensing Assembly Kit 4" spout for 1-L Bottle
823-33 Duckbill Kit
823-34 Basin Mounting Kit 1-L Bottle
8231-32 Foam Dispensing Assembly Kit 4" spout for 0.6-L Bottle
8231-34 Basin Mounting Kit 0.6-L Bottle
8236-32 Foam Dispensing Assembly Kit 6" spout for 1-L Bottle
823-35 Bottle & Cap Kit 1-L (34 oz.) Bottle
82316-32 Foam Dispensing Assembly Kit 6" spout for 0.6-L Bottle
8231-35 Bottle & Cap Kit 0.6-L (20 oz.) Bottle
BobKey
24-17
Foam
Dispensing
Assembly
Funnel
Counter
Mounting Nut
O-Ring
Rosette
Washer
Bottle
Bottle Cap
Assembly
Bottle
&
Cap Kit
Basin
Mounting
Kit
Shank & Latch
Assembly
Gasket
Supply
Tube to
Pump
Connection
Shank
Duckbill
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, New York 12065-1350 • Tel: (518) 877-7444 • FAX: (518) 877-5029
6901 Tujunga Ave, North Hollywood, California 91605-6213 • Tel: (818) 982-9600 • FAX: (818) 503-1102
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Ontario East: Tel: (877) 423-6555 • FAX: (877) 423-8555
• Manitoba West: Tel: (877) 423-6444 • FAX: (877) 423-8444
© 2017 by Bobrick Washroom Equipment, Inc.
Form No. 823-69 r2/28/17 Printed in U.S.A.


Produkt Specifikationer

Mærke: Bobrick
Kategori: Sæbedispenser
Model: B-823

Har du brug for hjælp?

Hvis du har brug for hjælp til Bobrick B-823 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Sæbedispenser Bobrick Manualer

Bobrick

Bobrick B-8221 Manual

15 Juni 2025
Bobrick

Bobrick B-823 Manual

15 Juni 2025
Bobrick

Bobrick B-820 Manual

15 Juni 2025
Bobrick

Bobrick B-82216 Manual

15 Juni 2025

Sæbedispenser Manualer

Nyeste Sæbedispenser Manualer