Cambro MDC1520S10HD Manual

Cambro Ikke kategoriseret MDC1520S10HD

Læs gratis den danske manual til Cambro MDC1520S10HD (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Cambro MDC1520S10HD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OWNER’S

MANUAL

www.cambro.com

CAMBRO

MEAL DELIVERY CARTS

This manual applies to the following Cambro products:

Short Profile Meal Delivery Carts:

MDC1520S10

MDC1520S10HD

MDC1520S20

MDC1418S20

Tall Profile Meal Delivery Carts:

MDC1520T16

MDC1418T16

MDC1520T30

MDC1418T30

MDC1411T60

MDC1520T30

MDC1418T16

Congratulations on the purchase of your Cambro

Meal Delivery

Cart. This Owner’s Manual provides you with a step‑by‑step guide to

cleaning and maintaining your Meal Delivery Cart. If you have further

questions, please contact your Cambro Sales Representative, visit our

website www.cambro.com, or call our Customer Service Department

at USA 800 833 3003, 714 848 1555, N. Ireland & UK 0800 587 0057,

Ireland 1800 509 046.

MDC1418S20MDC1520S10

Telephone 714 848 1555 Toll Free 800 854 7631 Customer Service 800 833 3003

UM0002B REV B 6/13

D041327

I. Cleaning and Maintenance

A. Cleaning Instructions

Cart Body and Louvered Vent Panel(s)

1. Clean with mild commercial detergent.

2. Hand wash using a soft cloth or plastic or bristle brush to clean all interior

and exterior surfaces.

3. Remove louvered vent panel(s) using a Phillips type screwdriver,

clean thoroughly on both sides as well as within each louver slot.

4. Rinse with hot water.

5. Air dry or use a soft cloth to dry the cart interior and exterior thoroughly.

6. Once cart and louvered vent panel(s) are dry reinstall louvered vent panel(s).

WARNING: Do not use detergents or cleaners containing ammonia, bleach or

harsh chemicals.

WARNING: Do not use steel wool or abrasive scrub pads or brushes.

WARNING: Do not tip cart forward and lean on its open doors to drain or air dry.

WARNING: When cleaning all edges of each louvered vent panel(s) use caution

not to cause injury.

1. Effective solutions for removing lingering scents and stains:

I. Use a standard destainer or

II. An odor removing soap or

III. Sanitizer or

IV. A diluted solution of 2‑3 tablespoons of baking soda per 4 liters

of hot water or

V. 1 part lemon juice to 4 parts hot water or

VI. 1 part white vinegar to 4 parts hot water.

2. After cleaning rinse thoroughly with hot water and dry thoroughly.

Doors

1. When possible remove the doors and clean around the hinges and/or pins.

2. Clean with mild commercial detergent.

3. Hand wash using a soft cloth or plastic or bristle brush to clean all interior

and exterior surfaces.

4. Rinse with hot water.

5. Air dry or use a soft cloth to dry the cart interior and exterior thoroughly.

NOTE: MDC1520S20, MDC1418S20, MDC1520T30*, MDC1418T30*, MDC1411T60* –

To remove doors, swing door(s) out until the door knuckle is clear from

top of cart. Lift and remove door from hinge pins. To re‑install, hold door

outward from the compartment and engage door onto hinge pins.

*These models require the door lock stops to be removed rst.

MDC1520T16, MDC1418T16, MDC1520S10, MDC1520S10HD–

Remove lock clip from top hinge pin‑ between the top door knuckle and

the body top knuckle. Use a screw driver or needle nose pliers to remove

the clip. Pull the clip out from between the two allowing the hinge pin

to be pulled upward and release the door. The door can then be tipped

outward to come up and out of position. To re‑install put door on base pin

align door with top hinge and slide in top pin. Re‑install lock clip.

B. Door Maintenance

1. Latch adjustment ‑ if too tight and hard to close:

I. Loosen screws.

II. Slide latch inward towards the middle of the compartment.

III. Tighten screws when adjustment is complete.

2. Latch adjustment ‑ if too loose and not engaging securely:

I. Loosen screws.

II. Slide latch towards the middle latch strike plate.

III. Tighten screws when adjustment is complete.

C. Caster Maintenance

Caster maintenance should be performed after every cleaning.

1. Grease swivel raceway of caster using a lubricant such as Lubriplate

#930‑AA, Keystone #84EPXLT multi‑purpose grease or equivalent. Apply

grease using a grease gun with a needle nose adapter or a tube‑type

applicator such as Sta‑lube Moly‑graph Assembly Lube (Fig.6). These can

be obtained at most auto parts stores.

2. Use a light oil such as WD‑40 on the hub (Fig.7).

3. Check caster for damage and test caster spin and swivel rotation before

returning to service.

III. Replacement Parts

Please visit www.cambro.com for a complete list of replacement parts.

The model number of the Cambro cart is required to determine the correct

replacement part. The cart model number can be found on the end of the cart

above the bumper for all carts except the MDC1520S10 and MDC1520S10HD.

These cart model numbers can be found at the bottom, center of the cart under

the louvered vent panel.

TO ORDER REPLACEMENT PARTS:

• Call Cambro Customer Service at 800.854.7631 or

• Fax your order to 714.842.3430 or

• Call your local Cambro Representative or Distributor

II. Cambro Warranty

Cambro warrants to the original buyer that if a product proves defective:

1. Within 1 year from the date of manufacture, Cambro will replace the product

free of charge; or,

2. After 1 year and up to 2 years from the date of manufacture, Cambro will

grant a credit of

⁄3 off replacement product; or,

3. After 2 years and up to 3 years from the date of manufacture, Cambro will

grant a credit of

⁄3 of the original price towards a replacement product.

ABUSE OR MISUSE WILL VOID THIS WARRANTY

In the event of a defective product, your Cambro Sales Representative will collect

appropriate information, such as date of manufacture and invoice information

for warranty process. With proof of purchase to the original owner, Cambro

Manufacturing will replace the product to the original owner.

NOTE: Your Cambro Sales Representative will determine if the product should be

returned for inspection before issuing credit.

Fig. 6 Fig. 7

Produkt Specifikationer

Mærke:	Cambro
Kategori:	Ikke kategoriseret
Model:	MDC1520S10HD

Har du brug for hjælp?

Hvis du har brug for hjælp til Cambro MDC1520S10HD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Cambro Manualer

Cambro CVC75 Manual

17 September 2025

Cambro MDC1520S10HD Manual

17 September 2025

Cambro PCUPP615 Manual

17 September 2025

Cambro VBRTHD6186 Manual

17 September 2025

Cambro PCUPH615 Manual

17 September 2025

Cambro VBRTHD5519 Manual

17 September 2025

Cambro UPCH1600 Manual

17 September 2025

Cambro PCUCH615 Manual

17 September 2025

Cambro VBRTHD5186 Manual

17 September 2025

Cambro PCU1000 Manual

17 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vestil E-MT-6 Manual

17 September 2025

Canarm CBFI300 Manual

17 September 2025

Vestil LAD-MM-8 Manual

17 September 2025

Vestil FLOW-4-3 Manual

17 September 2025

Vestil LAD-MM-4-G Manual

17 September 2025

Lakeside 6205 Manual

17 September 2025

Vestil AS-383-4PK Manual

17 September 2025

Turbo Air TBC-80SB-N Manual

17 September 2025

Vestil PNU-3060 Manual

17 September 2025

Blodgett Invoq 61BG Manual

17 September 2025