Chamberlain NLS2 Manual

Chamberlain Intercomsystem NLS2

Læs gratis den danske manual til Chamberlain NLS2 (4 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om Chamberlain NLS2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

HOL D

ACT IVE

TAL K

1 3

2 4

VOLUME

MONITOR

CHANNEL

OF F

Overview

The Intercom has up to a 1000 foot (300 m) range and

allows multiple simultaneous conversations, using a

900 MHz secure digital radio link. The intercoms

form an exclusive network and respond only to other

intercoms in the network.

Carton Inventory

On/Off: To turn intercom ON, press Talk button. To

turn intercom OFF, hold down the Volume DOWN

button for 3 seconds.

Talk Button: To talk, hold down

the Talk button. All intercoms in

the network that are on the same

channel will receive the signal.

Release the Talk button when done

talking and within 10-15 seconds

press and hold the Talk button of a

different intercom to make a secure channel between

the two. Once the channel is made the other intercoms

in the network cannot hear the conversation.

Volume: Pressing the Volume DOWN button will lower

the volume and pressing the Volume UP button will

increase the volume.

Intercom

Models NLS1 & NLS1C (1)

NLS2 & NLS2C (2)

Rubber Pads

Models NLS1 & NLS1C (1)

NLS2 & NLS2C (2)

MONITOR

H DOL

OFF

V MEOLU

TAL K

ACT IVE

Operation & Features

Channel Select Button: Press

the Channel Select button to set

intercom to one of four secure

channels or the paging channel.

The default channel for the intercom

is the paging channel where all four

channel lights are lit. An intercom

on a channel can only hear an

intercom on the same channel or on

the paging channel.

Battery: The AA Alkaline batteries

(not provided) will last up to a year

depending on use. When batteries

are low intercom will emit three

beeps every ten minutes.

A DC Adapter (not provided) can

also be used to power the intercom.

In this case, the channel lights will

remain on.

Conference Mode: Conference Mode allows multiple

intercoms to participate in a conversation compared

to Normal Mode in which only two intercoms

can communicate. All intercoms must be set

to the same channel or the paging channel

to be in Conference Mode. To put intercom

in Conference Mode set Dipswitch #2 to UP

position.

Monitor Mode: Monitor Mode

is used to monitor the noise in a

speciﬁ c room. Place the intercom

in the room that is to be monitored

and press the Monitor button until

a tone is heard. For extended

Monitor usage, consider using a

plug-in transformer. Any other networked intercom can

listen to that room. If a speciﬁ c channel is selected

for Monitor Mode then only other intercoms on that

channel or on the paging channel can listen. Press the

Talk button to exit Monitor Mode. A tone will be heard

indicating Monitor Mode is no longer active.

Voice Activation Mode (VOX): Voice Activation Mode

(VOX) allows a call to be answered without pressing

the Talk button. Once a call is heard on an intercom

which has been set to VOX, a response can be given

by speaking loudly into the intercom. There will be a

slight delay when VOX is ﬁ rst activated by a voice,

but will continue to transmit audio until the

speaking stops. To put intercom into VOX,

place Dipswitch #1 to the UP position. While

in VOX mode, a call may be initiated by

pressing the TALK button.

Volume

Button

Talk

Button

Learn Button

Dipswitch #1

Dipswitch #2

AC Adapter

Models NLS1, NLS2, NLS1C & NLS2C

Wireless Portable Intercom - Extreme Range

V EOLUM

MONIT OR

C LHANNE

HOL D

OFF

ACT IVE

TALK

1 3

2 4

MONITOR

HOLD

OFF

VOLUME

TALK

ACTIVE

OPTIONAL

1 2

Channel

Select Button

Channel

Lights

Active Light

Volume

DOWN

Button

Monitor

Button

Speaker

V EOLUM

MONIT OR

CHANNEL

HOL D

OFF

ACT IVE

TALK

1 3

2 4

V EOLUM

MONIT OR

CHANNEL

HOL D

OFF

ACT IVE

TALK

1 3

2 4

Assemble Intercom

Step 1

Install 4 AA Alkaline batteries (not provided).

Step 2

Adhere rubber pads to bottom. Repeat Steps 1 and 2

for any additional intercoms.

Programming Intercom

The intercom must be programmed to at least one

other intercom to become a network or it can be

programmed into an existing network.

Create New Network

Before programming, clear memory on all intercoms.

Press the Learn button on the new intercom until a

beep is heard. Within 10 seconds put the second

intercom into Learn Mode (refer to the following table).

Each intercom will emit a tone when entering

programming mode. It may take up to 3-1/2 minutes

for a secure network to be established. Repeat for any

additional intercoms.

Add to an Existing Network

Press the Learn button on the new intercom until a

beep is heard. Within 10 seconds put any networked

intercom into Learn Mode (refer to table below).

Each intercom will emit a tone when entering

Programming Mode. It may take up to 3-1/2 minutes

for a secure network to be established. Repeat for any

additional intercoms.

NOTE: Do not program new intercoms to each other

before adding them to the network or they will form

a separate network and the memory will need to be

cleared.

Press and release the Talk button to verify network is

complete.

MONITOR

H DOL

OFF

VOLUME

TAL K

ACT IVE

MONITOR

HOLD

OFF

VOLUME

TAL K

ACT IVE

V EOLUM

MONITOR

C LHANNE

HOLD

OF F

ACT IVE

TALK

1 3

2 4

INTERCOM LEARN MODE

Press the Learn button

until a beep is heard.

HOLD

ACTIVE

TALK

1 3

2 4

VOLUME

MONITOR

CHANNEL

OFF

INTERCOM LEARN MODE

Press the Learn button

until a beep is heard.

HOLD

ACTIVE

TALK

1 3

2 4

VOLUME

MONITOR

CHANNEL

OFF

Produkt Specifikationer

Mærke:	Chamberlain
Kategori:	Intercomsystem
Model:	NLS2

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain NLS2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Intercomsystem Chamberlain Manualer

Chamberlain NLS2 Manual

31 Juli 2024

Chamberlain NTD2 Manual

24 Juli 2024

Intercomsystem Manualer

Nyeste Intercomsystem Manualer

Viking E-40-SS-EWP Manual

28 Marts 2025

Viking E-1600-40-IPEWP Manual

27 Marts 2025

Hikvision DS-KH2230T Manual

27 Marts 2025

Viking E-1600-20A-EWP Manual

27 Marts 2025

Louroe Electronics AOP-SP-PB Manual

10 Marts 2025

2N Telecommunications 9151104 Manual

20 Februar 2025

2N Telecommunications Indoor Compact Manual

20 Februar 2025

Axis TI8202 Manual

20 Februar 2025

Axis TI8904 Manual

20 Februar 2025

Rollei Xtalk Manual

5 Februar 2025