Broan 192 Manual

Broan Varmeapparat 192

Læs gratis den danske manual til Broan 192 (16 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Broan 192, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

MODELS 192 • 194 • 198

Page 1

Wall Heater

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE

INSTALLING OR USING THIS HEATER.

To reduce the risk of fire, electric shock, or injury

to persons, observe the following:

1. Use this unit only in the manner intended

by the manufacturer. If you have questions,

contact the manufacturer at the address or

telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch

power off at service panel and lock the service

disconnecting means to prevent power from

being switched on accidentally. When the

service disconnecting means cannot be

locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring

must be done by a qualified person(s) in

accordance with all applicable codes and

standards, including fire-rated construction

codes and standards.

4. When cutting or drilling into wall or ceiling,

do not damage electrical wiring and other

hidden utilities.

5. This heater is hot when in use. To avoid burns,

do not let bare skin touch hot surfaces. Keep

combustible materials, such as furniture,

pillows, bedding, papers, clothes, etc. and

curtains at least 3 feet (0.9 m) from the front

of the heater.

6. Extreme caution is necessary when any

heater is used by or near children or invalids

and whenever the heater is left operating

and unattended.

7. Do not operate any heater after it

malfunctions. Disconnect power at service

panel and have heater inspected by a

reputable electrician before reusing.

8. Do not use outdoors.

9. To disconnect heater, turn controls to

off, and turn off power to heater circuit at

main disconnect panel (or operate internal

disconnect switch, if provided).

10. Do not insert or allow foreign objects to

enter any ventilation or exhaust opening, as

this may cause an electric shock or fire, or

damage the heater.

11. To prevent a possible fire, do not block air

intakes or exhaust in any manner.

12. A heater has hot and arcing or sparking

parts inside. Do not use it in areas where

gasoline, paint, or flammable vapors or

liquids are used or stored.

13. Use this heater only as described in this

manual. Any other use not recommended

by the manufacturer may cause fire, electric

shock, or injury to persons.

14. Install heater at least 12 inches from floor or

any adjacent wall.

15. To avoid electrical shock: Do not install

unit in a tub or shower enclosure or any

location where it may come in contact with

water. Never place a switch where it can be

reached from a tub or shower.

16. This product may ONLY be installed vertically

in a wall. Do not mount in any other position.

17. Do not connect heater to dimmer switch or

speed control.

18. This product must be grounded.

SAVE THESE INSTRUCTIONS

MODELS 192 • 194 • 198

Page 2

PLANNING

This heater is intended to be used to supply

supplemental heat from a wall location in new or

existing construction.

Choose a location where edge of heater will be

at least 12” from the floor or any adjacent vertical

surface.

The heater can be operated using its built-in ther-

mostat or a remote thermostat (such as the Model

86W Line-Voltage thermostat or an appropriate

low-voltage thermostat and transformer/relay). The

Model 85 Kit is available for surface-mount appli-

cations. Purchase these accessories separately.

Plan to supply the heater with proper line voltage

and appropriate power cable.

NOTE: Power can be tapped from a nearby circuit

depending on the heater wattage required and the

amperage rating of the circuit.

Heater can be converted to half-wattage to avoid

overloading such circuits.

MODEL VOLTS AMPS WATTS BTU/HR

192 240 8.33/4.17 2000/1000 6827/3413

194 240 12.50/6.25 3000/1500 10240/5120

198 240 16.67/8.33 4000/2000 13653/6827

Bold ratings are factory wired.

See “OPTIONAL WIRING CONVERSIONS” sec-

tion for wattage conversion instructions.

Follow these basic steps when installing this heater:

1) Nail housing to studs.

2) Connect power cable.

3) Fasten heater assembly and grille to housing.

DRYWALL

THERMAL

OVERLOAD

GRILLE

BUILT-IN

THERMOSTAT

HEATER HOUSING

POWER CABLE

Produkt Specifikationer

Mærke:	Broan
Kategori:	Varmeapparat
Model:	192

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan 192 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Varmeapparat Broan Manualer

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

2 September 2024

1 September 2024

1 September 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

Grunkel RAC-10 PIROS DIGITAL Manual

13 September 2025

Livoo DOM501 Manual

12 September 2025

Gorenje IR1200W Manual

12 September 2025

Gorenje IR800W Manual

11 September 2025

Master XL91 Manual

11 September 2025

Gorenje IR540W Manual

11 September 2025

Master XL9SR Manual

11 September 2025

DeLonghi HFS50D15 Manual

11 September 2025

Flex TJ 10.8/18.0 Manual

11 September 2025

Dometic TwinBoost 4000 Manual

11 September 2025