Cambro VBRTHD6519 Manual

Cambro Ikke kategoriseret VBRTHD6519

Læs gratis den danske manual til Cambro VBRTHD6519 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Cambro VBRTHD6519, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Owner’s

Manual

Owner’s

Manual

Versa Food Bar

™

and Versa Work Table

Cambro Versa Food Service System

VBRHD6

VBRTHD5

Versa Food Bar: VBR5, VBRL5, VBRHD5,

VBRLHD5, VBR6, VBRL6, VBRHD6, VBRLHD6

Versa Work Table: VBRT5, VBRTL5, VBRTHD5,

VBRTLHD5, VBRT6, VBRTL6, VBRTHD6, VBRTLHD6

This manual applies to the following Versa Food Bar and Versa Work Table models:

Table of Contents

Introduction ��1

Section I Assembly ��2

Section II Mobility ��3

Section III Safety Information ��3

Section IV Cleaning and Maintenance ��3

Section V Warranty ��4

Section VI Replacement Parts ��4

Introduction

Congratulations on the purchase of your new Cambro Versa Food Bar / Versa Work Table�

This Owner’s Manual provides you with a step-by-step guide to assembling, operating and

maintaining your Versa Food Bar / Versa Work Table�

NOTE: In elementary schools and early childhood education facilities, food bars and work tables

must only serve wrapped or pre-packaged serving portions� Applies to the following models:

VBRL5, VBRL6, VBRLHD5, VBRLHD6, VBRTL5, VBRTL6, VBRTLHD5, VBRTLHD6�

If you have any further questions, please do not hesitate to contact your Cambro

Sales Representative, visit our Web site at www.cambro.com or call our Customer

Service Department at 800 833 3003.

Section I - Versa Food Bar™ and Work Table Assembly Instructions

Tools Needed For Assembly: Crescent Wrench Base Parts List

A. 1 - Food Bar Body

B. 2 - Legs with Pre-installed Casters w/ Brakes

C. 1 - Faucet

D. 2 - Brushed Metal Finish Panels for the Legs

E. 20 - 1

/2" (3,81 cm) Bolts - 10 per leg

F. 20 -

/2" (1,27 cm) Flat Washers - 10 per leg

G. 4 or 5 Well Covers: 4 well covers for 5' (152 cm) Versa Work Table,

5 Well Covers for 6' (183 cm) Versa Work Table

H. 1 - Asset Management Label

I. 20 -

/2" Internal Star Lock Washers – 10 per leg

Sneeze Guard Parts List

A. 1 - Top Shelf

B. 2 - Clear Sneeze Guard Top Panels

C. 2 - Upright Assemblies

D. 4 - Sneeze Guard End Panels

E. 2 - Top Shelf Black Thumb Screws with Finish Washers

F. 4 - White Nylon Thumbscrews

G. 4 - 1

/4" (3,18 cm) Black Rubber Flat Washers

Base Assembly Instructions

1� Place Food Bar body (part A) upside down as shown�

2� Make sure Teﬂon

tape is on faucet thread� Screw faucet (part C) into bottom of

Food Bar body� Drain faucet has "O" ring pre-installed�

3� Unpack the two decorative leg panels�

4� Place one panel to ﬁt into the panel holders on the legs� The panel should slide

into the holders� The panel can also slightly bend to ﬁt into the holders�

5� Before attaching legs to food bar body, ensure that the side with the decorative

panel is facing outward� Attach legs (part B) to body using 1

/2" (3,81 cm) bolts

with

/2" (1,27 cm) ﬂat washers (10 ea� per leg section) along with

/2" (1,27 cm)

internal star lock washers (10 ea� per leg section) on top of the ﬂat washers� Hand

tighten bolts initially� Use crescent wrench for ﬁnal tightening� Do not use power

tools or impact to tighten� Over-tightening will cause stripped threads�

6� The Asset Management label will adhere best to a smooth surface on the Versa

Food Bar/Work Table� If possible, avoid placing the label on a textured surface�

NOTE: With well covers removed, the Versa Work Table well can be used for self serve

bottled or canned beverages or packaged food products only�

WARNING: Open well should not be used to hold ice for human consumption� When well

covers are in place, work table is not acceptable for direct food contact�

WARNING: A sneeze guard is required by law for service of unpackaged or bulk foods�

Sneeze Guard Assembly Instructions

1� Place uprights (part C) in the recesses at both ends of the food bar body� The

sneeze guard positioning pins in each upright should be facing inward to the food

bar body well�

2� Place nylon thumbscrews through holes located on the bottom of each side

of the food bar body and thread the thumbscrews into the base of each upright

until tight�

3� Remove the blue protective cover from all sneeze guard panels�

4� Slide the ends of a clear sneeze guard panel between the two uprights so that

each panel end rests on top of the positioning points or pins� Repeat with the

second clear sneeze guard panel being careful not to spread the uprights so as to

cause the ﬁrst panel to drop out of position�

5� Place the top shelf so that it ﬁts on top of both uprights� With the top shelf in

place, install the black knob thumbscrew and ﬁnish washer into each upright to

tighten the top shelf in place�

6� Place one 1

/4" (3,18 cm) Black Rubber Flat Washer on the bottom pivot pin of each

clear sneeze guard end panel�

6� Lift each end of each clear sneeze guard panel assembly and position a sneeze

guard end panel so that the tallest edge lines up with the side of the upright�

7� Firmly snap the end panel into the upright� Repeat with an end panel on the other

upright� See photos A, B, and C below�

8� Position the end panels to allow the clear sneeze guard panel assembly to ﬁt

smoothly onto the sneeze guard end panels� Use the location cone as a guide to ﬁt

the parts together� See photo C below�

Base Assembly Instructions applies to the following models:

VBR5 VBR6 VBRT5 VBRT6VBRL5 VBRL6 VBRTL5

VBRTL6 VBRHD5 VBRHD6 VBRTHD5 VBRTHD6

VBRLHD5 VBRLHD6 VBRTLHD5 VBRTLHD6

Sneeze Guard Assembly Instructions applies to the following models:

VBR5 VBR6 VBRL5 VBRL6

VBRHD5 VBRHD6 VBRLHD5 VBRLHD6

a B C

Produkt Specifikationer

Mærke:	Cambro
Kategori:	Ikke kategoriseret
Model:	VBRTHD6519

Har du brug for hjælp?

Hvis du har brug for hjælp til Cambro VBRTHD6519 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Cambro Manualer

Cambro PCUPH615 Manual

17 September 2025

Cambro VBRTHD5519 Manual

17 September 2025

Cambro UPCH1600 Manual

17 September 2025

Cambro PCUCH615 Manual

17 September 2025

Cambro VBRTHD5186 Manual

17 September 2025

Cambro PCU1000 Manual

17 September 2025

Cambro UPCHT16002 Manual

17 September 2025

Cambro VBRT5519 Manual

17 September 2025

Cambro VBRTHD6519 Manual

16 September 2025

Cambro VBRTHD5158 Manual

16 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vestil TM-22-M Manual

17 September 2025

Vestil LAD-MM-4-P-YL Manual

17 September 2025

Vestil JDFT Manual

17 September 2025

Watts 800M4-QT-FZ Manual

17 September 2025

Delfield 204P Manual

17 September 2025

DeLOCK 91005 Manual

17 September 2025

Vestil PNU-2496 Manual

17 September 2025

ServIt 423PSWELEM72 Manual

17 September 2025

Kela Sinerio 22231 Manual

17 September 2025

Vestil FTTM-2 Manual

17 September 2025