Café CEP90362TSS Manual

Café Ovn CEP90362TSS

Læs gratis den danske manual til Café CEP90362TSS (24 sider) i kategorien Ovn. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Café CEP90362TSS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

Installation

Instructions

BEFORE YOU BEGIN

Read these instructions carefully and completely.

• IMPORTANT — Save these instructions

for local inspector’s use.

• IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Product failure due to improper installation is not

covered under the Warranty.

•

WARNING

This appliance must be properly

grounded.

• ATTENTION INSTALLER

ALL COOKTOPS MUST BE HARD WIRED

(DIRECT WIRED) INTO AN APPROVED

JUNCTION BOX. A “PLUG AND RECEPTACLE”

IS NOT PERMITTED ON THESE PRODUCTS.

• Proper installation is the responsibility of the

installer and product failure due to improper

installation is NOT covered under warranty.

• Consider recycling options for your appliance

packaging material.

30 and 36”

Electric Cooktop - Radiant

Excludes Down-Draft Models

MATERIALS YOU WILL NEED

TOOLS NEEDED

CUTTING THE COUNTERTOP

If you are installing the cooktop in a solid surface

material such as granite, quartz or any other natural

or synthetic solid surface, we recommend that the

cutout be prepared by a professional cabinet or

countertop installer.

Cooktop cutouts in wood or wood-laminate

countertops may be able to be prepared using a

saber saw and electric drill.

PARTS INCLUDED

31-2001182 Rev. 0 10-22 GEA

Wire NutsJunction Box

Saber Saw

Pencil

Safety Glasses

1/8” Drill Bit & Electric or

Hand Drill

Ruler or Straightedge

Phillips Head

Screwdriver

2 Hold Down

Brackets

4 Screws

(WB01X1137)

Foam Tape

WB06K5042

90º or Straight

Squeeze Connector

for 1” Conduit

Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.

In Canada, call 1.800.561.3344 or visit GEAppliances.ca.

2 31-2001182 Rev. 0

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

FOR YOUR SAFETY

• For Personal Safety, remove house fuse or open

circuit breaker before beginning installation. Failure to

do so could result in serious injury or death.

• Be sure your cooktop is installed properly by a

qualified installer or service technician.

• To eliminate the risk of burns or fire due to reaching

over heated surface elements, cabinet storage

located above the surface units should be avoided. If

cabinet storage space is to be provided, the risk can

be reduced by installing a range hood that projects

horizontally a minimum of 5" beyond the bottom of the

cabinets. Cabinet installation above the cooktop may

be no deeper than 13".

• Make sure the cabinets and wall coverings around the

cooktop can withstand the temperatures (up to 200°F)

generated by the cooktop.

• The cooktop should be easy to reach and lighted with

natural light during the day.

• Always disconnect the electrical service to the cooktop

before repairing or servicing the cooktop. This can

be done by disconnecting the fuse or circuit breaker.

Failure to do this could result in a dangerous or fatal

shock. Know where your main disconnect switch is

located. If you do not know, have your electrician

show you.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the proper voltage

and frequency, and connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or a

time delay fuse as noted on name plate and the chart below.

We recommend you have the electrical wiring and hookup

of your cooktop connected by a qualified electrician. After

installation, have the electrician show you where your main

cooktop disconnect is located.

Wiring must conform to National Electrical Code. You can

get a copy of the National Electrical Code, ANSI/NFPA No.

70-Latest Edition, by writing to:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

In Canada, wiring must conform to Canadian Electrical

Code (CEC).

The cooktop conduit wiring is approved for copper wire

connection only, and if you have aluminum house wiring,

you must use special UL approved connectors for joining

copper to aluminum.

In Canada, you must use special

CSA approved connectors for joining copper to aluminum.

Installations with Aluminum House Wiring require attention.

See Warning under NOTES: ALUMINUM WIRING, above.

You must use a two-wire, three conductor 208/240 VAC, 60

Hertz electrical system. A white (neutral) wire is not needed

for this unit. The cooktop must be installed in a circuit that

does not exceed 125 VAC

nominal to ground.

Refer to the name plate on

your cooktop for the KW

rating for your cooktop.

Name plate location

KW Rating 240v KW Rating 208V

Recommended

Circuit Size

(Dedicated)

.: .: 20 Amp

4.9 KW - 7.2 KW 4.2 KW - 6.2 KW 30 Amp

7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

NOTE TO ELECTRICIAN: The power leads supplied

with this appliance are UL recognized for connections

to larger gauge household wiring. The insulation of

these leads is rated at temperatures much higher

than the temperature rating of household wiring. The

current carrying capacity of a conductor is governed

by the wire gauge and also the temperature rating of

the insulation around the wire.

NOTE: ALUMINUM WIRING

WARNING

INSTALLATIONS WITH ALUMINUM

HOUSE WIRING REQUIRE ATTENTION:

A. Improper connection of Aluminum house wiring

to appliance copper leads can result in an

electrical hazard or fire. Use only connectors

designed for joining copper to aluminum and

follow the manufacturer’s recommend procedure

closely.

B. Aluminum to Copper wiring connections must

conform with the National Electrical code, local

codes and industry-accepted wiring practices.

C. If an anti-oxidant compound is added to the

wiring connectors, the compound should be

UL-Listed and suitable for the application

materials, voltage and temperature.

D. Connectors for joining Aluminum and Copper

wiring may be larger in size than standard

connectors. It is recommended to use a double-

gang, or larger, electrical box to enclose the

connectors joining Aluminum and Copper wiring.

Produkt Specifikationer

Mærke:	Café
Kategori:	Ovn
Model:	CEP90362TSS

Har du brug for hjælp?

Hvis du har brug for hjælp til Café CEP90362TSS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ovn Café Manualer

Café Couture C9OAAAS2RS3 Manual

21 Juni 2025

Café Couture C9OAAAS4RW3 Manual

20 Juni 2025

Café Couture C9OAAAS3RD3 Manual

20 Juni 2025

Café CEP90301NBB Manual

19 Februar 2025

Café CTS90FP2NS1 Manual

4 Januar 2025

Café CTD90DM2NS5 Manual

4 Januar 2025

Café CTD90FP2NS1 Manual

4 Januar 2025

Café CSB912M2NS5 Manual

4 Januar 2025

Café CMB903P2NS1 Manual

4 Januar 2025

Café CEP90362TSS Manual

4 Januar 2025

Ovn Manualer

Nyeste Ovn Manualer

Pegasus CR-3G Manual

16 September 2025

Neff B2CCJ7AK0B Manual

16 September 2025

Pegasus CR-8E Manual

16 September 2025

Bomann EBO 7912 Manual

16 September 2025

Vestel AMD-2011 X Manual

16 September 2025

Küppersbusch CDK 6300.0S8 Manual

16 September 2025

Alto-Shaam VMC-F3E Manual

16 September 2025

Küppersbusch CBP6550.0S4 Manual

16 September 2025

Teka HLB 8418 P Manual

16 September 2025

Pegasus CR-5G Manual

16 September 2025