Bushman DF30-HD Manual

Bushman Køleskab DF30-HD

Læs gratis den danske manual til Bushman DF30-HD (8 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Bushman DF30-HD, eller vil du spørge andre brugere om produktet?

Side 1/8
DF30-HD
30L 12V / 24V
Drawer Fridge Freezer
Owners Manual & Operating Instructions
Please read carefully
before use and
installation
2
Bushman DF30-HD. Please read these
instructions carefully before installation
and use.
Warnings
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure they do not play with
the appliance.
The instructions for Class III appliances shall state that it must
only be supplied at safety extra-low voltage corresponding to
the marking on the appliance.
This appliance is suitable for camping use.
Do not expose the appliance to rain.
Do not store explosive substances such as flammable –
propellant in this appliance.
Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
Keep ventilation openings in the appliance enclosure or in the
built-in structure clear of obstruction.
Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by the
manufacturer.
Do not use electrical appliances inside the food storage
compartments of the appliance, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Important information
Please do not lay your fridge on its back, top or sides
or at any angle exceeding 30º. If your fridge has been
handled this way, stand the fridge upright for 12 hrs to
allow the internal fluids to redistribute evenly before use.
Never operate your fridge directly from a 240 V or AC
power supply.
Do not use a modified sine wave inverter to operate your
fridge.
Prior to installation
Delivery
At delivery, please check that the fridge is complete and is not
damaged in any way. Remove all packaging and securing tapes
from the fridge. Do not connect an appliance that has been
damaged, contact Bushman immediately.
Installation
Installation of the DF30-HD must be completed by a suitably
trained professional only.
Power supply
Your fridge must be connected to a stable and regulated 12 V or
24 V DC power supply only. The compressor will automatically
detect which voltage is present and adjust accordingly.
Wiring
Always wire your fridge directly to your battery terminals. Do
not run the wires on a shared circuit, via a buss bar or battery
management system. Please also ensure the negative wire is
wired directly to your battery, not to a chassis. If the power cord
is damaged, it must be replaced by the manufacturer, a service
agent or similarly qualified persons to avoid hazard.
Ensure the wiring polarity is correct. Connect the red wire to the
positive terminal (+) and the white wire to the negative terminal
(-). Never connect bare electric wires. Use only connections of a
size suitable for the cross section of the wire being used.
CROSS SECTION
IN MM
2
AWG (AMERICAN
WIRE GAUGE)
MAXIMUM LENGTH OF WIRE IN
METRES
12 V 24 V
. .

 
10 108 20
Isolation switch and fuse
We recommend installing an isolation switch for the fridge circuit
as close to your battery bank as possible. Any switches must have
a breaking load not less than 20 A on 12 V or 10 A on 24 V.
The power supply wiring must also be protected with a 15 A fuse.
Installation in a cavity
To avoid a hazard due to instability of the appliance it must be
fixed in accordance with these instructions. Your new fridge is
designed to be installed in a cavity. We recommend allowing
a minimum 5mm gap on each side and the top for ease of
installation. A minimum gap of 40mm is required for the rear.
Refer to the following table for the recommended cut-out
dimensions.
MODEL CUT-OUT CAVITY DIMENSIONS (MM)
WIDTH DEPTH HEIGHT
DF   
Mounting option 1 – Internal sleeves
There are 2 internal mounting sleeves on the inside of the fridge
cabinet. Access is provided by removing the plastic tub. Gently
lever o the plastic caps. M5 screws or bolts need to be used. Drill
4mm pilot holes through the plastic sleeve and right through the
fridge cabinet sides. Put a small nylon washer onto the screw /
bolt heads before inserting. Ensure that the exterior of the fridge
cabinet is flush with your cabinetwork before aixing the screws
/ bolts. If there is a gap, pack it out with a suitable hard material.
Check for screw / bolt tightness after your first trip.


Produkt Specifikationer

Mærke: Bushman
Kategori: Køleskab
Model: DF30-HD

Har du brug for hjælp?

Hvis du har brug for hjælp til Bushman DF30-HD stil et spørgsmål nedenfor, og andre brugere vil svare dig